METER ZSC Bedienungsanleitung

ZSC

TABLE OF CONTENTS

1. Introduction.............................................................................................. 1

2. Operation ...................................................................................................3

2.1 Connecting With Stereo Connector ............................................................3

2.2 Connecting With Pigtail Adapter................................................................5

2.3 Viewing Sensor Data ..................................................................................5

2.4 Changing Sensor Units............................................................................... 7

2.5 Changing Digital Sensor SDI-12 Address ...................................................9

2.6 Sensor-Specific Functionality ................................................................. 10

3. System....................................................................................................... 11

3.1 Specifications.......................................................................................... 11

3.2 Components ............................................................................................ 12

4. Service....................................................................................................... 13

4.1 Maintenance............................................................................................ 13

4.2 ZSC Firmware Update .............................................................................. 13

4.3 Troubleshooting ....................................................................................... 15

4.4 Customer Support.................................................................................... 17

4.5 Terms and Conditions .............................................................................. 18

AppendixA. Compliance Certifications....................................... 19

Index ................................................................................................................. 21

18325-00

12.20.2019

ZSC

1. INTRODUCTION

Thank you for choosing the ZSC Bluetooth®Sensor Interface from METER Group.

The ZSC is a hardware accessory to support METER ZENTRA system sensors. The ZSC pairs

wirelessly with iOSTM and AndroidTM mobile devices through the ZENTRA Utility Mobile app to

display sensor measurement data and metadata (firmware version, serial number, etc.). The

ZSC works with most analog, pulse, and digital sensors supported by the ZENTRA system and

supports changing the sensor SDI-12 address for use on third-party loggers.

Verify the ZSC and its two AA alkaline batteries appear in good condition.

The latest version of the ZENTRA Utility Mobile app must be downloaded from the device’s

app store (Figure1) or the ZENTRA Apps website (Figure2) prior to connecting to a sensor and

viewing sensor data.

Figure1 ZENTRA Utility Mobile app

Figure2 QR code to ZENTRA Apps website

INTRODUCTION

Use the In-App Tutorial to become familiar with the app screens and capabilities prior to

connecting to a sensor (Figure3).

Figure3 ZENTRA Utility Mobile In-App Tutorial

ZSC

2. OPERATION

Please read all instructions before operating the ZSC to ensure it performs to its full

potential.

PRECAUTIONS

METER instruments are built to the highest standards, but misuse, improper protection, or

improper installation may damage the sensor and possibly void the manufacturer’s warranty.

Before using the ZSC, follow the recommended user instructions and arrange proper

protections to safeguard the instrument from damage.

2.1 CONNECTING WITH STEREO CONNECTOR

The ZSC communicates with mobile devices through Bluetooth®Low Energy (BLE) and the

ZENTRA Utility Mobile app (available for iOS and Android). The latest version of the app must

be downloaded prior to connecting to a sensor and viewing sensor data (Section1).

1. Insert the two AA batteries (included) into the ZSC (Figure4).

(+)

(–)(–)

Figure4 Batteries in the ZSC

2. Plug the sensor stereo connector into the ZSC stereo port (Figure5).

NOTE: If the sensor has three stripped and tinned wires,contact Customer Support to purchase a pigtail-to-

stereo adapter cable to use with the ZSC. See Section2.2 for using the adapter.

OPERATION

Figure5 Plug sensor cable into ZSC

3. Press the button on the ZSC.

4. Conﬁrm that the LED on the ZSC begins blinking blue.

5. Open ZENTRA Utility Mobile app on the mobile device.

The Connect screen will appear. ZENTRA Utility Mobile will search for and display nearby

Bluetooth-enabled ZENTRA devices (Figure6).

Figure6 Connect screen with ZSC

ZSC

6. Select the ZSC.

The ZSC main screen will appear. The ZSC is connected and ready to show sensor

measurements (Section2.3).

2.2 CONNECTING WITH PIGTAIL ADAPTER

For METER sensors to be used with non-METER loggers, the connection may have been

stripped and tinned. To connect these sensors back to the ZSC or other METER loggers,

a pigtail-to-stereo adapter cable will be needed. Contact Customer Support to obtain an

adapter cable.

The adapter cable has a connector for the stereo plug connector on one end and three wires

(or pigtail adapter) for connection to a data logger on the other end. The stripped and tinned

wires have the same termination as in Figure7: the brown wire is excitation, the orange

is output (either digital or analog, depending on the sensor), and the bare wire is ground.

Connect each end of the adapter cable to the corresponding color on the stripped cable. Plug

the adapter stereo connector to the ZSC (Section2.1).

Ground (bare)

Digital or analog

output (orange)

Power (brown)

Figure7 Pigtail wiring

NOTE: Some early adapters may have the older Decagon wiring scheme where the power supply is white, the output is

red, and the bare wire is ground.

After the sensor is properly connected to the pigtail adapter, follow the instructions in

Section2.1 to connect the adapter to the ZSC.

2.3 VIEWING SENSOR DATA

After connecting the ZSC and the sensor (Section2.1), the most recent scan of the

connected sensor will show on the screen (Figure8).

OPERATION

Figure8 Measurement screen

If the sensor is not automatically recognized, choose the sensor from the dropdown list

(Figure9).

Figure9 Select Sensor menu

ZSC

Swipe down to refresh the measurements as desired.

2.4 CHANGING SENSOR UNITS

The displayed sensor units can be changed at any time through the ZENTRA Utility

Preferences menu.

NOTE: Device Defaults in the Preferences menu do not apply to the ZSC. Defaults apply to METER data loggers only.

1. Select Preferences at the bottom of the Measurement screen (Figure10).

Figure10 Select Preferences

2. Select on the measurement of interest (Figure11).

Inhaltsverzeichnis

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung