METREL A 1355 Bedienungsanleitung
GPS Synchronization unit
A 1355
Instruction manual
Version 1.2, Code no. 20 751 793
2
Distributor:
Manufacturer:
METREL d.d.
Ljubljanska cesta 77
1354 Horjul
Slovenia
web site: http://www.metrel.si
e-mail: [email protected]
© 2013 METREL
Mark on your equipment certifies that this equipment meets the
requirements of the EU (European Union) concerning safety
and electromagnetic compatibility regulations.
No part of this publication may be reproduced or utilized in any form or by any means
without permission in writing from METREL.
A 1355 GPS Synchronization Unit Warnings
3
Table of contents
1WARNINGS..................................................................................................................3
2INTRODUCTION..........................................................................................................4
2.1MI 2892 POWER MASTER SYNCHRONIZATION ............................................................4
2.2MI 2792 /MI 2792A POWERQ4 PLUS SYNCHRONIZATION ..........................................5
3TYPICAL APPLICATIONS...........................................................................................7
3.1OBSERVING ON TWO OR MORE POINTS ON NETWORK...................................................7
4MAINTENANCE...........................................................................................................8
4.1INSPECTION .............................................................................................................8
4.2CLEANING ...............................................................................................................8
4.3SERVICE .................................................................................................................8
5TECHNICAL SPECIFICATIONS..................................................................................8
1 Warnings
To ensure a high level of operator's safety during using of GPS Synchronization unit the
following warnings have to be considered:
Do not use the device if any damage is noticed!
Consider all generally known precautions in order to avoid risk of electric
shock while dealing with electric installations!
If the GPS Synchronization unit is used in a manner not specified in this
Instruction manual, the provided protection can be impaired!
A 1355 GPS Synchronization Unit Introduction & Operation
4
2 Introduction
A 1355 GPS Synchronization unit guaranties that the time clock uncertainty of the Metrel
power quality analyzers does not exceed ±10 ms for 50 Hz signals, according to IEC
61000-4-30.
This performance is necessary to ensure that instruments produce the same aggregation
results when connected to the same signal. GPS Synchronization unit can only be used on
the MI 2892 Power Master, MI 2792 PowerQ4 Plus and MI 2792A PowerQ4 Plus
instrument.
The Global Positioning System (GPS) is a space-based global navigation satellite system
that provides reliable time information in all weather and at all times and anywhere on or
near the Earth when and where there is an unobstructed line of sight to one satellite. It is
maintained by the United States government which is solely responsible for its accuracy
and maintenance.
GPS Synchronization unit operation
On figure bellow main parts of GPS Synchronization unit are shown:
1. GPS receiver
2. Central threaded recess
(bottom side)
3. 5 meters of cable
4. PS/2 connector
Figure 1: Description of GPS Synchronization unit
2.1 MI 2892 Power Master Synchronization
In order to put device into work the following procedure should be followed:
1. Device unit should be placed outside of building. The GPS requires an open, clear view of
the sky. Buildings, covered parking areas, tunnels and dense foliage can cause the GPS
receiver to be unable to get correct time. Additionally unit can be secured with embedded
magnetic sticker or M3 screw.
Note: Make sure that the GPS Synchronization unit (including connection cable) is
not in contact with dangerous live voltage.
2. Connect PS/2 connector to MI 2892 Power Master instrument.
3. Go to General Setup menu Communication menu and set GPS – Enabled
Note: GPS cannot be enabled in RS-232 PC connection mode.
A 1355 GPS Synchronization Unit Introduction & Operation
5
Figure 2: Enable GPS module
4. Go to Setup Time & Date menu and select your time zone
Figure 3: Select Time zone
5. Status line on screen will notify user about current GPS status.
GPS detected GPS module detected, position not valid or no
satellite GPS signal reception.
GPS time valid
GPS module detected, satellite GPS signal
reception, date and time valid and synchronized,
synchronization pulses active
Note: After GPS plug in, device can take up to few minutes to synchronize with satellite.
Power Master is now synchronized and ready for measurements (recordings) according to
the IEC 61000-4-30.
2.2 MI 2792 / MI 2792A PowerQ4 Plus Synchronization
In order to put device into work the following procedure should be followed:
1. Device unit should be placed outside of building. The GPS requires an open, clear
view of the sky. Buildings, covered parking areas, tunnels and dense foliage can
cause the GPS receiver to be unable to get correct time. Additionally unit can be
secured with embedded magnetic sticker or M3 screw.
Note: Make sure that the GPS Synchronization unit (including connection cable) is
not in contact with dangerous live voltage.
2. Connect PS/2 connector to PowerQ4 Plus instrument.
3. PowerQ4 Plus status line on MAIN MENU will notify user about current GPS status.
A 1355 GPS Synchronization Unit Introduction & Operation
6
GPS detected GPS module detected, position not valid or no
satellite GPS signal reception.
GPS time valid
GPS module detected, satellite GPS signal
reception, date and time valid and synchronized,
synchronization pulses active
Note: After GPS plug in, device can take up to few minutes to synchronize with satellite.
Once GPS is synchronized with satellites instrument will demand from the user to set the
correct time zone (date and hour), as shown on figure below.
Figure 4: Setting the time zone (hour)
Use keys to select correct time zone (hour) and confirm selection with
key.
PowerQ4 Plus is now synchronized and ready for measurements (recordings) according to
the IEC 61000-4-30.
A 1355 GPS Synchronization Unit Typical applications
7
3 Typical applications
3.1 Observing on two or more points on network
By using two or more synchronized instruments by means of GPS unit, user can perform
simultaneous measurement on the different network points. GPS unit assures that
instruments are synchronized during EN 50160 surveys. Additionally same configuration
can be used for troubleshooting, for example to estimate disturbance impact on network or
susceptible load. The following figure shows instrument placement in that case. PowerQ4
Plus instruments are placed on:
- motor - source of disturbance (aggressor),
- server room (victim) – victim of disturbance
- transformer –path of disturbance spreading into network
By using instruments recorders (transient, inrush and waveform) and PowerView software
user can observe disturbance spreading over the network and estimate impact under
various conditions.
Figure 5: Distributed network measurement
A 1355 GPS Synchronization unit Technical Specifications
8
4 Maintenance
4.1 Inspection
To maintain operator safety and ensure reliability of the GPS Synchronization unit it is good
practice to inspect it on a regular basis. Check that the enclosure and optional connection are
without defects such as scratches or breaks.
4.2 Cleaning
Use a soft cloth moistened with soapy water or alcohol to clean the surface of a device and
leave it to dry totally before using it.
Warning:
Do not use liquids based on petrol or hydrocarbons!
4.3 Service
There are no user serviceable parts. For repairs under or out of warranty time please contact
your distributor for further information.
5 Technical Specifications
Dimensions 67 mm x 19 .5mm (Φx h)
Weight < 200 g
IP 67
Cable length 5 m
Power consumption 100mA @ 5V
Receiver sensitivity -185 dBW
Operating temperature -30
0
C ÷ 80
0
C
Storage temperature -40
0
C ÷ 90
0
C
Satellite acquisition time 45 s
Time accuracy ±10 ms
Mounting Embedded magnetic sticker
4 mm central deep recess for M3 screw
Connector PS/2 male
Inhaltsverzeichnis
Andere METREL GPS Handbücher
