MFJ MFJ-422B Bedienungsanleitung

MFJ-422B/422B-X INSTRUCTIONS

INTRODUCTION

Thank you for your purchase of the MFJ-422B/422B-X Electronic Keyer.

The MFJ-422B/422B-X is designed to mount on the "BENCHER" paddle

resulting in a compact, one-piece Keyer/Paddle combination. The improved

Curtis 8044 ABM Keyer IC is used in the MFJ-422B/422B-X to make perfect

code transmission easy and pleasant. Controls are located for easy

access while operating.

CONTROLS

1. VOLUME: Adjust the volume of the sidetone from the internal speaker.

Functions as the power ON/OFF switch for the MFJ-422B/422B-X.

2. SPEED: Varies the sending speed from 8 to 50 WPM.

3. AUTO/SEMI-AUTO: AUTO-Normal operating position. Dots and dashes of

the correct length are generated automatically.

SEMI-AUTO:-Dots are generated automatically. Dashes are manually

made. (NOTE: In this position, when the dash paddle is held your

transmitter is continuously for tuning.)

4. TONE: Sets the pitch of the sidetones. This control is recessed

inside the cabinet between the VOLUME and SPEED controls. A small

flat head screwdriver is needed for adjustment.

5. WEIGHT: Adjusts dot and dash lengths. When turned fully counter-

clockwise, dot-dash-space ratio is a perfect 1:3:1. This control is

located on the rear of the cabinet and is also recessed. A small flat

head screwdriver is necessary for adjustment. (NOTE: The weight

control is factory set for a 1:3:1 ratio.)

INSTALLATION

FOR MFJ-422B (KEYER WITH PADDLE)

If you purchased the MFJ-422B (Keyer with Paddle), the keyer will

come factory installed on the paddle and the only connections necessary

will be to your transmitter and power supply if used.

If battery operation is desired, remove the rubber foot on the

bottom rear of the paddle and screw holding the plastic wire clamp from

the bottom center of the paddle. The keyer will now slide off the paddle

base toward the rear. Install a 9V transistor battery in the battery

snap and slip the battery into the holder. Reverse the above procedure

to re-install the keyer onto the paddle. Feed the connecting cable

through the slot on the bottom of the paddle and is clamped securely with

the cable clamp. (NOTE: Long-life Alkaline type batteries are recommended

for longest uninterrupted operation.)

FOR MFJ-422B-X (KEYER WITHOUT PADDLE)

If you purchased the MFJ-422B-X (Keyer without Paddle) for

connection to your own "BENCHER" paddle, follow the procedure below for

proper connection.

1. Remove the rubber foot from the bottom rear of your "BENCHER" paddle.

2. Remove the plastic cable clamp from the bottom center of the paddle.

3. Solder the shield on the cable from the MFJ-422B-X to the solder lug

located between the rear rubber foot and the cable clamp on the bottom

of the paddle.

4. Solder the red wire in the cable from the MFJ-422B-X to the solder lug

on the dot post of the paddle and the white wire to the solder lug on

the dash post.

5. If battery operation is desired, install a 9V transistor battery in

the battery snap in the MFJ-422B-X and slip the battery into the

battery holder. (NOTE: Long-life Alkaline type batteries are

recommended for the longest uninterrupted operation.)

6. Replace the screw holding the rear rubber foot on the paddle with the

4-40 X 3/8" screw supplied with the MFJ-422B-X.

7. The MFJ-422B-X can now be slid onto the "BENCHER" paddle from the

rear. Feed the cable through the slot in the bottom right rear of the

box. Secure the box to the paddle by remounting the rear rubber foot

through the box to the paddle base. Fold the cable up neatly and

secure with the plastic cable clamp on the bottom of your "BENCHER"

paddle.

TRANSMITTER CONNECTION

(MFJ-422B/422B-X)

1. Provision is made for powering the MFJ-422B/422B-X with external 5-9V

DC supply. A subminiature POWER jack is located on the rear of the

MFJ-422B/422B-X for this purpose. An optional AC adapter is available

from the MFJ Enterprises, Inc. When a plug is inserted into the POWER

jack, the battery is automatically disconnected. Use an adapter with

a 2.5 mm phone plug with the tip being positive.

2. Connect a shielded cable from the KEYING OUTPUT of the MFJ-422B/422B-X

to your transmitter. Consult the instructions for your transmitter to

determine whether to use the "Direct" or "Grid block" output jack.

(NOTE: If in doubt as to which jack to use, try both jacks. If the

transmitter keys continuously when the cable is plugged into one jack,

use the other one.)

OPERATION

After proper connection of the MFJ-422B/422B-X you are ready for

operation. Rotate the VOLUME control clockwise to turn power on as

indicated by the LED light. Start sending with the paddle and adjust the

VOLUME, SPEED, TONE, and WEIGHT controls to your preference. (NOTE: If a

steady tone at high speed occurs, reduce the WEIGHT or the SPEED by

turning the respective control counter-clockwise.)

The dot and dash memory feature of the Curtis 8044 ABM IC makes

sending easier. This feature allows keying a dot before completion of a

dash or vice versa. This feature can be checked by setting the keyer to

the lowest speed and tapping first the dash paddle and then the dot

paddle before of the dash. The dash memory can be checked in a similar

manner. The dot insertion feature allows you to tap the dot paddle while

holding in the dash paddle. A dot will be insert automatically. The

dash insertion feature allows you to insert a dash while holding in the

dot paddle. With both paddles squeezed, the IAMBIC operation feature

allows sending of alternate dots and dashes. First paddle contact

determine whether a dot or a dash occurs first.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MFJ Industrieelektrik Handbücher

MFJ

MFJ MFJ-918 Bedienungsanleitung

Beliebte Industrieelektrik Handbücher anderer Marken

Rexroth Indramat

Rexroth Indramat DURADRIVE SYSTEM200 Technisches Handbuch

Abtech

Abtech HVJB Series Leitfaden

Murata

Murata GRM0335C1H8R1DA01 Series Bedienungsanleitung

SAF-HOLLAND

SAF-HOLLAND CBX 5415.5 Bedienungsanleitung

Eaton

Eaton Ulusoy HMH24-04 Bedienungsanleitung

Newlong

Newlong NP-7H Bedienungsanleitung

Murata

Murata GJM0335C1E4R4BB01 Series Bedienungsanleitung

Stahl

Stahl 8575/12 Bedienungsanleitung

SI Pegasus Bedienungsanleitung

Murata

Murata GRM1555C1H2R7CA01 Seies Bedienungsanleitung

Murata

Murata GRM0225C1E6R4BA03 Series Bedienungsanleitung

Cooper Power Systems

Cooper Power Systems VXE15 Bedienungsanleitung

S&C

S&C Vista SD Bedienungsanleitung

Murata

Murata GRM0335C2A7R3CA01 Series Bedienungsanleitung

Siemens

Siemens 3VA9988-0BM10 Bedienungsanleitung

Siemens

Siemens SITRANS LVS100 Bedienungsanleitung

Murata

Murata GRM32ER60G227ME05 Series Bedienungsanleitung

Siemens

Siemens SENTRON SUPERSWITCH 3KL82 Series Bedienungsanleitung