MG Mini-M M2PDU Bedienungsanleitung
EM-5166 Rev.1 P. 1 / 4
MG CO., LTD. www.mgco.jp
5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
INSTRUCTION MANUAL
Mini-M™
PULSE DIVIDER MODEL M2PDU
BEFORE USE ....
Thank you for choosing us. Before use, please check con-
tents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact our sales office or representatives.
■PACKAGE INCLUDES:
Signal conditioner (body + base socket).............................(1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■POWER INPUT RATING & OPERATIONAL RANGE
• Locate the power input rating marked on the product and
confirm its operational range as indicated below:
85 – 264V AC rating: 85 – 264V, 47 – 66 Hz, approx. 4 - 6 VA
24V DC rating: 24V ±10%, approx. 2 W
11 – 27V DC rating: 11 – 27V, approx. 2 W
110V DC rating: 85 – 150V, approx. 2 W
■GENERAL PRECAUTIONS
• Before you remove the unit from its base socket or mount
it, turn off the power supply and input signal for safety.
■ENVIRONMENT
• Indoor use.
• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -5 to +55°C
(23 to 131°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.
• Be sure that the ventilation slits are not covered with ca-
bles, etc.
■WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.
• With voltage output, do not leave the output terminals
shortcircuited for a long time. The unit is designed to
endure it without breakdown, however, it may shorten ap-
propriate life duration.
COMPONENT IDENTIFICATION
Model
Body Base Socket
Connection
Diagram
Specifications
Fixing Screw
M2PDU
EM-5166 Rev.1 P. 2 / 4
MG CO., LTD. www.mgco.jp
5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
INSTALLATION
Loosen the fixing screw at the front of the unit in order to
separate the body from the base socket.
DIN Rail
35mm wide
Spring Loaded
DIN Rail Adaptor
■DIN RAIL MOUNTING
Set the base socket so that
its DIN rail adaptor is at
the bottom. Position the
upper hook at the rear side
of base socket on the DIN
rail and push in the lower.
When removing the socket,
push down the DIN rail
adaptor utilizing a minus
screwdriver and pull.
■WALL MOUNTING
Refer to “EXTERNAL DIMENSIONS.”
COMPONENT IDENTIFICATION
Setting SW A
Setting SW B
Setting SW C
Division Ratio Setting
Rotary SW
Setting SW D
■FRONT VIEW
Division Ratio
In the range of 1/1 to 1/6400, division ratio can be set arbi-
trarily with the following combinations of the switches.
Switch No. Switch A Switch B Switch C Switch D
1 No divi-
sion
No divi-
sion
No divi-
sion
No divi-
sion
2 1/2 1/16 1/128 1/5
3 1/4 1/32 1/256 1/25
4 1/8 1/64 - -
Note 1. Set two switches out of A through C to "no division".
(Settings such as 1/2 for switch A and 1/16 for switch B
are disabled. )
Note 2. 1/5 and 1/25 are not settable.
Be sure to set Switch A through C when setting Switch
D to 1/5 or 1/25.
Division setting list
(*) factory default setting
Division
ratio Switch A Switch B Switch C Switch D
No division (*)
1111
1/2 2 1 1 1
1/4 3 1 1 1
1/8 4 1 1 1
1/10 2 1 1 2
1/16 1 2 1 1
1/20 3 1 1 2
1/32 1 3 1 1
1/40 4 1 1 2
1/50 2 1 1 3
1/64 1 4 1 1
1/80 1 2 1 2
1/100 3 1 1 3
1/128 1 1 2 1
1/160 1 3 1 2
1/200 4 1 1 3
1/256 1 1 3 1
1/320 1 4 1 2
1/400 1 2 1 3
1/640 1 1 2 2
1/800 1 3 1 3
1/1280 1 1 3 2
1/1600 1 4 1 3
1/3200 1 1 2 3
1/6400 1 1 3 3
M2PDU
EM-5166 Rev.1 P. 3 / 4
MG CO., LTD. www.mgco.jp
5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
TERMINAL CONNECTIONS
Connect the unit as in the diagram below or refer to the connection diagram on the side of the unit.
■EXTERNAL DIMENSIONS unit: mm [inch]
5
9
21.5 [.85]
70.5 [2.78]
86.7 [3.41]7.3 [.29] 15 [.59]
6 [.23]
59 [2.32]
DIN RAIL
35mm wide
(4 [.16])
8–M3
SCREW
72 [2.83]
23 [.91]
2–4.2x5
[.17x.20]
MTG HOLE
6 [.24] deep
116.7 [4.59]
• When mounting, no extra space is needed between units.
14
8
12
14 13
4 [.16]
■CONNECTION DIAGRAM
4kΩ
■ Mechanical Contact, Open Collector
or Clamp-on Pulse Sensor CLSP
Input Connection Examples
+12V
■ Voltage Pulse
+12V
■ Open Collector
Output Connection Examples
+
–
9
12
+
–
■ Voltage Pulse
+
–
9
12
+
–
+
+
–
–
PWR
+
+
–
–
PWR
+
–
1
4
+5
+
–
1
4
+5
+
–
OUTPUT
9
12
U(+)
V(–)
POWER
13
14
+
–
INPUT
1
5
4
+
SENSOR EXCITATION
M2PDU
EM-5166 Rev.1 P. 4 / 4
MG CO., LTD. www.mgco.jp
5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
WIRING INSTRUCTIONS
■SCREW TERMINAL
Torque: 0.8 N·m
■SOLDERLESS TERMINAL
Refer to the drawing below for recommended ring tongue
terminal size. Spade tongue type is also applicable.
Applicable wire size: 0.25 to 1.65 mm2(AWG 22 to 16)
Recommended manufacturer: Japan Solderless Terminal
MFG.Co.Ltd, Nichifu Co.,ltd
6 (.24) max
3.3 (.13) max
mm (inch)
CHECKING
1) Terminal wiring: Check that all cables are correctly con-
nected according to the connection diagram.
2) Power input voltage: Check voltage across the terminal
13 – 14 with a multimeter.
3) Input: Check that the input frequency is 30 Hz or less for
relay contact, 100 kHz or less for other types of input.
Check also that the input pulse is of 10 msec. or wider for
relay contact, 5 µsec. or wider for other types of input.
4) Output: Check that the load resistance meets the de-
scribed specifications as shown below.
OUTPUT LOAD REQUIREMENTS
Open collector 50V DC @ 100mA max.
Voltage pulse
250Ω min. for 5V
600Ω min. for 12V
1200Ω min. for 24V
LIGHTNING SURGE PROTECTION
We offer a series of lightning surge protector for protec-
tion against induced lightning surges. Please contact us to
choose appropriate models.
Andere MG E/A-System Handbücher
MG
MG R5-SV1A Bedienungsanleitung
MG
MG R7F4DC-DAC16C-H Bedienungsanleitung
MG
MG DLS-M1 Bedienungsanleitung
MG
MG R7F4HD-DA32B Bedienungsanleitung
MG
MG Devicenet R7F4HD-DC32B Bedienungsanleitung
MG
MG R7F4DC-DC8A-J Bedienungsanleitung
MG
MG R7K4FML3-6-DC32B Bedienungsanleitung
MG
MG R7F4HEIP-DA16A Bedienungsanleitung
MG
MG M2BS-16U2 Bedienungsanleitung
MG
MG Devicenet R7F4DD-DA16B-H Bedienungsanleitung
MG
MG R7F4HD-DAC32C Bedienungsanleitung
MG
MG Devicenet R7F4HD-DA32A Bedienungsanleitung
MG
MG R5-DS1A Bedienungsanleitung
MG
MG R6N-SS2 Bedienungsanleitung
MG
MG R7I4DML3-DC32A Bedienungsanleitung
MG
MG R7F4DH-1-DAC16B Bedienungsanleitung
MG
MG R7I4DECT-1-DC32A Bedienungsanleitung
MG
MG R3-DA16 Bedienungsanleitung
MG
MG R6D-SV2 Bedienungsanleitung
MG
MG DLC E2 Series Bedienungsanleitung
Beliebte E/A-System Handbücher anderer Marken
WAGO
WAGO 750-344 Bedienungsanleitung
Teknim
Teknim TWM-1887 Bedienungsanleitung
Intelligent Appliance
Intelligent Appliance IA-2662-E Bedienungsanleitung
BERGHOF
BERGHOF ECC DIO 16/16 Bedienungsanleitung
Advantech
Advantech PCM-27J3AU Installations- und Betriebshandbuch
Festo
Festo CP-E08-M12-CL Bedienungsanleitung
