MG Mini-M M2VV Bedienungsanleitung

EM-5017 Rev.6 P. 1 / 2

MG CO., LTD. www.mgco.jp

5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

INSTRUCTION MANUAL

Mini-M™

VOLTAGE DIVIDER MODEL M2VV

BEFORE USE ....

Thank you for choosing us. Before use, please check con-

tents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact our sales ofﬁce or representatives.

■PACKAGE INCLUDES:

Signal conditioner (body + base socket).............................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■GENERAL PRECAUTIONS

• Before you remove the unit from its base socket or mount

it, turn off the input signal for safety.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -5 to +60°C

(23 to 140°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

• Be sure that the ventilation slits are not covered with ca-

bles, etc.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

COMPONENT IDENTIFICATION

Model

Body Base Socket

Connection

Diagram

Specifications

Fixing Screw

INSTALLATION

Loosen the ﬁxing screw at the front of the unit in order to

separate the body from the base socket.

DIN Rail

35mm wide

Spring Loaded

DIN Rail Adaptor

■DIN RAIL MOUNTING

Set the base socket so that

its DIN rail adaptor is at

the bottom. Position the

upper hook at the rear side

of base socket on the DIN

rail and push in the lower.

When removing the socket,

push down the DIN rail

adaptor utilizing a minus

screwdriver and pull.

■WALL MOUNTING

Refer to “EXTERNAL DIMENSIONS.”

M2VV

EM-5017 Rev.6 P. 2 / 2

MG CO., LTD. www.mgco.jp

5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the connection diagram on the side of the unit.

■EXTERNAL DIMENSIONS unit: mm (inch)

21.5 (.85)

70.5 (2.78)

84 (3.31)10 (.39) 15 (.59)

6 (.23)

59 (2.32)

DIN RAIL

35mm wide

[4 (.16)]

8–M3

SCREW

72 (2.83)

23 (.91)

2–4.2x5

(.17x.20)

MTG HOLE

6 (.24) deep

114 (4.49)

• When mounting, no extra space is needed between units.

14 13

4 (.16)

■CONNECTION DIAGRAM

–

OUTPUT

–

INPUT

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.8 N·m

■SOLDERLESS TERMINAL

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable.

Applicable wire size: 0.25 to 1.65 mm2(AWG 22 to 16)

Recommended manufacturer: Japan Solderless Terminal

MFG.Co.Ltd, Nichifu Co.,ltd

6 (.24) max

3.3 (.13) max

mm (inch)

LIGHTNING SURGE PROTECTION

We offer a series of lightning surge protector for protec-

tion against induced lightning surges. Please contact us to

choose appropriate models.

Andere MG E/A-System Handbücher

MG R1M-J3 Bedienungsanleitung

MG R7K4FML3-6-DC32A1 Bedienungsanleitung

MG R9WTU-ED Bedienungsanleitung

MG R7K4FML3-6-DAC32B Bedienungsanleitung

MG R7I4DML3-DC32A Bedienungsanleitung

MG R7F4DC-DAC16C-H Bedienungsanleitung

MG R5-SV1A Bedienungsanleitung

MG Devicenet R7F4DD-DA16B-H Bedienungsanleitung

MG 61C Bedienungsanleitung

MG R5-DS1A Bedienungsanleitung

MG R7F4HD-DA32B Bedienungsanleitung

MG R6N-SS2 Bedienungsanleitung

MG DLC-C1 Series Bedienungsanleitung

MG M6DBS Bedienungsanleitung

MG R1M-GH Bedienungsanleitung

MG R7F4HD-DAC32C Bedienungsanleitung

MG 10YS Bedienungsanleitung

MG R3-DA16 Bedienungsanleitung

MG R3Y-MS8 Bedienungsanleitung

MG R8-FS16N Bedienungsanleitung

MG R7F4DH-1-DAC16B Bedienungsanleitung

MG R7K4FML3-6-DA32-1 Bedienungsanleitung

MG R7F4HEIP-DA16A Bedienungsanleitung

MG M6DYV Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung