Miboxer D1-CX Bedienungsanleitung
Constant Voltage DMX512 & RDM Decoder
Model No.: D1-CX / D2-CX / D3-CX / D4-CX / D5-CX
Subordinate New Brand
Features
Function Settings
Parameter
Model No.
Output
Total Output
Input Voltage
Input Signal
Connection
Working Temp.
Model No.
Output
Total Output
Input Voltage
Input Signal
Connection
Working Temp.
D1-CX
20A/Channel
D1-CX
20A/Channel
D2-CX
10A/Channel
D2-CX
10A/Channel
D3-CX
6A/Channel
D3-CX
6A/Channel
D4-CX
5A/Channel
D4-CX
5A/Channel
D5-CX
4A/Channel
D5-CX
4A/Channel
-20~60°C-20~60°C
1. Accord with DMX512 standard protocol.
2. Digital Display, Set DMX initial address through button.
3. Support RDM function.
4. 2000hz/500hz Output PWM frequency is optional.
5. Logarithm/Linear dimming curve is optional.
6. Anti-reverse protection function
7. Short circuit&Overcurrent protection and recover function.
8. self-testing protection function when power on.
1.Digital Display status description
Self-locking: Get into locking state when there is no operation over 30 seconds, digital
display with low light or OFF.
Unlock: Long press M button 2 seconds to make digital display with high light, quit
self-locking state.
Address always ON: DMX signal valid.
Address flickering: DMX signal invaild.
Err: Short circuit/overcurrent protection; self-recover after 10 seconds.
2. DMX initial address setting
Under unlock status, when digital display show 001-512( for example ), Short press ▲button
or ▼buttom, you can change the DMX initial address; Long press, you can change it quickly.
For Example: Set Initial address to 100
3. System Parameter Setting Instruction
Parameter 1: PWM frequency setting(show or ; Short press ▲button or ▼
button to switch.
Under unlock status: Long press Mbutton 3 seconds to make digital display show or ,
then get into system parameter setting. By this time, short press Mbutton to switch 4 different
parameter setting circularly.
Set to PWM high frequency output, 2000Hz. (Factory default parameter)
Set to PWM low frequency output,500Hz.
Common anode
Max 20A Max 20AMax 18A
49mm 27mm
130mm
DC12~24V
DMX512, RDM
Parameter 2: Dimming Curve setting(Show or ), short press ▲button or ▼
button to switch.
Dimming curve is logarithm dimming. (Factory default parameter)
Dimming curve is linear dimming.
Parameter 3: Dimming smoothness setting(show or ), short press ▲button
or ▼button to switch.
Smooth dimming. (Factory defaut setting)
Standard dimming.
Exit system mode: long press M button 1 second to exit. Or it will be self exit if there is no
operation over 8 seconds.
Parameter 4: Digital display showing setting(show or ) short press ▲button
or ▼button to switch.
Under self-locking status, digital display always ON (low lighting showing). (Factory
default parameter)
Under self-locking status, digital display OFF.
D1-CX D2-CX D3-CX D4-CX D5-CX
Occupy 1 address
100
Occupy 2 address
100-101
Occupy 3 address
100-102
Occupy 4 address
100-103
Occupy 5 address
100-104
M
INPUT OUTPUT
CH1
M
INPUT OUTPUT
CH1 CH2
M
INPUT OUTPUT
CH2CH1 CH3
M
INPUT OUTPUT
CH1 CH2 CH3 CH4
M
INPUT OUTPUT
CH1 CH2 CH3 CH4 CH5
4. Restore factory default.
Under unlock status, long press Mbuttom 10 seconds until digital display show .
Logarithmic dimming curve Linear dimming curve
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
50 60 70 80 90 100
Brightness(%)
10 20 30 40
Gamma=1.6
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
50 60 70 80 90 100
Brightness(%)
10 20 30 40
Gamma=1.0
Dimming curve diagram
Connection diagram
Attention
Attention:
D1-CX D2-CX D3-CX D4-CX D5-CX
DMX512 Console
DMX512
Dimming
Panel
RGB LED Strip
v+
R
G
B
Color Temp. LED Strip
v+
W
C
Brightness LED Strip
v+
v-
RGB+CCT LED Strip
v+
R
G
B
C
W
RGBW LED Strip
v+
R
G
B
W
Power input
DC12V/24V
V- V+
Power input
DC12V/24V
V- V+
Power input
DC12V/24V
V- V+
Power input
DC12V/24V
V- V+
Power input
DC12V/24V
V- V+
1. This product should be debugged and installed by professionals.
2. Please check whether the output voltage of the power supply meets the requirements of
the product voltage range.
3. The product is not waterproof, please install it in the waterproof box when installed
outdoors.
4. Before switching on the power, please ensure that all wiring is correct, so as not to cause
damage to the devices。
5. If fault has occurred, non-professionals do not repair it without permission, otherwise the
devices will be damaged.
1. If the decoder is over 32pcs, or using the super long signal cable, you need DMX signal
amplifier. Amplify signal cannot be over 5 times.
2. If there is overshoot effect due to the long signal cable or low quality circuit, please
connect 0.25W 90-120Ω terminal resistance at the end of each DMX sigbal cable.
Made in China
RDM
DMX
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Andere Miboxer Medienkonverter Handbücher
