MicroBoards Technology G3 Auto Printer Bedienungsanleitung

G3 Disc Publisher

For Mac OS X

Users Manual

Microboards Technology LLC Version 1.1

Any unauthorized modification to this equipment may result in the revocation by the FCC of the user’s authority to

operate this equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna

•Increase the separation between the equipment and antenna

•Connect the equipment into an outlet on a circuit different than that to which the receiver is connected

•Consult the dealer or an experienced radio/TV technician for help

This product is in conformity with the EMC Directive (89/336/EEC) through compliance with the following European standards: EN 55022,

EN 55024. The CE mark has been affixed in accordance with the CE Marking Directive 93/68/EEC.

Canadian Department of Communications (DOC) Statement

This Class B digital apparatus complies with the Canadian ICES-003 Issue 4:2004. Cet appareil numerique de la classe B est conforme a la

norme NMB-003 du Canade

MICROBOARDS TECHNOLOGY, LLC G3 DISC PUBLISHER

TABLE OF CONTENTS

Introduction .......................................................................................................................... 5

What’s Included.................................................................................................................5

System Requirements....................................................................................................... 6

Assembly and Installation..................................................................................................... 6

Assembly Instructions ....................................................................................................... 6

G3 Disc Publisher Assembly.......................................................................................... 6

Installing Ink Cartridges..................................................................................................... 7

Supported Ink Cartridges ............................................................................................... 7

Loading / Replacing Ink Cartridges ................................................................................ 7

Loading Discs.................................................................................................................... 8

Front Control Panel........................................................................................................... 8

Installation of Drivers and Software................................................................................... 9

Driver and Microboards PrintWrite Installation ............................................................... 9

Connecting to a Mac ......................................................................................................... 9

Adding the G3 Printer..................................................................................................... 9

Printer Alignment................................................................................................................ 10

Alignment........................................................................................................................ 10

Microboards Toolbox.......................................................................................................... 10

Ink Level.............................................................................Error! Bookmark not defined.

Test................................................................................................................................. 11

Clean............................................................................................................................... 11

Utility ..................................................................................Error! Bookmark not defined.

Support............................................................................................................................ 12

Register........................................................................................................................... 12

The G3 Disc Publisher and PrintWrite................................................................................ 12

Print Only without PrintWrite .............................................................................................. 13

Troubleshooting ................................................................................................................. 13

Printer not printing:.......................................................................................................... 13

Disc Loading error........................................................................................................... 13

Low Ink indication............................................................................................................ 13

Printing Specifications........................................................................................................ 14

Technical Support .............................................................................................................. 14

MICROBOARDS TECHNOLOGY, LLC G3 DISC PUBLISHER

Introduction

The Microboards G3 Disc Publisher is a single drive, 50 disc, print and record system. The G3 combines

professional quality printing and recording into a single, easy to use duplicator. The system includes one 24x

DVD recorder. Microboards and HP co-developed the printer technology, allowing up to 4800 x 1200 dpi

printing. The Microboards PrintWrite software is a dynamic interface for both beginners and power users.

Easily record DVD Video, DVD data, Audio CD’s, Data CD’s, Video CD’s and much more.

Other features include:

•Asynchronous print and record function

•Creation of audio CD’s from MP3 or wave files

•Batch mode, allowing multiple different masters to be used at a time.

•Integrated print function.

•A cover flow of your recently-used images used for printing.

•Multi-job queueing.

What’s Included

When unpacking your G3 Disc Publisher system, the following items should be included:

•G3 Disc Publisher print and record system

•G3 Disc Publisher Quick Start Guide

•Power Cord

•Blank Printable CDs

•Users Manual (This document)

•Microboards G3 Disc Publisher Install CD (Includes drivers and Microboards PrintWrite

software)

•Microboards GX-300HC Color Ink cartridge (14ml)

•USB Printer Cable

•Input Bin rods (already installed)

•50 disc output assembly

If any of these items are missing, please contact your distributor or Microboards Technology

Technical Support department at 952-556-1639.

System Requirements

The Microboards G3 Disc Publisher has the following minimum requirements and compatibilities:

Operating System

Mac OS 10.5

Processors

Intel Processor is required

System Memory

Minimum 1 GB of system memory

Hard Drive

A separate internal 7200 RPM hard drive is recommended for storing your data. Using the same

hard drive as the operating system can cause the system to perform slowly.

USB Connection

USB 2.0 is required. USB 1.1 is not supported, as using USB 1.1 will result in significantly longer

recording times and the potential for recording failures.

Assembly and Installation

Assembly Instructions

G3 Disc Publisher Assembly

Remove the G3 Disc Publisher

system from the shipping box and

confirm you received all of the

items.

Place the G3 Disc Publisher on a

stable, flat surface. You will need

room both in front and behind the

system, as discs will be accessed

from both locations.

The Input Bin posts are pre-

installed, with the wide post to the

right.

The 50-disc Output Bin is shipped in

place under the front cover. Lift the

cover to remove the packaging tape

from the Output Bin.

MICROBOARDS TECHNOLOGY, LLC G3 DISC PUBLISHER

Installing Ink Cartridges

Supported Ink Cartridges

The G3 Disc Publisher uses a single color ink cartridge. The part number for this cartridge is GX-

300HC. If other cartridges are installed, the G3 Disc Publisher will not function. These cartridges are

available from any Microboards reseller.

Refill kits or non-Microboards ink cartridges are not recommended for use in the G3

Disc Publisher system. Use of these types of cartridges will cause the printer to fail

and will void the warranty.

Loading / Replacing Ink Cartridges

Cartridges should be changed while the G3 Disc Publisher is on. The cartridge can be replaced

during printing.

The G3 Disc Publisher system ships with one Microboards GX-300HC color ink cartridge.

•Lift the front cover with the power on. The ink cartridge cradle will move to the right side of

the G3 Disc Publisher, as shown below.

•Tilt the old cartridge forward to release the cartridge from the cradle, as shown in the inset

below.

•Lift the old cartridge out of the cradle.

•Remove the new GX-300HC ink cartridge from its packaging and carefully remove the plastic

tape. Hold the ink cartridge so that the copper strip is at the bottom.

•With the front of the new GX-300HC ink cartridge tilted down, slide the cartridge into the

cradle.

•Tilt the front of the GX-300HC ink cartridge back up to lock the ink cartridge in place.

•Lower the front cover.

•The new GX-300HC ink

cartridge will be initialized

by the printer.

The Microboards GX-300HC

Ink Cartridge must be used

or the printer will not

function.

Power Button

Cancel Button

Ink Light

Media Light

Power/Activity

Light

Loading Discs

The next step is to load your G3 Disc Publisher with discs. The system will accept CD or DVD 120

mm (12 cm) inkjet printable discs. If the disc does not have an inkjet printable surface, the ink will not

adhere to the surface of the disc. The G3 Disc Publisher will only accept 12 cm discs. Business card

or 8 cm discs are not supported by this system.

Figure 1 Figure 2

Load the first 5 or 6 discs flat, as seen in figure 1.

Load the rest of the discs at an angle, against the wide input rod, as seen in figure 2.

The G3 Disc Publisher will hold a maximum of 50 discs. DO NOT load more than 50 discs in the

system, as this may cause the discs to feed incorrectly.

Front Control Panel

The AC power switch located on the back of the G3 Disc Publisher must be turned on first in order to

supply power to the Front Control Panel.

The Power Button on the front panel of the G3 Disc Publisher turns the G3 Disc Publisher Printer on

and off. It may take a few seconds for the G3 Disc Publisher Printer to turn on after you press the

Power Button. This does not affect power to the drive within the G3 Disc Publisher.

To turn off the power to the printer using the Control Panel, you will need to press and hold the Power

Button for 3 seconds. Once the Ink Light, Media Light, and Power Light begin flashing, you can

release the Power Button.

The green Power/Activity light flashes when the printer is active, either while printing or initializing.

The Cancel Button can be used to discontinue printing. When using PrintWrite, this will only affect

the current disc being printed. If printing through other applications, this will either cancel the entire

print job or just the current disc depending on the label being printed and the application being used.

Any disc being printed when the Cancel button is pressed will be ejected into the Output bin.

If a disc is not detected

during printing, the Media

Light will flash. Verify that

you have discs in the input

hopper and press the Media

Light to load and print the

next disc.

The Ink Light will come on if

the ink cartridge is low or

empty.

MICROBOARDS TECHNOLOGY, LLC G3 DISC PUBLISHER

Installation of Drivers and Software

Driver and Microboards PrintWrite Installation

Drivers and Microboards PrintWrite must be installed on a hard disk. Once you have installed the

software, store the original installer disc in a safe place.

1. Insert the Installation CD in your system’s disc drive. Open the disc icon when it appears on

the desktop.

2. Double-click on the Microboards Publisher.mpkg icon. Follow the on-screen instructions,

read and agree to the end user license agreement.

3. When prompted, enter your administrator password.

4. When prompted, click Install. Once the Microboards Installer has completed, a restart is

required.

Connecting to a Mac

DO NOT CONNECT YOUR G3 DISC PUBLISHER BEFORE RUNNING THE INSTALLER

LOCATED ON THE INSTALLATION DISK!!

The connection between the Mac and the Microboards G3 Disc Publisher is done with one USB 2.0

cable.

1. Plug in the AC power cord to the back of the G3 Disc Publisher.

2. Confirm that the power is turned ON to both the G3 Disc Publisher and on your Mac.

3. Connect the square shaped end of the USB cable to the back of the G3 Disc Publisher.

4. Connect the flat, rectangular end of the USB cable into a USB 2.0 port in

your Mac.

Adding the GX Series Printer

Once the drivers and software have been installed and the G3 connected, the GX

Series Printer needs to be added.

1. Click System Preferences in the Dock.

2. Select Print & Fax. If the GX Series printer has not been added

automatically, then click the Add or + button to add a printer.

3. Select GX Series from the list and click the Add button.

4. Once the GX Series Printer has been added, it will appear in the

available printers list, as shown below.

Docked

Utility Icon

Printer Alignment

Verify the printer alignment the first time you use the Publisher. You may need to align your

printer before the printed images will be centered on your media. Changing the brand or type

of media you are using may also require small alignment adjustments.

Alignment

•Click System Preferences in the Dock.

•Select Print & Fax.

•Double-click the Microboards GX Series icon.

•Click the Printer Setup button.

•Click the Utility button to open the

Microboards Toolbox.

•Click the Open Printer Utility

button.

•Click the Disc Printing icon.

•Enter the alignment changes into the

Top and Left Side boxes. These

settings will change the size of the

top and left margins, respectively.

Decreasing the values will move the

image up or to the left, increasing will

adjust down or to the right.

•Click the Apply Now button.

•Verify the alignment by printing a full coverage image. The image should print centered on

the disc. If not, adjust the Top and Left Side alignment values according to the graphic on

the Alignment tab and repeat.

Microboards Utility

Access the Microboards Utility by selecting the System Preferences from the Dock.

Select Print & Fax. Highlight the Microboards GX Series icon and click the Utility icon.

You can also select Open Printer Utility from the Utilities menu in PrintWrite. The

Utility will allow you to access the Printer information as shown below.

Andere Handbücher für G3 Auto Printer

Inhaltsverzeichnis

Andere MicroBoards Technology Disc-Duplikator Handbücher

MicroBoards Technology

MicroBoards Technology PF-2 PrintFactory Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology MX SERIES Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology CX-1 Publisher Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology QD-123 Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology DVD Premium Series Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology GX-1 Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology G3 Auto Printer Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology DX-2 Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology CX-1 Publisher Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology QD-DVD 123 Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology DVD Premium Pro Series Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology CWR-424-52 Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology StartREC Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology GX-2 Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology GX Disc Printer Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology QD-DVD Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology PrintFactory PF-3 Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology GX-2 Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology CX-1 Publisher Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology DX-2 Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology CopyWriter Pro-452RM Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology Micro Orbit Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology CX-1 Publisher Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology CopyWriter Series Bedienungsanleitung

Beliebte Disc-Duplikator Handbücher anderer Marken

Riso

Riso CV Series Handbuch

Addonics Technologies

Addonics Technologies HDUS325DX Bedienungsanleitung

Carry

Carry Pro118 Bedienungsanleitung

CopyPro

CopyPro PowerPro II Bedienungsanleitung

Primera

Primera Max Bedienungsanleitung

Logicube

Logicube EchoPlus-NG Bedienungsanleitung

Silca

Silca Delta 2000 SA Bedienungsanleitung

Reflex7

Reflex7 Daisy Chain Series Bedienungsanleitung

Vinpower Digital

Vinpower Digital SharkCopier DC Bedienungsanleitung

Codonics

Codonics Virtua E Bedienungsanleitung

Octave

Octave Copy Master II Bedienungsanleitung

Kanguru

Kanguru U2-DVDDUPE-S Bedienungsanleitung

StarTech.com

StarTech.com 8STSATDUP11 Bedienungsanleitung

DUPLO SEIKO CORPORATION

DUPLO SEIKO CORPORATION Duprinter DP-460 Bedienungsanleitung

Addonics Technologies

Addonics Technologies UDFH7 Bedienungsanleitung

Vinpower Digital

Vinpower Digital MiniLoader VDX-1 Bedienungsanleitung

Addonics Technologies

Addonics Technologies CFASTD5 Bedienungsanleitung

Telex

Telex SpinWise Bedienungsanleitung