MicroBT Whats Miner M10 Bedienungsanleitung
1
Whats Miner M10 Operation
Guide
V1.1（Simplified Version)
Shenzhen MicroBT Electronics
Technology Co.,Ltd
2
1. M10 Product Introduction............................................................................................................ 3
2.Whats Miner Connection and Racking Safety Notes..................................................................... 3
2.1.Miner Connection Notes.....................................................................................................3
2.1.1.Power Supply Control Wire Connection Notes........................................................4
2.1.2.Adapter Board Control Wire Connection Notes...................................................... 4
2.1.3.Fan Connection Notes..............................................................................................6
2.1.4.Hash Board and Adapter Board Connection Notes................................................. 7
2.1.5.Power Supply Copper Busbar Connection Notes.....................................................9
2.1.6.Product Connection Check.....................................................................................10
2.2.Miner Handling and Racking Notes...................................................................................10
3. Miner Configuration Environment Preparation..........................................................................11
3.1.Miner Configuration Equipment List.................................................................................11
3.2.Miner Network Environment............................................................................................ 11
4.Miner Connection and Pre-Power Check.....................................................................................12
5.Miner Data Configuration（Configuration on the web page）..................................................13
5.1.Query the dynamic IP address obtained by the miner..................................................... 13
5.1.1.Run WhatsMinerTools software............................................................................ 13
5.1.2.Check the IP address Reported by the Miner........................................................ 14
5.2.Configuration Pool&Worker Data and NTP Server Address............................................. 16
5.2.1.Configuration Pool&Worker.................................................................................. 16
5.2.2.Modify the NTP Synchronization Server Address (optional)................................. 18
5.3.Configuration the Static IP Address (optional)................................................................. 19
5.4. Chinese and English Language Switching of Miner Page.................错误！未定义书签。
6.Miner Operation Status Check.....................................................................................................22
7.Miner Batch Data Configuration, Miner Status Check, Firmware Upgrade................................ 24
8.Miner Disassembly and Installation.............................................................................................24
8.1. Control Panel Disassembly and Installation.....................................................................24
8.1.1.Control Panel Disassembly.....................................................................................24
8.1.2.Control Panel Installation.......................................................................................26
8.2.Power Supply Disassembly and Installation..................................................................... 28
8.2.1.Power Supply Disassembly.....................................................................................28
8.2.2.Power Supply Installation...................................................................................... 29
8.3.Hash Board Disassembly and Installation......................................................................... 31
8.3.1.Hash Board Disassembly........................................................................................ 31
8.3.2.Hash Board Installation.......................................................................................... 33
3
1. M10 Product Introduction
Whats Miner M10
Bitcion Mining Magic
Product ParameterIntroduction as below：
HashRate：33TH/s ±5%
Chip：315pcs 16nm ASIC
Power：2145W±10%
Power Rate：65W/T ±10%
Power Supply：Whats Miner Power Supply P10（220v,2145W ±10%）
Control Panel：Own
Environment Temperature：-5℃~40℃
Product Size：390mm*130mm*220mm
2.Whats Miner Connection and Racking Safety
Notes
2.1.Miner Connection Notes
Check over the miner’s power supply control wire and adapter board control wire
and fan control wire to make sure connections are correct,the damage of control
board、hash board、transfer board、fan, etc. caused by incorrect connection will
4
not be covered by the warranty.
When connecting the wiring of the control board, the clasp must be corresponding,
and the pin cannot be inserted into the socket by force.If the backplug, the power may
burn the control board, burning the signal wire!
2.1.1.Power Supply Control Wire Connection Notes
The power control wire is 14pin, and the card slot is inserted relative:
Correct Connection：Incorrect Connection：
2.1.2.Adapter Board Control Wire Connection Notes
The adapter board control wire is 22pin, and the card slot is inserted relative:
Correct Connection：
5
Incorrect Connection：
6
2.1.3.Fan Connection Notes
The fan wire is 6pin, and the card slot is inserted relative:
Correct Connection：
7
Incorrect Connection：
2.1.4.Hash Board and Adapter Board Connection Notes
The socket of the adapter board and the pin of the hash board must be installed in
8
place to avoid other problems caused by contact problems!
Correct Connection：
Incorrect Connection：
9
2.1.5.Power Supply Copper Busbar Connection Notes
When the power supply copper busbar is connected to the hash board, the positive
and negative poles of the copper busbar cannot be connected incorrectly, and the
screw washers of the fixed copper bar must be aligned in parallel with the edge of
the copper bar. Otherwise, the machine may be short-circuited and burned when
the power is turned on, and the fixed screw must be fixed. Tighten to avoid the
machine not working properly due to poor contact with the copper bar!
Correct Connection：
Incorrect Connection：
10
2.1.6.Product Connection Check
After all the connections of the miner are connected and all the screws are tightened,
check again to confirm that the connection is correct.
2.2.Miner Handling and Racking Notes
In the process of handling and racking of the miner, it is strictly forbidden to use
the data cable, the power supply control wire and the fan wire as the load-
bearing handle of the miner, and to pick up the machine and the power supply.
Lifting the machine and power supply through the connection will result in
damage to the connection, loose connection, and physical damage to the control
panel beyond its capacity. The resulting hardware damage and malfunctions will
Inhaltsverzeichnis
