Microchip Technology PL360G55CF-EK Bedienungsanleitung
PL360G55CF-EK
PL360G55CF-EK Quick Start Guide
Overview
PL360G55CF-EK is an evaluation kit for the PL360 modem, a multi-protocol device to implement
standard and customized PLC solutions. PL360G55CF-EK includes a SAMG55 ARM® Cortex®-M4
microcontroller, which provides a full-featured platform to develop a complete communication system over
PLC technology.
Getting Started
Attention: Before starting, please obtain PL360G55CF-EK online resources from Microchip
website. Please follow the instructions of the welcome letter included with this kit.
Important: This guide assumes the use of 2 units of PL360G55CF-EK board running G3-PLC
PHY Tester.
Power-Up
The board can be supplied with the included USB cable or from an external DC Power Supply ranging
from 6V to 30V. When powered-up, LED 3V3 and LED 12V turn on. Please check the PL360G55CF-EK
User Guide to know more about the power supply requirements.
The kit comes already programmed with the G3-PLC PHY Tester for CENELEC-A application, allowing
the transmission and reception of PLC messages at PHY layer level. LED0 (green) blinks to indicate that
the application is running. LED1 (red) flashes when a PLC message is received and LED D104 (yellow)
will flash at each transmission.
Running PHY Tester Demo
Figure 1. PLC Test Setup
1. Download Microchip PLC PHY Tester from the online resources site and install it
© 2019 Microchip Technology Inc. User Guide DS50002866A-page 1
2. Power-up PL360G55CF-EK board #1 connecting it to a PC using the included micro USB cable
3. Launch the PHY Tester PC Tool, select the serial COM port assigned to board #1 and 230400bps
for the baud rate
4. Follow on-screen instructions to configure a Tx test
5. Power-up PL360G55CF-EK board #2 connecting it to a PC using the included micro USB cable
6. Launch the PHY Tester PC Tool, select the serial COM port assigned to board #2 and 230400bps
for the baud rate
7. Follow on-screen instructions to configure an Rx test
8. Start Rx test in PL360G55CF-EK board #2
9. Start Tx test in PL360G55CF-EK board #1
10. Transmitted frames from board #1 are received in board #2
For more information about usage and configuration of the PLC PHY Tester Tool, please check the user
manual embedded in the tool: Help tab > User Manual.
Navigating the Kit
Important: In order to explore all the features of this kit, please check the firmware user
guides provided with the online contents of the EK.
Online Resources
PL360G55CF-EK is complemented with a set of online resources. To access these resources, please
follow the procedure described in the welcome letter. These online resources include:
• Board schematics, PCB layout and Bill of Materials
• Last version of supported firmware stacks for Power Line Communications
• Set of PC tools to evaluate the performance of Microchip PLC solutions
Firmware Projects
PL360G55CF-EK currently supports G3-PLC and PRIME protocols. Each firmware stack includes several
projects and examples of use. For more information about the firmware projects and how to build and
debug the different examples, please read the corresponding documentation provided with the online
contents of the kit:
•G3-PLC Firmware Stack
•PRIME 1.3 FW Stack for Service Nodes and PRIME 1.3 FW Stack for Base Nodes
•PRIME 1.4 FW Stack for Service Nodes and PRIME 1.4 FW Stack for Base Nodes
Tools
Some of the projects included in the firmware releases require an external PC application:
• G3-PLC/PRIME Manager PC Tool: enables users to easily interface with the top layer of the provided
PLC stacks
• PHY Tester Tool: provides complete access to PHY layer configuration and utilization. Excellent tool
for point-to-point tests
• PHY Sniffer: captures, analyzes and displays PLC traffic. Excellent tool for network supervision and
debugging
PL360G55CF-EK
© 2019 Microchip Technology Inc. User Guide DS50002866A-page 2
For more information about the tools, please read the documentation of the firmware stack.
Revision History
Revision Date Description
Document 03/2019 Initial Release
PL360G55CF-EK
© 2019 Microchip Technology Inc. User Guide DS50002866A-page 3
The Microchip Web Site
Microchip provides online support via our web site at http://www.microchip.com/. This web site is used as
a means to make files and information easily available to customers. Accessible by using your favorite
Internet browser, the web site contains the following information:
•Product Support – Data sheets and errata, application notes and sample programs, design
resources, user’s guides and hardware support documents, latest software releases and archived
software
•General Technical Support – Frequently Asked Questions (FAQ), technical support requests, online
discussion groups, Microchip consultant program member listing
•Business of Microchip – Product selector and ordering guides, latest Microchip press releases,
listing of seminars and events, listings of Microchip sales offices, distributors and factory
representatives
Customer Change Notification Service
Microchip’s customer notification service helps keep customers current on Microchip products.
Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata
related to a specified product family or development tool of interest.
To register, access the Microchip web site at http://www.microchip.com/. Under “Support”, click on
“Customer Change Notification” and follow the registration instructions.
Customer Support
Users of Microchip products can receive assistance through several channels:
• Distributor or Representative
• Local Sales Office
• Field Application Engineer (FAE)
• Technical Support
Customers should contact their distributor, representative or Field Application Engineer (FAE) for support.
Local sales offices are also available to help customers. A listing of sales offices and locations is included
in the back of this document.
Technical support is available through the web site at: http://www.microchip.com/support
Microchip Devices Code Protection Feature
Note the following details of the code protection feature on Microchip devices:
• Microchip products meet the specification contained in their particular Microchip Data Sheet.
• Microchip believes that its family of products is one of the most secure families of its kind on the
market today, when used in the intended manner and under normal conditions.
• There are dishonest and possibly illegal methods used to breach the code protection feature. All of
these methods, to our knowledge, require using the Microchip products in a manner outside the
operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is
engaged in theft of intellectual property.
• Microchip is willing to work with the customer who is concerned about the integrity of their code.
PL360G55CF-EK
© 2019 Microchip Technology Inc. User Guide DS50002866A-page 4
• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their
code. Code protection does not mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the
code protection features of our products. Attempts to break Microchip’s code protection feature may be a
violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software
or other copyrighted work, you may have a right to sue for relief under that Act.
Legal Notice
Information contained in this publication regarding device applications and the like is provided only for
your convenience and may be superseded by updates. It is your responsibility to ensure that your
application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY
OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS
CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE.
Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life
support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend,
indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting
from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual
property rights unless otherwise stated.
Trademarks
The Microchip name and logo, the Microchip logo, AnyRate, AVR, AVR logo, AVR Freaks, BitCloud,
chipKIT, chipKIT logo, CryptoMemory, CryptoRF, dsPIC, FlashFlex, flexPWR, Heldo, JukeBlox, KeeLoq,
Kleer, LANCheck, LINK MD, maXStylus, maXTouch, MediaLB, megaAVR, MOST, MOST logo, MPLAB,
OptoLyzer, PIC, picoPower, PICSTART, PIC32 logo, Prochip Designer, QTouch, SAM-BA, SpyNIC, SST,
SST Logo, SuperFlash, tinyAVR, UNI/O, and XMEGA are registered trademarks of Microchip Technology
Incorporated in the U.S.A. and other countries.
ClockWorks, The Embedded Control Solutions Company, EtherSynch, Hyper Speed Control, HyperLight
Load, IntelliMOS, mTouch, Precision Edge, and Quiet-Wire are registered trademarks of Microchip
Technology Incorporated in the U.S.A.
Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, BodyCom,
CodeGuard, CryptoAuthentication, CryptoAutomotive, CryptoCompanion, CryptoController, dsPICDEM,
dsPICDEM.net, Dynamic Average Matching, DAM, ECAN, EtherGREEN, In-Circuit Serial Programming,
ICSP, INICnet, Inter-Chip Connectivity, JitterBlocker, KleerNet, KleerNet logo, memBrain, Mindi, MiWi,
motorBench, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient
Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, PowerSmart, PureSilicon, QMatrix, REAL ICE,
Ripple Blocker, SAM-ICE, Serial Quad I/O, SMART-I.S., SQI, SuperSwitcher, SuperSwitcher II, Total
Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are
trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated in the U.S.A.
Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of
Microchip Technology Inc., in other countries.
All other trademarks mentioned herein are property of their respective companies.
PL360G55CF-EK
© 2019 Microchip Technology Inc. User Guide DS50002866A-page 5
© 2019, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved.
ISBN: 978-1-5224-4303-2
Quality Management System Certified by DNV
ISO/TS 16949
Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer
fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC®
DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design and manufacture of development
systems is ISO 9001:2000 certified.
PL360G55CF-EK
© 2019 Microchip Technology Inc. User Guide DS50002866A-page 6
AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Austin, TX
Tel: 512-257-3370
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Novi, MI
Tel: 248-848-4000
Houston, TX
Tel: 281-894-5983
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Tel: 317-536-2380
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Tel: 951-273-7800
Raleigh, NC
Tel: 919-844-7510
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
Tel: 408-436-4270
Canada - Toronto
Tel: 905-695-1980
Fax: 905-695-2078
Australia - Sydney
Tel: 61-2-9868-6733
China - Beijing
Tel: 86-10-8569-7000
China - Chengdu
Tel: 86-28-8665-5511
China - Chongqing
Tel: 86-23-8980-9588
China - Dongguan
Tel: 86-769-8702-9880
China - Guangzhou
Tel: 86-20-8755-8029
China - Hangzhou
Tel: 86-571-8792-8115
China - Hong Kong SAR
Tel: 852-2943-5100
China - Nanjing
Tel: 86-25-8473-2460
China - Qingdao
Tel: 86-532-8502-7355
China - Shanghai
Tel: 86-21-3326-8000
China - Shenyang
Tel: 86-24-2334-2829
China - Shenzhen
Tel: 86-755-8864-2200
China - Suzhou
Tel: 86-186-6233-1526
China - Wuhan
Tel: 86-27-5980-5300
China - Xian
Tel: 86-29-8833-7252
China - Xiamen
Tel: 86-592-2388138
China - Zhuhai
Tel: 86-756-3210040
India - Bangalore
Tel: 91-80-3090-4444
India - New Delhi
Tel: 91-11-4160-8631
India - Pune
Tel: 91-20-4121-0141
Japan - Osaka
Tel: 81-6-6152-7160
Japan - Tokyo
Tel: 81-3-6880- 3770
Korea - Daegu
Tel: 82-53-744-4301
Korea - Seoul
Tel: 82-2-554-7200
Malaysia - Kuala Lumpur
Tel: 60-3-7651-7906
Malaysia - Penang
Tel: 60-4-227-8870
Philippines - Manila
Tel: 63-2-634-9065
Singapore
Tel: 65-6334-8870
Taiwan - Hsin Chu
Tel: 886-3-577-8366
Taiwan - Kaohsiung
Tel: 886-7-213-7830
Taiwan - Taipei
Tel: 886-2-2508-8600
Thailand - Bangkok
Tel: 66-2-694-1351
Vietnam - Ho Chi Minh
Tel: 84-28-5448-2100
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
Finland - Espoo
Tel: 358-9-4520-820
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Germany - Garching
Tel: 49-8931-9700
Germany - Haan
Tel: 49-2129-3766400
Germany - Heilbronn
Tel: 49-7131-67-3636
Germany - Karlsruhe
Tel: 49-721-625370
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Germany - Rosenheim
Tel: 49-8031-354-560
Israel - Ra’anana
Tel: 972-9-744-7705
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Italy - Padova
Tel: 39-049-7625286
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Norway - Trondheim
Tel: 47-72884388
Poland - Warsaw
Tel: 48-22-3325737
Romania - Bucharest
Tel: 40-21-407-87-50
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Sweden - Gothenberg
Tel: 46-31-704-60-40
Sweden - Stockholm
Tel: 46-8-5090-4654
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
Worldwide Sales and Service
© 2019 Microchip Technology Inc. User Guide DS50002866A-page 7
Inhaltsverzeichnis
Andere Microchip Technology Hauptplatine Handbücher
Microchip Technology
Microchip Technology Explorer 16 Bedienungsanleitung
Microchip Technology
Microchip Technology EVB-KSZ9563 Bedienungsanleitung
Microchip Technology
Microchip Technology TC1303 DFN Bedienungsanleitung
Microchip Technology
Microchip Technology AVR-BLE Installationshandbuch
Microchip Technology
Microchip Technology EVB-USB4715 Bedienungsanleitung
Microchip Technology
Microchip Technology ATtiny3217 Xplained Pro Bedienungsanleitung
Microchip Technology
Microchip Technology EVB-LAN9252-3PORT Bedienungsanleitung
Microchip Technology
Microchip Technology OS81210 Bedienungsanleitung
Microchip Technology
Microchip Technology SOT89-3 Bedienungsanleitung
Microchip Technology
Microchip Technology Microsemi Silicon Sculptor 4 Technisches Handbuch
Microchip Technology
Microchip Technology PIC32CM LE00 Bedienungsanleitung
Microchip Technology
Microchip Technology IS2066B Bedienungsanleitung
Microchip Technology
Microchip Technology SOT23-5 Bedienungsanleitung
Microchip Technology
Microchip Technology EVB-USB3503 QFN Bedienungsanleitung
Microchip Technology
Microchip Technology MPLAB PM3 Gebrauchsanweisung
Microchip Technology
Microchip Technology AVR-IoT WA Bedienungsanleitung
Microchip Technology
Microchip Technology MCP73213 OVP Bedienungsanleitung
Microchip Technology
Microchip Technology PICkit 2 Bedienungsanleitung
Microchip Technology
Microchip Technology SAM E70 Xplained Ultra Bedienungsanleitung
Microchip Technology
Microchip Technology ATF15 Series Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Bedienungsanleitung
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
