Microscan HS-21 Bedienungsanleitung

Step 2 — Set Up Hardware (USB)

Note: The USB interface draws its power from the host.

Hardware for USB

USB Installation

To power on the reader, plug the

USB cable into the reader’s

handle and into the host’s USB

port. After several seconds, the

reader will beep twice and the

LED will turn off. The reader will

now be ready to use.

Important:

If you use a USB hub,

be sure that it is a powered hub.

1HS-21 Handheld Reader FIS-HS21-000XG

HS-41X Handheld Reader FIS-HS41X-000XG

2USB Cable, 6’ Straight 61-000224-01

USB Cable, 8’ Coiled 61-000224-02

USB Hardware

Default to USB

(HID)

Save

Settings

Test Symbol

(ABCDEFGHIJKLMNOP)

Step 1 — Check Required Hardware

The HS-21/HS-41X is shipped with one of the following cables:

USB Hardware

1. HS-21/HS-41X Handheld Reader

2. USB cable

RS-232 Hardware

1. HS-21/HS-41X Handheld Reader

2. RS-232 Cable

3. RS-232 Power Supply

Detaching the Cable

The reader can be converted from USB to RS-232 or from RS-232 to

USB by changing the cable and scanning the appropriate communications

programming symbol below. To detach the USB or RS-232 cable

from the reader, press a paper clip into the hole on the side of the

handle and gently pull the cable out of the connector.

6’ USB

Straight

Cable

8’ RS-232

Coiled

Cable

Save

Settings

USB

Interface

RS-232

Interface

Quick Start Guide

HS-21/HS-41X

Handheld Reader

P/N 83-110003 Rev A

Step 2 — Set Up Hardware (RS-232)

Hardware for RS-232

RS-232 Installation

To power on the reader, plug the

RS-232 cable into the reader’s

handle, plug the power supply into

the AC outlet, plug the power supply

cord into the barrel jack on the

cable, and then connect the cable

to the appropriate serial port on

the host. The unit will beep twice

and the LED will turn off. The

reader will now be ready to use.

1HS-21 Handheld Reader FIS-HS21-000XG

HS-41X Handheld Reader FIS-HS41X-000XG

2RS-232 Cable, 8’ Coiled 61-000224-03

RS-232 Power Supply, 8’ Coiled, U.S.

20-000335-02

RS-232 Power Supply, 8’ Coiled, Euro

20-000336-02

RS-232 Power Supply,

8’ Coiled, UK 20-000337-02

RS-232 Hardware

Reset to RS-232

Factory Defaults

Save

Settings

Test Symbol

(ABCDEFGHIJKLMNOP)

Step 3 — Install ESP

ESP Software is Microscan’s configuration and testing software. Use

ESP to set up your HS-21 and HS-41X Handheld Reader.

ESP can be found on the Microscan Tools Drive that is packaged with

the reader.

1. Follow the prompts to install ESP from the Tools Drive.

2. Click on the ESP icon to run the program.

Note: ESP can also be installed from the Download Center at

www.microscan.com.

Minimum System Requirements

•233 MHz Pentium PC

•Windows 8, 7, Vista, or XP operating system (32-bit or 64-bit)

•Internet Explorer 6.0 or higher

•128 MB RAM or greater

•160 MB free disk space

•800 x 600 256 color display (1024 x 768 32-bit color

recommended)

Step 4 — Select Model

When you start ESP, the following menu will appear:

1. Click the HS-21/HS-41X button and then click OK. If you

do not want to make this selection every time you start

ESP, uncheck “Show this dialog at startup”. If you need to

select another model later, click Switch Model at the top of

the screen.

Note: You can also type a name of your choice in the

Description text field and click OK.

2. Click Yes when this dialog appears:

Step 7 — Configure the Reader

Click the App Mode button to make configuration changes.

The following modes are accessible by clicking the buttons in

the first row of App Mode icons:

• Click the EZ Mode button to return to the EZ Mode view.

• Click the Autoconnect button to establish communication.

• Click the Send/Recv button to send or receive commands.

• Click the Switch Model button to open the model menu.

• Click the

Parameters

button to show the tabbed tree controls for

Communication, Read Cycle, Symbologies, and I/O Parameters.

• Click the Imager button to capture and decode symbols and

to use Window of Interest for Near Field and Far Field.

• Click the Terminal button to display decoded symbol data

and to send serial commands to the reader using text or macros.

• Click the Utilities button to show the tabbed interfaces for

Device Control, Differences from Default, Firmware, and

Advanced settings.

For further details, see ESP Help in the dropdown Help menu or

refer to the HS-21/HS-41X Handheld Reader User Manual.

Step 6 —

Connect to ESP

USB

Once you have clicked Connect in the USB Select Device

field, the CONNECTED message will appear in a green box in

the status bar at the bottom right of the screen.

You are now ready to configure the USB HS-21/HS-41X using

ESP

RS-232

Once you have selected RS-232 settings and communications

port and clicked

Connect

, the

CONNECTED

message will appear

in a green box in the status bar at the bottom right of the screen.

You are now ready to configure the RS-232 HS-21/HS-41X

using ESP.

Step 5 — Select Interface

USB

Print and

decode the

USB Connect Mode

symbol to ensure

that you are in the correct

communications mode. Keep the

printed symbol in a convenient

place for future use. Click

when you are finished.

2. You will then see your reader’s ID in the Select Device

field. The Reader ID number should match the serial number

next to the trigger under the optical head of the reader.

Click Connect.

RS-232

Print and decode the RS-232 Connect Mode symbol and

decode it

with the reader to ensure that you are in the correct

communications mode. Keep the printed symbol in a convenient

place for future use. Be sure the correct communications

port is selected. Click Next, and then Connect.

Click the Show

Connect Symbol

button.

Click the Show

Connect Symbol

button.

Step 8 — Save Changes in ESP

To make changes to a configuration setting:

•Send, No Save. Changes will be lost when power is re-applied

to the reader.

•Send and Save. This activates all changes in current memory

and saves to the reader for power-on.

1. Left-click on the

+to expand the

desired tree.

2. Double-click on

the desired

parameter and

click once in the

selection box to

view options.

5. Right-click on

the open

screen and

select Save to

Reader to

implement the

command in

the reader.

3. Place your cursor

in the selection

box, scroll down

to the setting you

want to change,

and click once on

the setting.

4. Left-click on the

open screen to

complete your

selection.

Andere Handbücher für HS-21

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Microscan Barcode-Lesegerät Handbücher

Microscan

Microscan MS-3 Bedienungsanleitung

Microscan

Microscan MS-820 Bedienungsanleitung

Microscan

Microscan QX-830 Bedienungsanleitung

Microscan

Microscan LVS-9510 Produkthandbuch

Microscan

Microscan MS-4Xi Bedienungsanleitung

Microscan

Microscan MS-820 Bedienungsanleitung

Microscan

Microscan HS-51 Bedienungsanleitung

Microscan

Microscan MS-1 Gebrauchs- und Pflegehandbuch

Microscan

Microscan MicroHAWK ID-30 Bedienungsanleitung

Microscan

Microscan Mobile Hawk Bedienungsanleitung

Microscan

Microscan MS-2 Bedienungsanleitung

Microscan

Microscan Quadrus MINI Imager Bedienungsanleitung

Microscan

Microscan MS-4 Bedienungsanleitung

Microscan

Microscan LVS-9510 Bedienungsanleitung

Microscan

Microscan HS-2D Bedienungsanleitung

Microscan

Microscan MS-Q Imager Bedienungsanleitung

Microscan

Microscan MS-Q Imager Bedienungsanleitung

Microscan

Microscan MINI Hawk Xi Bedienungsanleitung

Microscan

Microscan HawkEye 45T Bedienungsanleitung

Microscan

Microscan LVS-9580 Bedienungsanleitung

Microscan

Microscan MS-820 Bedienungsanleitung

Microscan

Microscan MINI Hawk Bedienungsanleitung

Microscan

Microscan HawkEye 1500 Series Bedienungsanleitung

Microscan

Microscan HS-2D Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung