Midea MWTF-24CM Bedienungsanleitung

Before using your air conditioner, please read

this manual carefully and keep it for future reference.

WINDOW/WALL TYPE

ROOM AIR CONDITIONER

Prior to installation this air-conditioning unit

must be submitted for approval by the utility

service which provides electricity.

CONTENTS

1. IMPORTANT SAFETY INSTRUCTIONS.................................................2

2. .............................................3

3. UNIT PARTS IDENTIFICATION ................. .............................................4

4. AIR CONDITIONER FEATURES..............................................................5

5. CARE AND CLEANING ...........................................................................7

6. INSTALLATION.........................................................................................8

7. TROUBLESHOOTING TIPS.................................................................11

8. SPECIFICATIONS ................................................................................12

POINTS FOR USING AIR CONDITIONER

NOTE: This User s Manual provides specific

operating instructions for your model. Use the

room air conditioner only as instructed in this

User s Manual. These instructions are not

meant to cover every possible condition and

situation that may occur. Common sense and

caution must be practiced when installing,

operating, and maintaining any appliance.

IMPORTANT SAFETY INSTRUCTIONS

All wiring must comply with local and national electrical codes and be installed

by a qualified electrician.

Never insert your fingers or any foreign objects into the air outlet.

Take special care to warn children of these dangers.

Be sure the air conditioner is properly grounded. To minimize shock and fire

hazards, proper grounding is important. The power cord is equipped with a three-

prong grounding plug for protection against shock hazards.

Your air conditioner must be used in a properly grounded wall receptacle. If the

wall receptacle you intend to use is not adequately grounded or protected by a

time delay fuse or circuit breaker, have a qualified electrician install the proper

receptacle. Ensure the receptacle is accessible after the unit installation.

Do not run air conditioner with outside protective cover in place. This could result

in mechanical damage within the air conditioner.

The capacity of the room air conditioner must fit the room size for efficient and

satisfactory operation.

Install the room air conditioner on the shady side of your room.

Do not block air flow inside with blinds, curtains or furniture; or outside with shrubs,

enclosures, or other buildings.

Keep blinds and drapes in other windows closed during the sunniest part of the

day.

Clean the air filter as recommended in the section Care and Cleaning .

Do not use an extension cord or an adapter plug.

WARNING For your safety

Do not store or use gasoline or other flammable vapors and liquids in the vicinity

of this or any other appliance.

Avoid fire hazard or electric shock. Do not use an extension cord or an adaptor

plug. Do not remove any prong from the power cord.

WARNING Electrical Information

Energy Saving Ideas

POINTS FOR USING AIR CONDITIONER

NOTE:

To begin operating the air conditioner, follow these steps:

If the air conditioner is turned off, wait 3 minutes before restarting. This

allows pressure inside the compressor and equalize. Failure to follow these

instructions may be harmful to your unit.

1. Set the thermostat to the highest number (coldest or cooler setting).

2. Set the selector control to the highest COOL setting.

3. Adjust the louver for comfortable air flow (see AUTO SWING).

4. Once the room has cooled, adjust the thermostat to the setting you find most

comfortable.

5. Make sure that the air flow inside and outside are not obstructed by anything.

WARNING To reduce the risk of fire, electric shock, or injury to persons,

read the IMPORTANT SAFETY INSTRUCTIONS before

operating this appliance.

If the unit is operated beyond the conditions specified above, it may cause a failure

of the unit.

6. This air conditioner is designed to be operated under conditions as follows:

Cooling Operation

Outdoor temp.: 18-43

C(T Environment)1

Indoor temp.: 18-32 C

O(T Environment)

Note: The relative humidity of home should be less

than 80%. If the unit is used in a condition with a

relative humidity over 80%, there will be condensed

water on the appearance of the unit.

21-52

C(T Environment)3

18-32

C(T Environment)3

1. Front panel

2. Air filter

3. Frame

4. Cabinet

5. Air inlet grille (outdoor side)

6. Air outlet grille

7. Operation knob

8. Power supply cord and plug

UNIT PARTS IDENTIFICATION

ACCESSORIES

Screw(Fasten the front panel)

Drain Plug(option)

Drain Pan (option)

Seal

1. Power cord conductors are distinguished according to color as follows (see Fig.1)

2. For your safety and protection, this unit is earthed through the power cord (see Fig.2)

Please contact the manufacturer or its service agent or a similar qualified person if

you want to replace it.

3. Be sure that the unit being correctly grounded. The wall outlet (Air-break switch)should be

provided with reliable earth wire.

4. The unit should be provided with an individual circuit and the circuit breaker/fuse

rating should be the same as that of the power cord and wall outlet.

POWER

CORD

E-Earth wire, yellow/green

N-Neutral wire, blue

A-Active wire, brown

Fig.1 Fig. 2

Wall outlet Air-break switch

NOTE: The outline of the operation panel is based on typical model, the function is the

same with your air conditioner while some difference may exist in appearance.

SELECTOR

POWER indicator(some models without): This indicator light remains on when the unit

is on and goes off when the SELECTOR is on OFF position.

AIR CONDITIONER FEATURES

THERMOSTAT

AUTO SWING SELECTOR

OFF

POWER

COOLER

HIGH

COOL

MED

COOL

LOW

COOL

HIGH

FAN

MED

FAN

LOW

FAN

WAIT THREE MINUTES

BEFORE RESTARTING

OFF

SELECTOR

OFF

HIGH

COOL

MED

COOL

LOW

COOL

HIGH

FAN

MED

FAN

LOW

FAN

The desired cool setting is selected by rotating the knob

to the right to the appropriate location.

has maximum cooling effect and airflow.

has minimum cooling effect and airflow.

has the intermediate cooling effect and

airflow.

will completely shut off the unit.

Rotate the knob to the left to select your choice of fan

speeds for air circulation.

When selecting a fan speed, the compressor will

not run.

The controls featured in this manual are representative

of many available models. Your model may offer slightly

different features.

Cool Mode

LOW

MED

OFF

Fan Mode

Note:

HIGH COOL

COOL

Note

When turning the SELECTOR knob from "LOW COOL" to "HIGH COOL", keep your speed slow as far

as possible. Do not change the operation mode between "LOW COOL" and "HIGH COOL" too often.

THERMOSTAT SELECTOR

OFF

COOLER

HIGH

COOL

LOW

COOL

HIGH

FAN

LOW

FAN

WAIT THREE MINUTES

BEFORE RESTARTING

OFF

HIGH

COOL

LOW

COOL

HIGH

FAN

LOW

FAN

OFF

HIGH

COOL

MED

COOL

LOW

COOL

HIGH

FAN

LOW

FAN

THERMOSTAT

COOLER

To set the desired room temperature, rotate the

thermostat switch to the desired setting. After

the set temperature is achieved the thermostat

will automatically start and stop the compressor

in order to maintain the desired set temperature.

Rotate the thermostat selector clockwise for

higher cool settings. Higher cool settings will

provide lower room temperature. Rotate the

thermostat selector counter clockwise for lower

cool settings. Lower cool settings will provide

higher room temperature.

Thermostat

The thermostat is used to set the desired room

temperature when the unit is being operated in

the COOL MODE.

NOTE:

COOLER

During the cooling operation of the unit, when the

thermostat knob is rotated clockwise, allow at least three

minutes before turning back the knob to the

direction. Otherwise the fuse may blow due to an overload

of the unit.

AUTO SWING

OFF ON

AUTO SWING

Horizontal air flow adjustment (automatically)

When the AUTO SWING switch is turned to ON

position, the vertical louvers automatically oscillate

right and left sweeping the cold air alternately to

obtain comfortable cooling. The vertical louvers may

be stopped at any position when the AUTO SWING

switch is turned OFF .

Vertical air flow adjustment (manually)

To adjust vertical air flow direction, adjust any one of

the horizontal louver blades. When turning up or down

the horizontal louver blades, always keep horizontality

the top or bottom blades. This can effectively prevent

water drops condensed on the front panel of the unit.

Vent Control

The vent control is located above the control knobs. The operation method is different

on different models (see the following figures).

For maximum cooling efficiency, CLOSE the vent. This will allow internal air circulation.

OPEN the vent to discharge stale air.

CLOSE VENT OPEN

To open the vent, pull the lever toward you

To close it, push it in.

To open the vent, set the lever to the right position

To close it, set the lever in the left position.

CLOSE OPEN

NOTE: The VENTILATION LEVER should normally be kept in the CLOSED position during

cooling for maximum cooling effect. The "OPEN" position is used only for ventilation.

CARE AND CLEANING

Clean your air conditioner occasionally to keep it looking new. Be sure to unplug

the unit before cleaning to prevent chock or fire hazards.

CAUTION

Air Filter Cleaning

The air filter should be checked at least once a

month to see if cleaning is necessary. Trapped

particles in the filter can build up and cause an

accumulation of frost on the cooling coils.

Hold the slot under the front panel, then uplift it onwards, and remove the front panel.

Pinch the handle under the air filter and make the air filter arched, remove it from the

underside to upside.

Wash the filter using liquid dishwashing detergent and warm water. Rinse filter thoroughly.

Gently shake excess water from the filter. Be sure the filter is thoroughly dry before

replacing.

Or, instead of washing you may vacuum the filter clean.

Never use hot waterNote:

over 40 C(104 F) to clean the air filter. Never attempt to

operate the unit without the air filter.

CARE AND CLEANING(CONTINUED)

Never use water over 50 C, alcohol, gasoline, acid, solvent or brush to

clean the front panel as this will damage the surface of the part.

NOTE:

If you plan to store the air conditioner during the winter, remove it carefully from the

window according to the installation instructions. Cover it with plastic or return it to

the original carton.

Winter Storage

Never use harsh cleaners, wax or polish on the cabinet front.

Be sure to wring excess water from the cloth before wiping around the controls.

Excess water in or around the controls may cause damage to the air conditioner.

Plug in air conditioner.

Cabinet Cleaning

Be sure to unplug the air conditioner to prevent shock or fire hazard. The cabinet

and front may be dusted with an oil-free cloth or washed with a cloth dampened in

a solution of warm water and mild liquid dishwashing detergent. Rinse thoroughly

and wipe dry.

&Select The Best Location

Install the unit at a place having sufficient strength to support the unit securely.

For maximum efficiency, install the air conditioner on a side of a house or building

which favors more shade than direct sunlight.

Provide sufficient clearance or space around the air inlet and air outlet so that air

flow will not be obstructed, following figures give detailed requirements.

Only trained and qualified service personnel should install, repair or service air

conditioning equipment. Users should not install the air conditioner by themselves.

INSTALLATION

Scrape

5-10mm

Less than C

more than D

More thanA

More than B

Less than

more thanA

Wall thickness is less than C

If the wall thickness is more than

scrape the wall as shown above.

Make rear side lower so that water will drain

out smoothly.

Size(mm)

400

500

210

INSTALLATION(CONTINUED)

The Treatment of Condensed Water

To meet different requirement of different type of air

conditioner, there are two kinds of methods for your

choice to treat the condensed water. You can choose

back drainage or non-drainage. See the following

procedures to perform back drainage:

1. Fit the seal onto the drain joint (which provided with

your air conditioner accessory).

2. Remove the rubber plug from the back of the unit.

3. Attach the drain joint to the back of the cabinet

where you remove the plug and rotate 90 to securely

assemble them.

4. Connect the drain joint with a extension drain hose

(Locally purchased)

OSEAL

DRAIN

JOINT RUBBER

PLUG

Inhaltsverzeichnis

Andere Midea Klimaanlage Handbücher

Midea

Midea V6R VRF Series Bedienungsanleitung

Midea

Midea MUE-18FNXD0 Bedienungsanleitung

Midea

Midea Inverter Split-type Room Air Conditioner Bedienungsanleitung

Midea

Midea F Series Bedienungsanleitung

Midea

Midea MWHUK-05CMN8-BCK0 Bedienungsanleitung

Midea

Midea 373127 Reparaturanleitung

Midea

Midea FLOOR TYPE Bedienungsanleitung

Midea

Midea MCD-18HRFN1-QRD0 Bedienungsanleitung

Midea

Midea MTIU-07HWFNX-QRD0W Bedienungsanleitung

Midea

Midea Everstar MPM-05CE-BB7 Bedienungsanleitung

Midea

Midea Blanc Pro Series Bedienungsanleitung

Midea

Midea PREMIER SERIES Bedienungsanleitung

Midea

Midea MCD-18HRFN1-QRC4 Bedienungsanleitung

Midea

Midea MSV1-07CR-QB8F Bedienungsanleitung

Midea

Midea MDV-D18Q1/N1-D Bedienungsanleitung

Midea

Midea AC100-U Bedienungsanleitung

Midea

Midea GAIA Series Bedienungsanleitung

Midea

Midea MFGA-60ARDN1-QC2 Bedienungsanleitung

Midea

Midea FG Europe MSMTAU-09 Bedienungsanleitung

Midea

Midea MSV1I-09HRDN1 Betriebsanleitung

Midea

Midea MSH-18HRIN1 Bedienungsanleitung

Midea

Midea M thermal Mono Series Bedienungsanleitung

Midea

Midea MFS2-24ARN1 Bedienungsanleitung

Midea

Midea MAC-450CR Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Spheros

Spheros CC 355 Bedienungsanleitung

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Bedienungsanleitung

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Samsung

Samsung AR KV Series Leitfaden

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

Hitachi

Hitachi RAS-E24CAK Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Hisense

Hisense 7K Technisches Handbuch

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung