Miele KM 6565 FR Bedienungsanleitung

11004250-02

Installation

*INSTALLATION*

Safety instructions for installation

Damage risk from incorrect installation.

Incorrect installation can cause damage to the hob.

The hob must only be installed by a qualified person.

Risk of electric shock.

Incorrect connection to the mains supply may result in an electric shock.

The hob must be connected to the electrical supply by a qualified person only.

Damage from falling objects.

Take care not to damage the hob when fitting wall units or a cooker hood above

it.

Fit the wall units and the cooker hood before the hob.

 The veneer or laminate coatings of worktops (or adjacent kitchen

units) must be treated with 100°C heat-resistant adhesive which will

not dissolve or distort. Any backmoulds must be of heat-resistant

material.

 The hob must not be installed over a fridge, fridge-freezer, freezer,

dishwasher, washing machine, washer-dryer or tumble dryer.

 After installation, ensure that nothing can come into contact with

the connection cable and that it is without hindrance.

 The electrical cable may not come into contact with any moving

kitchen component (e.g. a drawer) or be subject to mechanical

obstruction which could damage it.

 Observe carefully the safety clearances listed on the following

pages.

11004250-02

Installation

*INSTALLATION*

Safety distances

Safety distance above the hob

The safety distance specified by the

manufacturer of the cooker hood must

be maintained between the hob and the

cooker hood above it.

If combustible objects are installed

above the hob (e.g., cabinets, utensil

rail, etc.), a minimum safety distance of

600mm must be maintained.

When two or more appliances which

have different safety distances are

installed together below a cooker

hood, you should observe the

greatest specified safety distance.

11004250-02

Installation

*INSTALLATION*

Safety distances to the sides and

back of the appliance

It is advisable to install the hob with

plenty of space either side of it.

The minimum distance  shown below

must be maintained between the back

of the hob and a tall unit or wall.

The minimum distance ,  shown

below must be maintained between a

tall unit or a wall to the left or right of

the hob with a minimum distance of

300mm on the opposite side.

Minimum distance between the back

of the worktop cut-out and the rear

edge of the worktop:

50mm

Minimum distance between the

worktop cut-out and a wall or tall unit to

the right of it:

50mm.

Minimum distance between the

worktop cut-out and a wall or tall unit to

the left of it:

50mm.

Not allowed

Highly recommended

Not recommended

11004250-02

Installation

*INSTALLATION*

Interim shelf

It is not necessary to fit an interim shelf

underneath the hob but one may be

fitted if you wish.

If an interim shelf is fitted under the

hob, there must be a minimum gap of

110 mm between the top of the

worktop and the top of the shelf.

A gap of 10mm should be left at the

back of the shelf to accommodate the

cable. For hobs with an external mains

connection box, this gap must be at

least 30mm.

11004250-02

Installation

*INSTALLATION*

Safety distance when installing the appliance near a wall with additional

niche cladding

A minimum safety distance must be maintained between the worktop cut-out and

any niche cladding to protect it from heat damage.

If the niche cladding is made from a combustible material (e.g. wood) a minimum

safety distance  of 50 mm must be maintained between the cut-out and the

cladding.

If the niche cladding is made from a non-combustible material (e.g. metal, natural

stone, ceramic tiles) the minimum safety distance  between the cut-out and the

cladding will be 50 mm less the thickness of the cladding.

Example: 15 mm niche cladding

50mm - 15mm = minimum safety distance of 35mm

Flush-fitted hobs Hob with frame or bevelled edge

aMasonry

bNiche cladding dimension x = thickness of the niche cladding material

cWorktop

dWorktop cut-out

eMinimum distance to

combustible materials 50mm

non-combustible materials 50mm - dimension x

11004250-02

Installation

*INSTALLATION*

Installation notes

Seal between the hob and the

worktop

Damage caused by incorrect

installation.

Using sealant under the hob could

result in damage to the hob and the

worktop if the hob ever needs to be

removed for servicing.

Do not use sealant between the hob

and the worktop.

The sealing strip under the edge of

the hob provides a sufficient seal for

the worktop.

Sealing strip

Dismantling the hob for service

purposes may damage the sealing

strip underneath the edge of the hob.

Always replace the sealing strip

before reinstalling the hob.

Tiled worktops

Grout lines and the hatched area

underneath the hob frame must be

smooth and even. If they are not the

hob will not sit flush with the worktop

and the sealing strip underneath the

hob will not provide a good seal

between the hob and the worktop.

11004250-02

Installation

*INSTALLATION*

Building-in dimensions

All dimensions are given in mm.

KM6565FR

aFront

bMains connection box with mains connection cable

Mains connection cable L=1.440mm

cWiFi stick connection

dSpring clamps

11004250-02

Installation

*INSTALLATION*

Installation

Preparing the worktop

Create the worktop cut-out.

Remember to maintain the minimum

safety distances (see “Installation –

Safety distances”).

Wooden worktops

Seal any cut surfaces on wooden

worktops with a special varnish,

silicone sealant or resin to prevent the

wood from swelling as a result of

moisture ingress. The sealant must

be heat-resistant.

Make sure that the sealant does not

come into contact with the top of the

worktop.

The seal under the appliance ensures

that the hob will sit securely in the cut-

out without slipping. Any gap between

the appliance frame and worktop will

become smaller over time.

Secure the spring clamps

The exact positioning of the spring

clamps is shown in the individual hob

diagrams.

Wooden worktops

Position the spring clamps on the

top edge of the cut-out as shown in

the hob illustration.

Fasten the spring clamps using the

3.5x25mm wood screws supplied

with the appliance.

11004250-02

Installation

*INSTALLATION*

Natural stone worktops

You will need heavy duty double-sided

adhesive tape (not included with the

hob) to fasten the spring clamps.

Attach the adhesive tape along the

top edge of the cut-out in the

positions shown in the hob

illustration.

Position the spring clamps on the top

edge of the cut-out and press them

firmly into place.

Coat the side edges and the lower

edges of the spring clamps with

silicone.

Install the hob

Feed the mains connection cable for

the hob down through the worktop

cut-out.

Position the hob in the worktop cut-

out.

Using both hands, press down evenly

on the sides of the hob until it clicks

into position. When doing this make

sure that the seal of the appliance sits

flush with the worktop on all sides.

This is important to ensure an

effective seal all round.

If the seal does not meet the worktop

correctly on the corners, the corner

radius (≤R4) can be carefully scribed

to suit.

Do not use any additional sealant

(e.g. silicone) on the hob.

Connect the hob to the mains.

Check that the hob works.

The hob can only be removed using a

special tool.

11004250-02

Installation

*INSTALLATION*

Electrical connection

Risk of damage from incorrect

connection.

Unauthorised installation,

maintenance and repairs can cause

considerable danger for the user.

Miele cannot be held liable for

damage or injury caused by

unauthorised installation,

maintenance or repair work, or by an

inadequate or faulty on-site earthing

system (e.g. electric shock).

This hob must be connected to the

electrical supply by a qualified

electrician.

The electrician must be familiar with

and comply with the national

regulations and any additional

regulations of the local electricity

provider.

After installation, ensure that all

electrical components are shielded

and cannot be accessed by users.

Total power rating

See data plate

Connection data

The connection data is quoted on the

data plate. Please ensure these match

the household mains supply.

Please see wiring diagrams for

connection.

Disconnecting devices

It must be possible to disconnect the

hob from the mains at all poles using

disconnecting devices. A contact

distance of at least 3mm must be

observed in the switched-off state. The

disconnecting devices are overcurrent

protection devices and residual current

protection devices.

Disconnecting from the mains

Risk of electric shock.

There is a risk of electric shock if the

appliance is connected to the mains

supply during repair or service work.

After disconnection, ensure the

appliance cannot be switched back

on by mistake.

To disconnect the appliance from the

mains power supply, do one of the

following depending on installation:

Safety fuses

Completely remove fuses.

Automatic circuit breakers

Press the (red) test button until the

middle (black) button springs out.

Andere Handbücher für KM 6565 FR

Inhaltsverzeichnis

Andere Miele Kochfeld Handbücher

Miele

Miele KM 7564 FR Bedienungsanleitung

Miele

Miele KM 2051 Technisches Datenblatt

Miele

Miele KM 5773 Bedienungsanleitung

Miele

Miele KM 7678 FR Bedienungsanleitung

Miele

Miele hdsn-30 CS 7641 FL Bedienungsanleitung

Miele

Miele KM 7629 FX Bedienungsanleitung

Miele

Miele CS 1221 Bedienungsanleitung

Miele

Miele KM 3054 Bedienungsanleitung

Miele

Miele ProLine CS 1013-1 Bedienungsanleitung

Miele

Miele KM 2014 Bedienungsanleitung

Miele

Miele KM 3054-1 Bedienungsanleitung

Miele

Miele KM 417 Bedienungsanleitung

Miele

Miele KM 6629 Montageanleitung

Miele

Miele KM 247 Bedienungsanleitung

Miele

Miele KM 7564 FR Bedienungsanleitung

Miele

Miele KM 2356-1 Bedienungsanleitung

Miele

Miele KM 6112 Bedienungsanleitung

Miele

Miele SmartLine CS 7612 Bedienungsanleitung

Miele

Miele KMR 1124LP Bedienungsanleitung

Miele

Miele CS 1021 Bedienungsanleitung

Miele

Miele KM 7678 FR Bedienungsanleitung

Miele

Miele KM 5722 Montageanleitung

Miele

Miele SmartLine Tepan Yaki Bedienungsanleitung

Miele

Miele KM 7678 FR Bedienungsanleitung

Beliebte Kochfeld Handbücher anderer Marken

Siemens

Siemens EX875KYV1E Technisches Datenblatt

AEG

AEG CERAMIC HOB 6010 K Bedienungsanleitung

VALERA

VALERA CT 70A Bedienungsanleitung

Zanussi

Zanussi ZGF 6420 Bedienungsanleitung

Gaggenau

Gaggenau CI 273 Bedienungsanleitung

G3 Ferrari

G3 Ferrari Energy Bedienungsanleitung

Pkm

Pkm IN4B Bedienungsanleitung

Award

Award H903BG Bedienungsanleitung

Zanussi

Zanussi VCH 5005 RZ Bedienungsanleitung

Hotpoint

Hotpoint IS67V8CCXT/E Bedienungsanleitung

AEG

AEG HK854870XB Bedienungsanleitung

Cookology

Cookology SEP600BK Bedienungsanleitung

Bauknecht

Bauknecht Hob Bedienungsanleitung

Zanussi

Zanussi ZGM 782 Bedienungsanleitung

dipo INDUCTION

dipo INDUCTION DIBK218S Bedienungsanleitung

Blomberg

Blomberg MKN 24201 W Bedienungsanleitung

Progress

Progress PAI3101F Bedienungsanleitung

Hotpoint Ariston

Hotpoint Ariston PKL 641 IX/HA Bedienungsanleitung