Miele F 1813 SF Bedienungsanleitung
Installation Instructions
F 1813 SF, F 1913 SF en - CA
Installation, repair and maintenance work should be performed by
a Miele authorized service technician in accordance with national
and local safety regulations and the provided installation instructions.
Disposing of the packaging
materials
The packaging is designed to protect
the appliance from damage during
transportation. The packaging materials
used are selected from materials which
are environmentally friendly for disposal
and should be recycled.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of children. Return
the packaging to your dealer.
Disposal of your old appliance
Old appliances may contain materials
that can be recycled. Please contract
your local recycling authority about the
possibility of recycling these materials.
Instead, please contact your
municipality's waste collection center to
return and recycle electric and
electronic appliances.
Please take care not to damage the
pipework while the appliance is being
stored for transport to a waste disposal
facility.
By protecting the pipework, you help
keep the coolants and compressor oil
from contaminating the environment.
Before discarding an old appliance
disconnect it from the electrical supply
and cut off the power cord to prevent it
from becoming a hazard.
Caring for the environment
46
Have the appliance installed by a
qualified technician, according to
the enclosed installation
instructions.
WARNING
This appliance is top-heavy and
must be secured to prevent it from
tipping forward.
Keep the door closed until the
appliance is completely installed
and secured as per the installation
instructions.
Empty weight of your machine:
F 18X3 SF .........478lbs(217 kg)
F 19X3 SF .........552lbs(237 kg)
Climate Range
The appliance is designed for use
within certain climate ranges (ambient
temperatures) and should not be used
outside this range. The climate range of
this appliance is stated on the data
plate inside the appliance.
Climate
range
Ambient room temperature
SN
N
ST
T
+50°F (10 °C) to +90°F (32 °C)
+60°F (16 °C) to +90°F (32 °C)
+60°F (16 °C) to +100°F (38 °C)
+60°F (16 °C) to 110°F (43 °C)
Operating in a room which is too cold
will cause the compressor to switch off
for too long, causing the internal
temperature in the appliance to rise
with the risk of food deteriorating and
going off.
Installation site
The appliance should be installed in a
dry, well-ventilated room.
Do not install the appliance:
- outdoors
- in an environment with dripping
water
- in rooms that are at risk of frost.
The installation location should not be
exposed to direct sunlight, nor near a
heat source, such as an oven,
radiator, etc.
The ambient temperature should not
drop below 55°F (13°C) or rise above
110°F (43°C), otherwise malfunctions
may occur.
If installation next to a heat source is
unavoidable observe the following
minimum distances from the heat
source:
–1
1/4" (3 cm) from an electric cooktop
or electric oven.
– 12" (30 cm) from a gas or oil
cooktop, range or oven.
The following should also be taken into
consideration:
– The electrical outlet must be easily
accessible in case of an
emergency,not concealed behind
the appliance.
– The plug and cord must not touch
the rear of the appliance as they
could be damaged by vibrations
from the appliance.
– Do not plug in other devices behind
this appliance.
Installation
47
Important! When there is high
humidity a build-up of condensation
on the outer surfaces of the
appliance can occur.This can cause
the surfaces to corrode.To prevent
this, it is advisable to install the
appliance in a dry and/or an
air-conditioned room with sufficient
ventilation.Please ensure that doors
close and seal properly after
installation and that the appliance is
installed in accordance with these
installation instructions and and with
the required ventilation openings.
– If the room is too cold, it will cause
the cooling system in the appliance
to remain off for too long.This can
cause the temperature in the
appliance to rise, resulting in
damage.
Installation
48
Base
A fully loaded appliance is very heavy.
The load-bearing capacity of your floor
must meet the following requirements.
The approx. weight of a fully loaded
machine is:
F 18X3 SF ........1,007 lbs (457 kg)
F 19X3 SF ........1,197 lbs (543 kg)
To ensure that the appliance is installed
securely and functions properly, the
base must be flat, level and made of a
hard, rigid material.
If in doubt, contact Miele.
Furniture/fixtures
The new appliance will be mounted
securely to adjacent and overhead
furniture/fixtures.
For this reason, it is essential that all
attachable furniture/fixtures be
connected securely to the floor or wall
by a suitable means.
Ventilation
The air intake and outlet must not be
blocked or covered in any way. They
also need to be dusted/cleaned on a
regular basis.
Installation niche
To ensure safe, trouble-free installation
and the best possible cosmetic result,
check to be sure that the installation
space complies with the installation
dimensions. See "Niche dimensions".
The side walls of the installation cavity
must be plumb.
The minimum thickness of the side
walls and the top wall must be 5/8"
(16 mm).
The minimum thickness of the toe-kick
panel must be ½" (13 mm). A thickness
of 3/4" (19 mm) is recommended.
Installation
49
Stainless steel panels
Stainless steel door panels and toe-kick
covers are available from Miele.
Installation options
There are many different installation
options. You are limited only by the
design of the kitchen.
The door hinge cannot be
exchanged.
Single column
The appliance can be installed at any
preferred location in the kitchen.
However, be sure the door will open
and close properly in the chosen
location.
Side-by-side
This appliance can be installed
"side-by-side" with another
fridge/freezer using a "Merging Kit".
The "Merging Kit" is available from
Miele.
Contact Miele or your dealer for
specific information about which
combinations will work with your
appliance.
For instructions on how to attach the
appliances and install the heating
mat, please refer to the instructions
included with the "Merging Kit",
available from Miele.
Installation without a partition using
the "Merging Kit"
If the appliances are installed directly
next to each other (without a partition),
they need to be attached together
using the "Merging Kit".
Installation
50
Installation with partition using the
"Merging Kit"
The minimum thickness of the partition
is 5/8" (16 mm).
If there is a partition with a thickness
from 5/8" (16 mm) to 6 5/16" (160 mm)
between the adjacent appliances, then
each appliance should be individually
installed within its own niche using the
mounting accessories included.
The "Merging Kit" will also be needed.
The "Merging Kit" is available from
Miele.
Installation with partition without
using the "Merging Kit"
If there is a partition with a thickness of
more than 6 5/16" (160 mm) between
the adjacent appliances, then each
appliance should be individually
installed within its own niche using the
mounting accessories included (the
"Merging Kit" is not necessary).
Side panels
If one side of the appliance is visible, a
side panel must be used.
The side panel must be firmly secured
to the wall, the floor and the overhead
furniture/fixtures before the appliance is
placed in the cavity.
The dimensions of the side panel are
taken from the opposite wall of the
installation space. During installation,
ensure that the cavity is square and the
measurements are correct.
Installation
51
Door dimensions (open 115°)
AB
F 18X3 SF 32 5/8" (829 mm) 14 5/16" (363 mm)
F 19X3 SF 38 11/16" (982 mm) 16 7/8" (428 mm)
Miele recommends using the full door opening angle of 115° for this freezer.
Dimensions
52
Niche dimensions
Niche width (A)
F 18X3 SF 30" (762 mm)
F 19X3 SF 36" (915 mm)
Dimensions
53
Power supply and water connection
1. Power supply
2. Water connection
A
F 18X3 SF 15" (381 mm)
F 19X3 SF 18" (458 mm)
Install a pressure limiting device and water hammer arrester for inlet water
pressures exceeding 80 psi.(Refer to Uniform Plumbing Code, Sections 608.2
and 609.10) Never install or operate where inlet water pressure may exceed
120 psi.
,Power bars or extension cords are not safe (risk of fire). Do not use them to
connect the appliance to the power supply.
Dimensions
54
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Miele Kühlschrank Handbücher
Miele
Miele KT 4353 SD ed Technisches Datenblatt
Miele
Miele K 8852 SD Bedienungsanleitung
Miele
Miele K 8867 S-1 Bedienungsanleitung
Miele
Miele KFNS37452iDE Bedienungsanleitung
Miele
Miele KWT 6312 UGS Bedienungsanleitung
Miele
Miele KFN 12823 SD-1 Bedienungsanleitung
Miele
Miele KFNS 37682 iD Bedienungsanleitung
Miele
Miele KD 3528 Sed Technisches Datenblatt
Miele
Miele F 1801 SF Bedienungsanleitung
Miele
Miele KF 2981 Vi Bedienungsanleitung
Miele
Miele KD 683 i-3 Technisches Datenblatt
Miele
Miele K 1801 Vi Bedienungsanleitung
Miele
Miele KFN 37432 iD Bedienungsanleitung
Miele
Miele K 14827 SD Bedienungsanleitung
Miele
Miele K 34472 iD Bedienungsanleitung
Miele
Miele K 14827 SD Bedienungsanleitung
Miele
Miele K 1801 SF Bedienungsanleitung
Miele
Miele KFNS 37432 iD Bedienungsanleitung
Miele
Miele KD 1450 SD Technisches Datenblatt
Miele
Miele K 12820 SD ed Technisches Datenblatt
Beliebte Kühlschrank Handbücher anderer Marken
Bonnet Neve
Bonnet Neve SKYVIEW PLUS Bedienungsanleitung
Zanussi Electrolux
Zanussi Electrolux ZERB 8441 Bedienungsanleitung
Sharp
Sharp SJ-BA31IEXW2-EU Bedienungsanleitung
CORBERO
CORBERO CC2300MCW Bedienungsanleitung
KitchenAid
KitchenAid 2205264 Bedienungsanleitung
Stengel
Stengel KU 1101 A++ Bedienungsanleitung
