Miele KFN12823 SD Bedienungsanleitung

Installation Instructions

KFN12823 SD en - CA

Installation, repair and maintenance work should be performed by

a Miele authorized service technician in accordance with national

and local safety regulations and the provided installation instructions.

,Failure to follow these

instructions can result in death, fire,

or electrical shock.

Improper connection of the

equipment grounding conductor

may result in electric shock.

If you are in any doubt as to whether

the appliance has been properly

grounded, have the appliance

checked by a qualified electrician or

service technician.

Installation, repairs and other work

by unqualified persons could be

dangerous. The manufacturer will

not be held responsible for damage

or injury arising from unauthorized

work.

Before installing the appliance,

verify that the voltage, load and

circuit rating information found on

the data plate match the household

electrical supply.

,Do not ground to a gas pipe.

Check with a qualified elictrician if

you are not sure the appliance is

properly grounded. Do not have a

fuse in the neutral or grounding

curcuit.

,Electrocution hazard

Electrical grounding required. This

appliance is equipped with a

three-prong (grounding) polarized

plug for your protection against

possible shock hazards.

Do not remove the round grounding

prong from the plug.

Do not use a two-prong grounding

adapter.

Do not use extension cords or

ungrounded (two prong) adapters.

Connect this appliance to a 110 –

120 VAC, 60 Hz and 15 amp (20 amp

for side-by-side) circuit (20 amp for

side-by-side) with a circuit breaker or

fuse.

This appliance should have its own

separate grounded circuit.

The power cord is equipped with a

three-prong (grounding) plug for your

protection against potential electrical

shock. To maintain this protection:

– Do not modify the plug by removing

the round grounding prong.

– Do not use a two-prong adapter.

Where a two-prong wall outlet is

encountered, contact a qualified

electrician and have it replaced with

a three-prong outlet in accordance

with the local electrical codes and

regulations.

– Do not use a power cord that is

frayed or damaged.

– Do not connect the appliance using

an extension cord or extension

socket.

Electrical connection

The appliance must be connected to an

electrical outlet that is properly

grounded. The electrical installation

must comply with the applicable

electrical code.

The outlet must be easily accessible

and not concealed behind the

appliance so that the appliance can

quickly be disconnected from the

electricity supply in an emergency.

The plug and power cable must not

come into contact with the back of the

appliance, as they could be damaged

by vibrations from the appliance. This

may result in a short circuit.

In addition, no other appliances should

be plugged into a socket located

directly behind this appliance.

Do not use an extension cord to

connect the appliance to the power

supply. Extension cords do not

guarantee the required safety of the

appliance (e.g. they pose a danger of

overheating).

Do not connect the appliance to

stand-alone inverters, such as those

used with an autonomous energy

source, e.g. solar power systems.

Otherwise, when the appliance is

switched on, peak loads in the system

can cause the safety shutdown

mechanism to be triggered. This can

damage electronic units.

In addition, the appliance must not be

used with energy-saving devices,

which reduce the amount of energy

supplied to the appliance and cause it

to overheat.

If the power cable needs to be

replaced, this work must only be

performed by a qualified electrician.

Electrical connection

Safe operation of the appliance is

only assured if it has been installed

and connected in accordance with

these operating and installation

instructions.

WARNING!

Danger of tilting! To avoid a hazard

due to instability of the appliance, it

must be fixde in accordance with

the instructions.

Do not use any appliances which

give off heat, such as toaster ovens,

portable burners or toasters, on the

the appliance. The appliance may

catch fire. Fire hazard!

This fridge/freezer combination

should not be installed directly next

to a second model (in a side-by-side

position).

Because the appliance does not

have heated side walls, a

side-by-side installation can result in

the accumulation of condensation.

Contact your dealer for more

information.

Location

This appliance should not be installed

near windows where it is exposed to

direct sunlight or directly adjacent to

heat-producing appliances such as an

oven or a radiator. The higher the room

temperature, the longer the compressor

runs, increasing energy consumption

by the appliance. Install the appliance

in a dry, well-ventilated room.

The following should also be taken into

consideration:

– The power outlet must not be located

directly behind the appliance and

must be easily accessible in an

emergency.

– The plug and power cable must not

touch the back of the appliance, as

they could be damaged by vibrations

from the appliance.

– No other appliances should be

plugged into a socket located

directly behind this appliance.

Important! In environments with

high humidity condensation can

build up on the appliance exterior

and ultimately cause corrosion on the

outer walls.

To prevent this from happening, we

recommend installing the appliance

in a dry and/or an air-conditioned

room with sufficient ventilation.

Once you have completed the

installation, please make sure that the

appliance doors close properly, that

the ventilation openings are not

covered and that the appliance has

been installed as described in this

chapter.

Installation information

Climate class

The appliance is designed for use

within a certain climate class (room

temperature range) and should not be

used outside this range. The climate

class for your appliance is stated on the

data plate inside the appliance.

Climate class Room temperature

+10 °C à +32 °C

(50 °F à 90 °F)

+16 °C à +32 °C

(61 °F à 90 °F)

+16 °C à +38 °C

(61 °F à 100 °F)

+16 °C à +43 °C

(61 °F à 109 °F)

Operating in a room which is too cold

will cause the compressor to switch off

for too long. This may result in

increased temperatures inside the

appliance, which can even cause

frozen food to being thawing.

Ventilation

WARNING! Danger of damage from

overheating. May restrict operation.

Keep ventilation openings, in the

appliance enclosure or in the built-in

structure, clear of obstruction.

Air at the back of the appliance gets

warm. To ensure proper ventilation,

make sure that the ventilation openings

are not covered or blocked in any way.

They should also be dusted on a

regular basis.

Appliances with supplied wall

spacers

To achieve the indicated level of

energy consumption, you should

use the wall spacers that are

included with a number of

appliances. When installed, wall

spacers increase the appliance

depth by approx. 35 mm.

If you elect not to use the wall

spacers, your decision will have no

impact on the functioning of the

appliance. However, the smaller

distance to the wall means that there

will be a slight increase in this

appliance's energy consumption.

^Install the wall spacers in the top left-

and right-hand corners on the back

of the appliance.

Installation information

Installing the appliance

^First, remove the cable clip from the

back of the appliance.

^Check that all parts at the back of the

appliance can vibrate freely.

Carefully bend apart any parts that

are touching.

^Carefully slide the appliance into the

desired location.

^Position the appliance so that the wall

spacers (if installed) or the back of

the appliance are against the wall.

Aligning the appliance

^Use the adjustable feet to align the

appliance so that it is stable and

level.

Supporting the appliance door

^Make sure that you continue to

unscrew the adjustable foot afrom

the hinge plate until it rests on the

floor. Then turn the foot another 90° in

the same direction.

Installation information

Appliance dimensions

ABC

KFN 12823 SD edt/cs-2 1817 mm 600 mm 630 mm*

* Dimension without spacers. When the supplied spacers are installed, the depth

of the appliance increases by 35 mm.

Installation information

The appliance is delivered with

right-hand door hinging. If left-hand

hinging is required, the door hinging

must be reversed:

To reverse the door hinging, you will

need the following tools:

When reversing the door hinging,

always enlist the help of another

person.

Removing the door handles:

^When you pull the door handle a,

the sidebar bslides back.

^Remove the sidebar bfrom the

guide by firmly pulling towards the

appliance.

^Now loosen the four screws (TX15) in

the mounting plate and remove the

handle.

^Remove the cover caps from the

opposite side, and fit them into the

empty holes.

Reversing the door hinging

Removing the appliance doors:

Remove all food and drink from the

door shelves on the inside of the

doors.

^Close the upper door.

^Remove cover aby sliding it

forwards and lifting it off.

^Remove cover bby pulling it

upwards.

Caution! The upper door is no

longer secured in place once the

hinge plate has been removed in the

next step.

^Loosen the screws don the upper

hinge plate cand lift the hinge plate

upwards to remove.

^Carefully lift the upper door off of the

appliance and set it aside.

^Using a screwdriver, carefully loosen

the cover efrom above and remove

it together with the retaining plate f.

^Separate the retaining plate ffrom

the cover eby sliding it slightly to

the left and pulling the cover

forwards.

^Turn the retaining plate f180°.

^Fit cover eonto the front of the

retaining plate fand slide the cover

to the right. The writing must be

visible.

^Remove cover g, turn it 180° and

snap it into place on the opposite

side.

^Snap cover eand the retaining plate

finto place on the opposite side.

Reversing the door hinging

^Close the lower door.

Caution! The lower door is no longer

secured in place once the hinge

plate has been removed in the next

step.

^Remove the middle bearing pin iby

pulling it upwards.

^Carefully lift the lower door off of the

appliance and set it aside.

^Pull off the cover j.

^Unscrew the hinge plate k, turn it

180° and screw it into place on the

opposite side.

^Pull off the plastic cap h, turn it over

and fit it back onto the hinge platek.

^Attach the cover jon the opposite

side.

^Lift each of the plugs lout of the

door bushings and reinsert them on

the opposite side.

^Using a screwdriver, remove each of

the spring clips mfrom the bottom of

the door and fit them on the opposite

side.

Reversing the door hinging

Inhaltsverzeichnis

Andere Miele Kühlschrank Handbücher

Miele

Miele KFNS 37432 iD Bedienungsanleitung

Miele

Miele KF 1803 Vi Bedienungsanleitung

Miele

Miele KF 7564 S ed-1 Technisches Datenblatt

Miele

Miele K 32222 i Bedienungsanleitung

Miele

Miele KD 683 i-3 Technisches Datenblatt

Miele

Miele KF 9757 iD Bedienungsanleitung

Miele

Miele K 1911 SF Benutzerhandbuch

Miele

Miele KFN 9755 IDE Bedienungsanleitung

Miele

Miele Independence KF1901Vi Gebrauchsanweisung

Miele

Miele Independence KF1811Vi Gebrauchsanweisung

Miele

Miele KF 2811 SF Bedienungsanleitung

Miele

Miele KDN 12823 S Technisches Datenblatt

Miele

Miele KS 4783 Series Bedienungsanleitung

Miele

Miele K 851 iD Technisches Datenblatt

Miele

Miele K 9122 Ui Bedienungsanleitung

Miele

Miele KS37472iD Bedienungsanleitung

Miele

Miele KF 7650 SNE ed Technisches Datenblatt

Miele

Miele KFNS37452iDE Bedienungsanleitung

Miele

Miele KFN 4374 ED ws Bedienungsanleitung

Miele

Miele K 2316 S Technisches Datenblatt

Miele

Miele KFN 7734 F Bedienungsanleitung

Miele

Miele K 1901 SF Bedienungsanleitung

Miele

Miele KF 18 Vi Series Bedienungsanleitung

Miele

Miele K 14820 SD ed Montageanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung