MikroTik Chateau D53G-5HacD2HnD-TC&EG06-A Bedienungsanleitung

Chateau LTE6-US

Chateau LTE6-US, D53G-5HacD2HnD-TC&EG06-A

The Chateau is a home router to be used with a cellular network provider sim card.

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

The Installation of the equipment must comply with local and national electrical codes.

This unit is intended to be installed in the rackmount. Please read the mounting instructions carefully before beginning installation. Failure to use the

correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.

This product is intended to be installed indoors. Keep this product away from water, fire, humidity, or hot environments.

Use only the power supply and accessories approved by the manufacturer, which can be found in the original packaging of this product.

Read the installation instructions before connecting the system to the power source.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

Exposure to Radio Frequency Radiation:This MikroTik equipment complies with the FCC, IC, and European Union radiation exposure limits set forth for an

uncontrolled environment.This MikroTik device should be installed and operated no closer than 20 centimeters from your body, occupational user, or the

general public.

Quickstart

Please follow these quick steps to set up your device:

Connect your computer to one of the Ethernet ports;

Optional - Connect an external antenna to the SMA connector (The antennas are not provided in the package, see " ");Antenna usage

Insert a micro SIM card into the slot located under the device;

Connect the power adapter to the DC jack;

Once the device is powered on and the PC is connected to the device, open in your web browser to start the configuration;https://192.168.88.1

User name: a and there is no password by default you will be logged in automatically to the Quick Set screen;

dmin

We recommend clicking the "Check for updates" button on the right side and updating your RouterOS software to the latest version to ensure the

best performance and stability, Must have a valid SIM card inserted;

To manually update the device, please go to https://mikrotik.com/download

Choose ARM packages for this device and download them to your PC.

Upload downloaded packages to the WebFig "Files" menu and reboot the device.

Updating your RouterOS software to the latest version will ensure the best performance, stability, and security updates.

To personalize your wireless network, SSID can be changed in the fields "Network Name";

Choose your country on the left side of the screen in the field "Country", to apply country regulation settings;

Set up your wireless network password in the field "WiFi Password" the password must be at least eight symbols;

Set up your router password in the bottom field "Password" to the right and repeat it in the field "Confirm Password", it will be used to login next

time;

Click on the "Apply Configuration" to save changes.

Connecting with a mobile app

Use your smartphone to access your router through WiFi.

Insert the SIM card and power on the device.

Scan QR code with your smartphone and choose your preferred OS.

Connect to the wireless network. SSID starts with MikroTik and has the last digits of the device's MAC address.

Open application.

By default, the IP address and user name will be already entered.

Click Connect to establish a connection to your device through a wireless network.

Choose Quick setup and the application will guide you through all basic configuration settings in a couple of easy steps.

An advanced menu is available to fully configure all necessary settings.

Specifications

Product code D53G-5HacD2HnD-TC&EG06-A

CPU IPQ-4019 488-896 MHz auto

CPU architecture ARM 32bit

CPU core count 4

Size of RAM 256 MB

RAM type DDR3L

Storage 16 MB, Flash

Number of 1G Ethernet ports 5

USB 1 USB 2.0 port type A

Switch chip model IPQ-4019

Wireless 2.4 GHz 802.11b/g/n dual-chain, 5 GHz 802.11a/n/ac dual-chain

Wireless antenna max gain 2.4 GHz (3 dBi), 5 GHz (5.5 dBi)

Antenna beam width 360°

LTE category 6 (300Mbit/s Downlink, 50Mbit/s Uplink)

LTE modem EG06-A

TAC 01619900

LTE FDD bands 2 (1900MHz) / 4 (1700MHz) / 5 (850MHz) / 7 (2600MHz) / 12 (700MHz) / 13 (700 MHz) / 25 (1900MHz) / 26 (850MHz) / 29 (700

MHz) / 30 (2300 MHz) / 66 (1700MHz)

3G Category R8 (42.2Mbps Downlink, 5.76Mbps Uplink)

3G Bands 2 (1900MHz) / 5 (850MHz)

Dimensions 240 x 156 x 44 mm

Operating system RouterOS, License level 4

Operating temparature -40°C to +70°C

Mounting

The device is designed to be used indoors, by placing it on the desktop.

Powering

The device accepts power from an adapter:

Direct-input power jack (5.5 mm outside and 2 mm inside, female, pin positive plug) 12-28 V DC.

The power consumption under maximum load can reach 14.3 W, with attachments 19 W.

Configuration

We recommend checking for updates frequently to receive the latest updates for your RouterOS software to ensure the best performance and stability.

RouterOS includes many configuration options in addition to what is described in this document. We suggest starting here to get yourself accustomed to

the possibilities: . In case IP connection is not available, the Winbox tool ( ) can be used to connect to the MAC address https://mt.lv/help https://mt.lv/winbox

of the device from the LAN side (all access is blocked from the Internet port by default).

For recovery purposes, it is possible to boot the device for reinstallation, see section .Buttons and Jumpers

Mode button

Mode button is located on the back of the unit, to the right side (see " ")Expansion slots and ports

The Default configuration for the Mode button is dark mode - to turn off all LEDs. The button can be configured in RouterOS to run any user-specified

scripts.

Sync button

Sync button is located on the top of the unit. WPS Sync button, if configured on the wireless interface, can be used to connect new clients.

Press and hold the WPS button for 1 – 5 seconds to enable WPS for wireless interfaces.

Front LED status

Wireless network activity. Ethernet port activity. Power-on. LTE signal strength.

We recommend using Cat5 shielded cable. When using and installing this device please pay attention to the Maximum Permissible Exposure

(MPE) safety distance with a minimum of 20 cm between the radiator and your body.

SIM slot usage

SIM card slot is designed to use with Micro SIM cards.

Nano SIM cards have different thicknesses, and usage with an adapter are not recommended.

Reset button

The reset button has three functions:

Hold this button during boot time until the LED light starts flashing, release the button to reset the RouterOS configuration (total 5 seconds).

Keep holding for 5 more seconds, LED turns solid, release now to turn on CAP mode. The device will now look for a CAPsMAN server (total 10

seconds).

Or Keep holding the button for 5 more seconds until LED turns off, then release it to make the RouterBOARD look for Netinstall servers (total 15

seconds).

Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device.

Useful for RouterBOOT debugging and recovery.

Accessories

The package includes the following accessories that come with the device:

EU/US Switching Power Supply 24 V , 1.2 A, 28.8 W, 86.8 %, VI, cable:150 cm.

CAT5E UTP Flat Cable, 8P8C, AWG32, 1.5 m, white color.

LTE Antenna usage

The device has two external antenna connectors on the back behind the doors.

Open doors by pulling them upwards.

Screw the LTE antenna to the SMA connector located on the left side. The maximum diameter for antenna connectors or any other adapters used

is 13 mm.

Cellular connection technology based on system/power LED color:

Red: GSM

Yellow: 3G

Blue: LTE

Green: 5G NSA

Violet: 5G SA

Led not blinking: Not registered

Netinstall

When performing Netinstall, make sure to use the latest v7 version of both ROS files and the Netinstall software.

Operating system support

The device supports RouterOS software version v7.2.3 The specific factory-installed version number is indicated in the RouterOS menu /system resource.

Other operating systems have not been tested.

When using one antenna, please connect to the SMA connector on the left side (ANT1).

Only when using two antennas, you can connect to the right SMA connector (ANT4).

Please connect and disconnect the antenna, when the device is turned off!

SMA connectors on the device are female.

To avoid pollution of the environment, please separate the device from household waste and dispose of it in a safe manner, such as at

designated waste disposal sites. Familiarize yourself with the procedures for the proper transportation of the equipment to the designated

disposal sites in your area.

Federal Communication Commission Interference Statement

Model FCC ID Contains FCC ID

D53G-5HacD2HnD-TC&EG06-A TV7D53G-5ACD2ND XMR201807EG06A

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this

equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to ensure compliance.

Technical Specifications

Product Power Input Options DC Adapter Output Specification, (V/A) IP class of the enclosure Operating Temperature

DC Jack 12-28 V 24 V / 1.2 IP20 °..+70°C0

Inhaltsverzeichnis

Andere MikroTik Netzwerk-Router Handbücher

MikroTik

MikroTik Chateau 5G Series Bedienungsanleitung

MikroTik

MikroTik 922UAGS-5HPacD Bedienungsanleitung

MikroTik

MikroTik LHG 60G Bedienungsanleitung

MikroTik

MikroTik RB2011iL-RM Bedienungsanleitung

MikroTik

MikroTik RouterBOARD Groove Bedienungsanleitung

MikroTik

MikroTik RB912UAG-2HPnD Bedienungsanleitung

MikroTik

MikroTik RB800 Bedienungsanleitung

MikroTik

MikroTik L009UiGS-RM Bedienungsanleitung

MikroTik

MikroTik RB912UAG-5HPnD Bedienungsanleitung

MikroTik

MikroTik R11e-2HnD Bedienungsanleitung

MikroTik

MikroTik hAP ax lite Bedienungsanleitung

MikroTik

MikroTik SXT 6 Bedienungsanleitung

MikroTik

MikroTik RouterBOARD CCR2004-1G-12S+2XS Bedienungsanleitung

MikroTik

MikroTik RouterBOARD 711UA-5HnD Bedienungsanleitung

MikroTik

MikroTik CRS317-1G-16S+RM Bedienungsanleitung

MikroTik

MikroTik RouterBOARD 711GA-5HnD Bedienungsanleitung

MikroTik

MikroTik CRS510-8XS-2XQ-IN Bedienungsanleitung

MikroTik

MikroTik RBSXTR&R11e-LTE6 Bedienungsanleitung

MikroTik

MikroTik CSS610-8G-2S+IN Bedienungsanleitung

MikroTik

MikroTik RB1100 Bedienungsanleitung

MikroTik

MikroTik 912UAG Series Bedienungsanleitung

MikroTik

MikroTik RouterBOARD RB5009 Bedienungsanleitung

MikroTik

MikroTik RouterBOARD 951-2n Bedienungsanleitung

MikroTik

MikroTik GPEN21 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung

Dynacord

Dynacord Promatrix 6000 Bedienungsanleitung