MikroTik RouterBOARD SXT G-5HnD Bedienungsanleitung

See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 5-SEP-2011

RouterBOARD SXT G-5HnD

Quick Setup Guide and Warranty Information

The RouterBOARD SXT G-5HnD comes as a complete set, and includes a built in

802.11n dual chain wireless device, and a dual polarization 16dBi antenna. It has one

Gigabit Ethernet connector which supports MDI-X auto detection.

First use

1. Connect an Ethernet cable to the port behind the small plastic door

2. The SXT accepts 24V Passive PoE from the supplied PoE injector

3. The default IP address from LAN is 192.168.88.1 for configuration

4. Username is admin and there is no password

Powering

The board accepts powering from the Ethernet port (Passive PoE) 8-30V DC. Package

contains a 24V adapter.

Booting process

RouterOS is the operating system of all RouterBOARD routers. Please see detailed configuration guide here:

http://wiki.mikrotik.com/wiki/Category:Manual

This device doesn't come fitted with a Serial Port connector, so initial connection has to be done via the Ethernet cable, using the MikroTik

Winbox utility. Winbox should be used to connect to the default IP address of 192.168.88.1 with the username admin and no password.

In case IP connection is not available, Winbox can also be used to connect to the MAC address of the device. More information here:

http://wiki.mikrotik.com/wiki/First_time_startup

In case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET button of the device when start-

ing it until the LED LD600 light turns off (behind the small door), and SXT will start to look for Netinstall servers.

Mounting

With the clip pointed forward, slide the mounting bracket into the rail on the bottom of the case, until the clip clicks into place. The SXT

comes bundled with a hose clamp - guide the clamp through the opening in the bracket and around the pole where it will be mounted.

Tighten the hose clamp screw when alignment is complete. Two screw holes are provided as additional security against accidental bracket

movement.

The SXT device has a sliding door, behind which the Ethernet port and the reset jumpers are located. This door can be also secured shut

with a screw in the provided screw hole.

Buttons and Jumpers

RouterOS reset jumper hole (access through the plastic door) –resets RouterOS software to defaults. Must short cir-

cuit the metallic sides of the hole (with a screwdriver, for example) and boot the device. Hold screwdriver in place

until RouterOS configuration is cleared.

RouterBOOT reset button (access through the plastic door) has two functions:

Hold this button during boot time until LED light starts flashing,

release the button to reset RouterOS configuration (same result as with reset hole)

Hold this button during boot time longer, until LED turns off,

and then release it to make the device look for Netinstall servers.

See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 5-SEP-2011

Operating System Support

Currently tested operating system is MikroTik RouterOS (starting from version v5).

Copyright and Trademarks. Copyright MikroTikls SIA. This manual contains information protected by copyright law. No part of it may be

reproduced or transmitted in any form without prior written permission from the copyright holder. RouterBOARD, RouterOS, RouterBOOT

and MikroTik are trademarks of MikroTikls SIA. All trademarks and registered trademarks appearing in this manual are the property of their

respective holders.

Hardware. MikroTikls SIA warrants all RouterBOARD series equipment for the term of fifteen (15) months from the shipping date to be free

of defects in materials and workmanship under normal use and service, except in case of damage caused by mechanical, electrical or other

accidental or intended damages caused by improper use or due to wind, rain, fire or other acts of nature.

If you have purchased your product from a MikroTik Reseller, please contact the Reseller company regarding all warranty and repair issues,

the following instructions apply ONLY if you purchased your equipment directly from MikroTik Latvia

To return failed unit or units to MikroTikls you must perform the following RMA (Return Material Authorization) procedure. Follow the

instructions below to save time, efforts, avoid costs, and improve the speed of the RMA process. Take into account that all goods have one

year warranty.

Instructions are located on our webpage here: http://rma.mikrotik.com

Manual. This manual is provided “as is” without a warranty of any kind, expressed or implied, including, but not limited to, the implied

warranty of merchantability and fitness for a particular purpose. The manufacturer has made every effort to ensure the accuracy of the

contents of this manual; however, it is possible that it may contain technical inaccuracies, typographical or other errors. No liability is as-

sumed for any inaccuracy found in this publication, nor for direct or indirect, incidental, consequential or other damages that may result

from such an inaccuracy, including, but not limited to, loss of data or profits. Please report any inaccuracies found to sup-

[email protected]

See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 5-SEP-2011

Federal Communication Commission Interference Statement

(FCC ID: TV7SXTG-5HND)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa-

tion.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of

the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the

user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

This device and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter.

IMPORTANT: Exposure to Radio Frequency Radiation.

13 cm minimum distance has to be maintained between the antenna and the occupational user and 28 cm to general public.

Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be

satisfied.

Antenna Installation. WARNING: It is installer's responsibility to ensure that when using the authorized antennas in the

United States (or where FCC rules apply); only those antennas certified with the product are used. The use of any antenna

other than those certified with the product is expressly forbidden in accordance to FCC rules CFR47 part 15.204. The installer

should configure the output power level of antennas, according to country regulations and per antenna type. Professional

installation is required of equipment with connectors to ensure compliance with health and safety issues.

Inhaltsverzeichnis

Andere MikroTik Drahtloser Zugangspunkt Handbücher

MikroTik

MikroTik mAP 2nD Bedienungsanleitung

MikroTik

MikroTik wAP 60G Bedienungsanleitung

MikroTik

MikroTik Wireless Wire Cube Bedienungsanleitung

MikroTik

MikroTik wAP LR2 kit Bedienungsanleitung

MikroTik

MikroTik wAP LR8 Series Bedienungsanleitung

MikroTik

MikroTik LHG XL 52 ac Bedienungsanleitung

MikroTik

MikroTik CubeG-5ac60ay Bedienungsanleitung

MikroTik

MikroTik MANTBox 52 15s Bedienungsanleitung

MikroTik

MikroTik hAP ac2 Bedienungsanleitung

MikroTik

MikroTik cAP ac Bedienungsanleitung

MikroTik

MikroTik RBLtAP-2HnD&R11e-LTE&R11e-LR8 Bedienungsanleitung

MikroTik

MikroTik PWR-LINE AP Bedienungsanleitung

MikroTik

MikroTik LtAP RB912R-2nD-LTm&R11e-LTE-US Bedienungsanleitung

MikroTik

MikroTik RBcAPL-2nD Bedienungsanleitung

MikroTik

MikroTik RBcAPGi-5acD2nD-XL Bedienungsanleitung

MikroTik

MikroTik Cube 60G ac Bedienungsanleitung

MikroTik

MikroTik Cube Lite60 Series Bedienungsanleitung

MikroTik

MikroTik LHG Series Bedienungsanleitung

MikroTik

MikroTik hAP ac Bedienungsanleitung

MikroTik

MikroTik Cube 60G ac Bedienungsanleitung

MikroTik

MikroTik Audience Bedienungsanleitung

MikroTik

MikroTik NetMetal 5 triple Bedienungsanleitung

MikroTik

MikroTik wAP ac Series Bedienungsanleitung

MikroTik

MikroTik RouterBoard 951 Ui-2HnD Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung