Milennia HV-316 Bedienungsanleitung

HV-316 Remote Control

Microphone Preamplifier

Owner’s Manual

Millennia Media HV-316 page 2 of 17 
Table of Contents
INTRODUCTION........................... 3 
SAFETY PRECAUTIONS ................ 3 
FRONT PANEL FUNCTIONS .......... 5 
1. Unit ID Display .......................................5 
2. Power Indicator ......................................5 
3. Input Level & Phantom Power Indicator .....5 
4. Auxiliary Power ......................................5 
5. Power Switch .........................................5 
REAR PANEL FUNCTIONS ............ 5 
1. AC Power...............................................5 
2. MIDI Connection.....................................5 
3. Ethernet ................................................5 
4. Network Reset........................................5 
5. 12 Volt Redundant (Auxiliary) Power .........5 
6. Unit ID Selector......................................5 
7. Mic Inputs..............................................5 
8. Analog Output Option..............................5 
9. Reserved DB25.......................................5 
GETTING STARTED ...................... 6 
Installing the Ælogic Software ..........................6 
Setting Unit ID(s) and IP Addresses ..................7 
Setting the Host Computer’s IP Address (Windows 
10)................................................................7 
Dynamic Host Configuration Protocol (DHCP)......8 
Default Settings ..............................................8 
ÆLOGIC OPERATION ................... 9 
Unit Status Window.........................................9 
Red Icon ........................................................9 
Green Icon .....................................................9 
Flashing Green Icon ........................................9 
Purple Icon.....................................................9 
Blue Icon .......................................................9 
Gray Icon.......................................................9 
Unit ID Conflict ...............................................9 
Unit Status Dialog ...........................................9 
Overview .....................................................10 
Control Section ..........................................10 
Control Layout ...........................................10 
Unit Naming and Unit Name Dialog Box ...........11 
POLarity Flip................................................. 11 
PAD.............................................................11 
48V .............................................................11 
MUTE...........................................................11 
Channel Gain Faders/Gain Display...................11 
Meter Preferences Dialog ...............................11 
SPLIT ..........................................................11 
SAFE ...........................................................11 
RBN ............................................................11 
HPF .............................................................11 
Link Assignment ...........................................12 
Scribble Strip................................................12 
Link Matrix .................................................12 
Scene Window ...........................................13 
Project and Scene Management .................13 
Creating a Project .........................................13 
Scene Window.............................................. 13 
Safety Prompts ............................................ 13 
Creating New Scenes .................................... 13 
Renaming Scenes ......................................... 13 
Reordering Scenes........................................ 13 
Recalling Scenes........................................... 13 
Deleting Scene ............................................. 14 
Locking Scene Window Functions.................... 14 
Appending and Saving Scenes........................ 14 
Saving Scene Changes .................................. 14 
Loss of Power............................................... 14 
Setup Menu ................................................. 14 
Diagnostics .................................................. 14 
Setup System Status .................................... 14 
Soft Reset ................................................... 14 
Restart Program ........................................... 14 
APPENDIX ................................. 15 
Ælogic Keyboard Shortcuts ............................ 15 
Microphone input wiring diagram .................... 15 
SPECIFICATIONS ...................... 16 
ARCHITECTS AND ENGINEERS 
SPECIFICATION ........................ 17 
WARRANTY ............................... 17 

Page 3 of 17 rev 103020 Millennia Media HV-316

Introduction

Congratulations on your purchase of the Millennia

Media HV-316 Remote-Controllable Microphone

Preamplifier.

We will refer to both the HV-316/8 8-Channel

and HV-316 16-Channel as the HV-316 unless

there is an operational difference.

The HV-316 is the result of meticulous blind listening

tests on innumerable circuit topologies and E/M

designs. Your HV-316 is a finely tuned instrument

intended for critical professional applications —we

feel it offers the world's most sonically neutral

microphone preamplification.

Up to 16 HV-316s can be simultaneously controlled

plus an additional 16 HV-3Rs –a total of 384

channels on one system. A high-speed Ethernet

control interface makes this possible without any

significant system control latency, even if all 384

channels were to change parameters simultaneously.

Future Update: The MIDI control interface is

compatible with Avid’s Pro Tools®“PRE” remote

microphone preamplifier protocol. As defined by

Avid, up to 4 HV-316 (8 HV-316/8) units can be

simultaneously controlled with MIDI in Pro Tools.

FCC Notice Information for the User

This equipment has been tested and found to comply

with the limits for a Class A digital device, pursuant

to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference when the equipment is operated

in a commercial environment. This equipment

generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance

with this instruction manual, may cause harmful

interference to radio communications. Operation of

this equipment in a residential area is likely to cause

harmful interference in which case the user will be

required to correct the interference at his or her own

expense.

Safety Precautions

For your safety and the safety of others, be sure to

read and understand all safety and operational

instructions before attempting to use the HV-316.

WARNING: The HV-316 internal circuitry carries

lethal voltages. Carefully observe all warnings,

precautions, and instructions on the HV-316 and as

described in the instructions supplied with the unit.

Water, Moisture, and Spillage –Do not attempt

to use the HV-316 in, near, or around water or in

unusually moist environments, such as near a sink or

swimming pool. Prevent liquids or any other

materials or objects from spilling or falling into the

HV-316 unit.

Heat & Ventilation –Be sure to allow adequate

ventilation on both sides of the HV-316 and avoid

blocking the fan air intake and exit vents.

Power Sources & Power Cord Protection –The

HV-316 Power Supply should be connected to a

power source only of the type described in the

operating instructions or as marked on the Power

Supply. Route the power cord so that it is not likely

to be walked on or pinched by having objects placed

on it. Pay particular attention to plugs, receptacles,

and the point where the AC power cord exits the

HV-316.

Grounding –For your safety, it is extremely

important that the grounding pin of the 3-wire power

cable (included with 110 Volt units) be inserted into

a grounding type 3-pin power outlet. If you are

unable to insert the plug into an existing outlet,

contact an electrician to install a properly grounded

3-pin power outlet, preferably that with OFI / GFI

protection, if available.

Damage Requiring Service –This unit should be

repaired or serviced by qualified personnel

whenever:

•The AC power cord has been damaged, or

•Objects have fallen or liquid has spilled into

any HV-316 unit, or

•The unit does not function properly or

exhibits a marked change in performance,

•The unit has been abused, dropped, or

damaged, or

•The unit has been exposed to rain or

moisture.

Servicing –Lethal voltages are found inside the

HV-316 chassis. The user should not attempt to

repair or service this unit. All servicing and/or repairs

should be referred to Millennia.

If, after reading all instructions, precautions, and

warnings, you have remaining questions, please

contact Millennia directly before attempting to use

your HV-316.

The HV-316 enclosure measures approximately 17”

wide x 1.75” high x 16” deep and is designed for

mounting into a standard 1U, 19” equipment rack. If

the HV-316 is mounted in a road case or other rack

which is prone to strong vibration or shock, it is

highly recommended that the rear of the HV-316 be

supported or otherwise reinforced to withstand such

conditions.

HV-316 is designed on a common ground topology.

For high quality operation, and for your own safety

and the safety of others, do not defeat the power

cord earth grounding pin.

Millennia Media HV-316 page 4 of 17

HV-316 Front-End Protection –Millennia Music &

Media Systems enjoys a reputation for what many

top engineers and producers call the world’s most

musically accurate and dynamically uniform

microphone preamplifier —the HV-3. But this

thoroughbred design is not achieved without certain

operating criteria. To maintain top performance and

protect the HV-316’s sensitive HV-3 front-end, it is

advised that you do not insert or extract

microphones with phantom power on. Get in the

habit of waiting about ten seconds for the phantom

power to fully “ramp down” before inserting or

removing a microphone. This is good advice for

protecting your microphone investments, as well.

Any changes or modifications not expressly approved

by MILLENNIA MEDIA, FPC (Millennia) could void

your authority to operate this equipment under the

EC, ICAN, or FCC rules.

intellectual property in the HV-316 is transferred to

you.

Inspection –Inspect packing box(es), HV-316, and

cable(s) for damage, unusual marks, or shortages. It

is your responsibility to report damage, shortage, or

mis-shipments in a timely manner. Millennia and/or

its dealers will not be responsible for claims arising

from damage in shipping, nor will claims for shortage

or mis-shipments be honored, more than 10 days

after ship date.

Read this manual carefully and completely before

attempting to use the HV-316. Improper operation

could result in damage to product. It is the user’s

responsibility to understand the safe use and

operation of this device.

The shipping box of the HV-316 system will include:

•Quick Start Guide

•UL approved power cord (110 V countries only

except Japan)

The material contained in this manual consists of

information that is property of Millennia and is

intended solely for use by the purchasers of the

equipment described in this manual. Without express

written permission, Millennia prohibits the duplication

of any portion of this manual or the use thereof for

any purpose other than the operation and/or

maintenance of the equipment described in this

manual. This manual may not be duplicated in whole

or in part without the written consent of Millennia.

The HV-316 serial number is located on the rear and

bottom of each unit. We suggest that you record the

serial number in the space provided below. Refer to

it whenever you call an authorized Millennia repair

facility or the manufacturer. Make sure that you

Features and specifications subject to change

without notice.

Serial Number

__________________________________________

Purchase Date

__________________________________________

Where Purchased

__________________________________________

Page 5 of 17 rev 103020 Millennia Media HV-316

Front Panel Functions

The 3/8” thick hand-machined aluminum front panel

consists of 48 LED status indicators and a two-digit

numerical display.

Ælogic software is required to operate the HV-316.

The most current version can be downloaded at

Ælogic Weblink. Scroll down to the Downloads

section. It requires a computer running MS Windows

10 or higher.

1. Unit ID Display –Indicates unit number assigned

to preamp.

2. Power Indicator –Decimal point indicates unit

has power. It takes about 20 seconds after

power up before the Unit ID Display comes on.

3. Input Level & Phantom Power Indicator –

Green indicates levels -46 dBFS and higher. Red

indicates 0 dBFS. Amber indicates phantom

power is on.

4. Auxiliary Power –Indicates 12V auxiliary

(redundant) power source is powering unit.

5. Power Switch –Turns the unit on and off.

Rear Panel Functions

1. AC Power –IEC power inlet, 80-264 VAC 47-63 Hz

2. MIDI Connection –Allows remote control of the

HV-316 using MIDI protocol. Use with Yamaha

break-out cable ZP893500

3. Ethernet –Dante audio networking and Ælogic

control. Ælogic is only available on the Network

Primary connector

4. Network Reset –Restore to factory default

settings. Static IP address 192.168.1.221, Netmask

255.255.255.0

HV316 must be powered off.

Insert a small non-metallic object into the reset

opening on the read of the unit. You should feel a

slight click when the reset button is depressed.

Turn on the unit while continuing to hold the reset

button.

When the unit processor has reset it will display “00”

in the Unit ID display on the front of the unit.

Release the reset switch on the rear. The unit will

continue to boot.

When the ID Display switches to the selected Unit

ID, the device is ready to use. It will have the factory

profile and will be set to Static IP address

192.168.1.221, Netmask 255.255.255.0.

5. 12 Volt Redundant (Auxiliary) Power –

Connect only Millennia approved optional backup

power supply here.

6. Unit ID Selector –Address Select Rotary

Switch sets Unit ID. The front panel numeric

display changes to reflect the value selected

here. If connected to a network, the power

needs to be cycled for the change to take effect

in Ælogic.

7. Mic Inputs –Eight channels of

microphone-level input wired in the AES59/

Tascam format.

8. Analog Output Option –DB25s wired in the

AES59/Tascam format for analog outputs. This

option must be added at the factory.

9. Reserved DB25 –for future options.

Address

Unit ID

Address

Unit ID

Millennia Media HV-316 page 6 of 17

Getting Started

Millennia’s Ælogic software (Windows 10 only, other

versions may work but are not supported) is used to

control the unit and should be installed on your

computer before connecting the HV-316 to the

network. It can be downloaded at Ælogic Software

Scroll down to the Downloads section.

Installing the Ælogic Software –Turn off virus

protection software before installing. Remember to

turn the protection software on when finished.

You need to allow Ælogic all permissions to access

your network. Failing to do so will prevent the

software from seeing the Millennia Preamps

connected.

If you are using Wi-Fi®, turn it off and use the wired

Ethernet connection to be sure all the permissions

are applied to it so you connect the HV-316 directly

to your computer to initialize its IP address.

Extract the zipped files and Open

The following screen will appear.

Click on more info.

Click on Run Anyway

Click on Next

Check Accept and click on Next

Select the location to save the file and click Next

Click on Install

Click on Yes

Page 7 of 17 rev 103020 Millennia Media HV-316

Click on Finish

Select Private Network and Click on Allow Access

Setting Unit ID(s) and IP Addresses –Each

HV-316 needs to be set to its own unique Unit ID

and IP address. If units have the same ID or IP

addresses there will be a conflict and the system will

not work properly.

Set the Unit ID using the Address Select Rotary

Switch on the rear panel before connecting the HV-

316 to the computer or network.

The table below is a suggested addressing scheme.

IP Address

Unit ID

192.168.1.200

Host Computer

192.168.1.221

HV-316 ID 01

192.168.1.222

HV-316 ID 02

192.168.1.223

HV-316 ID 03

192.168.1.2nn

HV-316 ID nn

Be sure the computer’s wired Ethernet connection is

set to IP address 192.168.1.200.

There are many ways to do this and Microsoft

occasionally changes the setup menus. As of this

writing, this method allows quick IP address setting.

Setting the Host Computer’s IP Address

(Windows 10)

1. Press the Windows key and the Rkey at

the same time to open the Run box.

Type ncpa.cpl and press Enter to access

Network Connections immediately.

2. Double click on the HV-316 Ethernet Connection

to open its properties.

3. Double Click on Internet Protocol Version 4

(TCL/IPv4)

4. Select “Use the following IP addresses”.

5. Enter 192.168.1.200 in IP Address.

6. Enter 255.255.255.0 in Subnet mask.

7. Click OK and continue to exit Network

Connections.

8. Connect the Host Computer directly to the

HV-316’s Ethernet Port

9. Run the Ælogic Software.

Millennia Media HV-316 page 8 of 17

If you have everything set correctly when Ælogic

opens, the icon of the HV-316’s Unit ID in the Unit

Status window will turn green. Double click on it to

open the Unit Status dialog box.

Set the HV-316 IP address and click OK

You will lose connection if you select an IP

Address other than 192.168.1.xxx and will need

to change your computer’s IP Address to access the

network that you have chosen to use your HV-316s.

Dynamic Host Configuration Protocol (DHCP) is

also an option for “IP Address”, but we don’t

recommend using it unless you are familiar with

networking and have the proper network hardware

that supports it.

Ethernet and MIDI control cannot be used

simultaneously –only one remote control protocol

can be used in an HV-316 network.

Default Settings –The HV-316 is shipped to

startup with the default settings:

•All functions turned off (POL, PAD, 48V,

MUTE, SPLIT, SAFE, RBN and HPF).

•IP Address set to 192.168.1.221

•Netmask 255.255.255.0

•Unit ID 1

Page 9 of 17 rev 103020 Millennia Media HV-316

Ælogic Operation

Millennia’s Ælogic remote control software is

intuitive. What follows is an in-depth description of

its available functions. Refer to Appendix for a list of

keyboard shortcuts.

Unit Status Window –The example screen above

shows a Unit Status window in which seven HV-316

units (112 channels) are connected to the remote

network. The Unit Status window displays an icon of

each HV-316 unit on the network. The status of each

HV-316 is represented by its icon’s color code, as

follows:

Red Icon –“Unit ID Has a Conflict with Another

Unit”. If two or more HV-316s share the same Unit

ID number or IP address, their icons will turn red

and will show identical IDs or IP addresses until the

conflict is resolved.

Setting a Unit ID or IP address must be done locally

on each HV-316. Other errors could also cause a red

icon, such as over-temperature, power supply out of

range, other networking errors, etc.

Green Icon –“Functioning Normally”. Remote unit

functioning normally.

Flashing Green Icon –HV-3R only. “Functioning

Normally, Local Mode”. Remote unit is functioning

normally but is in the local mode.

HV-3R only: if the unit is in Local mode when Ælogic

is started, it won’t appear. Be sure to change the

unit to Remote mode so the software can recognize

the HV-3R.

Purple Icon –“Unit ID Is Offline”. A unit was

previously connected to the network and set to this

Unit ID but is missing from the network. It was

either turned off or the Ethernet was disconnected or

both.

Blue Icon –The Redundant Power Supply is

powering the unit and the internal power supply is

offline due to either failing or losing AC mains power.

Gray Icon –“Unit ID Is Inactive”. No unit is

connected to the network and set to this Unit ID.

Unit ID Conflict –If more than one unit has the

same ID number this warning will

appear. You must correct the

problem before you can continue.

Unit Status Dialog –Double left mouse click on

any icon brings up that unit’s Unit Status dialog box

displaying the following information:

1. Unit Functionality

2. 48v Monitor (HV-3R)

3. 24v Monitor (HV-3R)

4. 5v Monitor (HV-3R)

5. 3.3v Monitor (HV-3R)

6. Temperature

7. MAC Address

8. Firmware Version

9. Output Format

10. IP Address

11. Split Gain Offset

Scene Window

Unit Status Window

Control Section

Millennia Media HV-316 page 10 of 17

Overview –This is the default view. It expands

the channel control area to show multiple units.

Virtual switches are replaced by small virtual

LEDs. Link switch is replaced by link group

number only. Other attributes are shrunk to fit.

All functions remain accessible and adjustable

on the Overview Screen.

Above is a screen-shot of the OVERVIEW.

Control Section

Basic Navigation & Behavior

The channel controls are grouped into their

respective HV-316 8-channel Units. The screen

shot on the previous page shows units #1

through #7. You can left-click on any unit icon

shown in the Unit Status window to immediately

bring that unit’s channel controls into the main

screen.

Note the scroll bar at the bottom of the screen.

It allows the user to quickly scroll to any unit in

the network. You can also move the Control

Section by using the Left and Right arrow keys

on the keyboard. Pressing an arrow key once

corresponds to scrolling in that direction by one

channel strip.

HV-3R only: Ælogic is always the master control

when the unit is in Remote Mode. Any changes

made to the unit’s front panel in Local mode will

be overwritten when the HV-3R is put back into

Remote Mode.

Control Layout

The main control section, starting from the top

down, graphically represents these features:

1. Unit Name

2. Channel Number

3. Polarity Invert Button

4. Pad (20 dB Attenuator) Select Button

5. 48V Phantom Select Button

6. Mute Select Button

7. Gain fader

8. Plasma-type Metering

9. Channel Gain numeric

10. Split Gain Mode

11. Safe

12. Ribbon

13. High Pass Filter

14. Link Assignment

15. Scribble Strip

Overview

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Milennia Verstärker Handbücher

Milennia

Milennia MIL-AMP200BT Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung