Miller Electric 300 457 Bedienungsanleitung

OWNER’S MANUAL

FORM: OM-237 279C 2008−04−21

All Terrain LX Running Gear For Gas And Diesel (300 457 And 300 458)

All Terrain LX Running Gear With Never FlattTires For Gas And Diesel (300 492 And 300 493)

DANGER! −Indicates a hazardous situation which, if not

avoided, will result in death or serious injury. The possible

hazards are shown in the adjoining symbols or explained

in the text.

Beware of electric shock from wiring. Stop engine and

disconnect negative (−) cable from battery before install-

ing this kit. Reinstall all panels and covers.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury. The possible ha-

zards are shown in the adjoining symbols or explained in

the text.

Falling equipment can cause serious personal injury and

equipment damage. Use lifting eye to lift unit and properly

installed accessories only, NOT gas cylinders. Do not

exceed maximum lifting eye weight rating. Lift and sup-

port only with proper equipment and correct procedures.

NOTICE Indicates statements not related to personal injury.

Indicates special instructions.

Wear safety glasses with side shields.

OM-237 279 Page 2

1. Assembling Of All Terrain Running Gear (300 457, 300 492)

Tools Needed:

7/16, 9/16 in

3/8, 9/16 in

234

810

Ref. 803 903−H

Remove and dis-

card existing

hardware before

installing handle.

Remove paint from axle grooves

before installing retaining rings.

Gas

Model

Diesel

Model

⇓

OM−237 279 Page 3

Description (Qty)

Part

No.

Item

No.

1 220263 Assy, Handle Running Gear (1)

2 108940 Screw, 250−20x .75 Hexwhd.61d Gr5 Pld (2)

3 220375 Bracket, Crossmember (1)

4 604224 Screw, 250−20 x .75 Hexwhd .50d Stl Pld Slffmg Tap−rw (6)

5 601965 Screw, 375−16 x 1.00 Hex Hd−pln Gr5 Pld (4)

6 167788 Nut, 375−16 .56hex .34h Stl Pld Sem Cone Wshr .88d (4)

7 235790 Rail, Base Support Rh (1)

8 135418 Axle, Running Gear .750 Dia X 25.745 (1)

9 602250 Washer, Flat .812id x 1.469odx.134t Stl Pld Ansi .750 (2)

10 220709 Wheel, Rbr Tire 10.250 Od X 3.125 Wide X .750 Bore (2)

10 238572 Wheel, Rbr Never Flat 10.250 Od X 3.125 Wide X .750 Bore (2)

11 121614 Ring, Rtng Ext .750 Shaft X .085 Thk E Style Pld (2)

12 235794 Wheel, Rbr Tire 14.500 Od X 4.750 Wide X 1.000 Bore (2)

12 237725 Wheel, Rbr Never Flat 14.500 Od X 4.750 Wide X 1.00 Bore (2)

13 235792 Axle, Wheel (Large) (1)

14 235789 Rail, Base Support Lh (1)

15 152461 Nut, 250−20 .44hex .23h Stl Pld Sem Cone Wshr .65d (2)

16 197930 Label, Warning Do Not Weld On Base (2)

17 145655 Ring, Rtng Ext 1.000 Shaft X .052 Thk E Style Pld (2)

18 602251 Washer, Flat1.062idx2.000odx.134t Stl Pld Ansi 1.00 (2)

Be sure to provide model when ordering replacement parts.

Assembly:

Assemble base rails, axles, and wheels

(valve stems out).

.Install onto generator using rail

mountinghole 5 for gas models or 1 for

diesel models. Adjust to achieve prop-

er balance for application and acces-

sories.

Mount handles. Do not tighten hardware.

Install crossmember and tighten all hard-

ware.

OM-237 279 Page 4

2. Assembly Of All Terrain Running Gear With Protective Cage (300 458, 300 493)

Tools Needed:

7/16, 9/16 in

3/8, 9/16 in

Ref. 803 905−H

Remove paint from axle grooves

before installing retaining rings.

⇓

Remove and

discard exist-

ing hardware

before instal-

ling handle.

OM−237 279 Page 5

Description (Qty)

Part

No.

Item

No.

1 220260 Rail, Side (2)

2 108940 Screw, 250−20 x .75 Hexwhd .61d Gr5 Pld (8)

3 220266 Assy, Cable Holder (4)

4 220263 Assy, Handle Running Gear (2)

5 601965 Screw, 375−16 x 1.00 Hex Hd−Pln Gr5 Pld (4)

6 235790 Rail, Base Support Rh (1)

7 167788 Nut, 375−16 .56hex .34h Stl Pld Sem Cone Wshr .88d (4)

8 135418 Axle, Running Gear .750 Dia X 25.745 (1)

9 602250 Washer, Flat .812id x 1.469od x .134t Stl Pld Ansi .750 (2)

10 220709 Wheel, Rbr Tire 10.250 Od X 3.125 Wide X .750 Bore (2)

10 238572 Wheel, Rbr Never Flat 10.250 Od X 3.125 Wide X .750 Bore (2)

11 121614 Ring, Rtng Ext .750 Shaft X .085 Thk E Style Pld (2)

12 235794 Wheel, Rbr Tire 14.500 Od X 4.750 Wide X 1.000 Bore (2)

12 237725 Wheel, Rbr Never Flat 14.500 Od X 4.750 Wide X 1.00 Bore (2)

13 235792 Axle, Wheel (Large) (1)

14 235789 Rail, Base Support Lh (1)

15 604224 Screw, 250−20 x .75 Hexwhd .50d Stl Pld Slffmg Tap−Rw (8)

16 111998 Pin, Cotter Hair .120 Dia X 2.375lg X .500 Shaft (4)

17 152461 Nut, 250−20 .44hex .23h Stl Pld Sem Cone Wshr .65d (8)

18 197930 Label, Warning Do Not Weld On Base (2)

19 145655 Ring, Rtng Ext 1.000 Shaft X .052 Thk E Style Pld (2)

20 602251 Washer, Flat1.062idx2.000odx.134t Stl Pld Ansi 1.00 (2)

Be sure to provide model when ordering replacement parts.

Assembly:

Assemble base rails, axles, and wheels

(valve stems out).

.Install onto welding generator. Use

mounting hole 5 in rails. Adjust to

achieve proper balance for applica-

tion and accessories.

Mount handles. Do not tighten hardware.

Install side rails and tighten all hardware.

Install cable holders.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Miller Electric Schweißsystem Handbücher

Miller Electric

Miller Electric Bobcat 225 Bedienungsanleitung

Miller Electric

Miller Electric AUTOMATIC 1D Bedienungsanleitung

Miller Electric

Miller Electric Big Blue 400 PX Bedienungsanleitung

Miller Electric

Miller Electric 350 VS Bedienungsanleitung

Miller Electric

Miller Electric Spectrum 3080 Bedienungsanleitung

Miller Electric

Miller Electric RCT-224 Trailer Bedienungsanleitung

Miller Electric

Miller Electric Millermatic 250 Bedienungsanleitung

Miller Electric

Miller Electric GENERWELD 130 Bedienungsanleitung

Miller Electric

Miller Electric ST 44 Series Wire Feeder Bedienungsanleitung

Miller Electric

Miller Electric MMT-210A Bedienungsanleitung

Miller Electric

Miller Electric AUTO ARC MW 4150 Bedienungsanleitung

Miller Electric

Miller Electric Maxstar 150 STL Bedienungsanleitung

Miller Electric

Miller Electric Bluthunder 340 Bedienungsanleitung

Miller Electric

Miller Electric Spectrum 2050 Bedienungsanleitung

Miller Electric

Miller Electric Millermatic 140 Auto-Set Bedienungsanleitung

Miller Electric

Miller Electric LMSW Series Bedienungsanleitung

Miller Electric

Miller Electric Maxstar 152 Bedienungsanleitung

Miller Electric

Miller Electric Big Blue 600D Bedienungsanleitung

Miller Electric

Miller Electric INTEGRA 201/241 Bedienungsanleitung

Miller Electric

Miller Electric UNITOR UWI 150 Auto-Line Bedienungsanleitung

Miller Electric

Miller Electric MILLERMATIC 30B CONTROL/FEEDER Bedienungsanleitung

Miller Electric

Miller Electric SRH-503 Bedienungsanleitung

Miller Electric

Miller Electric OM-1500-4 Bedienungsanleitung

Miller Electric

Miller Electric Millermatic 150 Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung