Miller Dynasty 280 DX Bedienungsanleitung

OWNER’S MANUAL

OM-267 827A 2014−04

Dynasty280 DX

AC Independent Expansion

Read and follow the power source Owner’s Manual and labels carefully before installing, operating, or servicing unit.

Read the safety information at the beginning of the manual and in each section.

1-1. Software Expansion

Card Requirements:

.Purchased software expansion

memory card required.

1Memory Card Port

2Indicator LED

Enabling Software Expansion:

Insert card containing software expan-

sion into port.

LED indicator blinks green while ma-

chine is reading from or writing to the

card. After successfully reading from or

writing to the card, the LED switches

from blinking green to continuous

green. The machine is now ready to use

software expansion. Do not remove

card while LED is blinking green.

.Software expansion card must re-

main in memory card port to enable

software expansion.

Disabling Software Expansion:

Remove the software expansion card

from the memory card port.

Troubleshooting:

Problem: Indicator LED is continuous

red.

Remedy: Remove and reinsert card. If

problem continues, the card is bad.

Contact Factory Authorized Service

Center for a replacement card.

The memory card port uses an SD

memory card.

SD Logo is a trademark of the 3C

Company.

1-2. AC Independent Amplitude (Dynasty DX Models Only)

1 AC Waveshape Control

Press switch pad until desired function is se-

lected.

2 Encoder Control (Set Value)

3 Ammeter (Displays Value)

4 Voltmeter (Parameter Selection)

EN Amperage [EN] - Use with AC TIG only to

select electrode negative amperage value.

EP Amperage [EP] - Use with AC TIG only to

select electrode positive amperage value.

.Both Balance and AC Frequency LEDs

lightwhen either EN or EP Amperage is se-

lected.

5 AmperageControl

Average Amperage Control: Setting EN Am-

perage, EP Amperage, Balance, and Frequen-

cy values creates an average amperage. The

operator can change the average amperage

value while maintaining the same EN amper-

age to EP amperage ratio at the existing bal-

ance and frequency. To change the average

amperagevalue, press the Amperage switch

pad and turn the Encoder control. The chang-

ing average value is displayed on the ammeter.

Example:If EN Amperage is 150, EP Amper-

age is 100, Balance is 75%, and Frequency is

120,the average amperage is 138 amps. If you

press the Amperage switch pad and turn the

Encodercontrol until 69 amps is displayed, the

EN amperage is now 75 and EP amperage is

now 50. The balance remains 75%, and the fre-

quency is still 120, and the 1.5 to 1 EN amper-

age to EP amperage ratio is maintained.

150 A

1-3. AC Independent Waveshape (Dynasty DX Models Only)

.See Dynasty 280 DX Operation section in

Owner’s Manual 253086 for additional in-

formationon Accessing User Setup Menu.

The [ACEN], [ACEP] option replaces the

[AC] option.

1 Amperage Control

2 Parameter Display

Press switch pad until desired waveshape

[ACEN] or [ACEP] is displayed.

3 Setting Display

4 Encoder Control

Use Encoder to select between advanced

squarewave [ADVS], soft squarewave

[SOFT], sine wave [SINE], or triangle wave

[TRI]. The default is [SOFT].

234

USER

SOFT

ACEN

ACEP

Inhaltsverzeichnis

Andere Miller Schweißsystem Handbücher

Miller

Miller Spectrum 2050 Bedienungsanleitung

Miller

Miller XPS 350 Bedienungsanleitung

Miller

Miller Axcess E Dual Bedienungsanleitung

Miller

Miller EnPak Mechanic OM-240 113H Bedienungsanleitung

Miller

Miller OM-257 675D Bedienungsanleitung

Miller

Miller Syncrowave 250 DX Bedienungsanleitung

Miller

Miller Invision 352 MPa Auto-Line CE Bedienungsanleitung

Miller

Miller Blue Star 6000 Bedienungsanleitung

Miller

Miller TRAILBLAZER 302 AIR PAK Bedienungsanleitung

Miller

Miller M-100 Bedienungsanleitung

Miller

Miller Maxtron 450 Bedienungsanleitung

Miller

Miller DC 253 Stick Bedienungsanleitung

Miller

Miller EnPak A30 Bedienungsanleitung

Miller

Miller FieldPro Feeder CE Bedienungsanleitung

Miller

Miller XR - AlumaPro Bedienungsanleitung

Miller

Miller PipePro 450 RFC Bedienungsanleitung

Miller

Miller Gold Star Series Bedienungsanleitung

Miller

Miller DIVERSION 165 Bedienungsanleitung

Miller

Miller Delta-Fab OM-2241 Bedienungsanleitung

Miller

Miller AUTO ARC MW 4150 Bedienungsanleitung

Miller

Miller Millermatic 300 Bedienungsanleitung

Miller

Miller Bobcat 260 Diesel Bedienungsanleitung

Miller

Miller Maxstar 152 Bedienungsanleitung

Miller

Miller DYNASTY 200 DX Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE I400 Bedienungsanleitung