Miller EnPak A30 Bedienungsanleitung
Page 1
EnPak®
A30 Quick Guide
®
Page 2
Knowing your EnPak
►EnPak A30 Diesel Side View
1. Maintenance label
2. Engine Oil Fill Cap
3. Engine Oil Dip Stick
4. Engine Oil Filter
5. Engine Air Filter
6. Engine Fuel Filter
7. Air Compressor Oil Drain
8. Air Compressor Oil Fill Cap
9. Air Compressor Oil Filter
Page 3
Knowing your EnPak
►EnPak A30 Gas Side View
1. Maintenance label
2. Engine Fuel Filter
3. Engine Oil Filter
4. Air Compressor Oil Drain
5. Air Compressor Oil Fill Cap
6. Air Compressor Oil Filter
Page 4
Knowing your EnPak
►EnPak A30 Gas Top View
1. Engine Oil Dip Stick
2. Engine Air Filter
3. Air Compressor Air Filter
4. Air Compressor Coalescing Filter
5. Fuse Box Assembly
Page 5
Knowing your EnPak – Remote Panels
►Main Control Remote Panel
1. Engine Control Switch
2. Engine/Compressor Service Indicator Lights
3. Process Switch
4. Adjust control/Select Button
5. DC Voltmeter
6. DC Ammeter
7. Arc Control Meter
8. USB Receptacle
9. Setup Light
10. Glow Light
11. Charge/Weld Switch
12. Compressor Switch
Page 6
Knowing your EnPak – Remote Panels
►Weld/Battery Charge Remote Panel
1. Battery Charge Receptacle
2. Positive Weld Receptacle
3. Negative Weld Receptacle
►Auxiliary Power Remote Panel (Optional)
1. 120/240 VAC 50A Receptacle
2. 120 VAC GFCI Receptacle
Page 7
Getting Started
Before Starting Your EnPak
Make sure the emergency brake is on and there is power to the EnPak remote panel. This could be a
master switch or EnPak switch. Make sure to check all uids and belts before starting.
First Start of the Day
Turn the Engine Control Switch to the Start position and release. The EnPak warning will beep and
automatic starting sequence begins. Allow the EnPak engine to warm up before work begins.
Engine Stop
Turn Engine Control Switch to OFF position.
Auto Start/Stop Function
To enable the auto start/stop feature place the Engine Control Switch in the Auto Start/Stop position.
To disable the auto/start top feature, place the Engine Control Switch in the Auto-Speed position.
Turn the Compressor On or Off
To turn the compressor on or off, position the compressor switch in the I (on) or O (off) position.
Battery Charge Mode
To enable the battery charge/crank assist feature, place the Charge/Weld switch in the charge
position and place the process switch in the position matching voltage of the battery being charged.
Chassis Power Mode
To enable the Chassis Power feature, place the Charge/Weld switch in the charge position and place
the process switch in the Chassis Power 12 V position. When using the EnPak to keep the truck
battery charged for multiple lights or other items, use the Chassis Power mode for high amperage
applications.
Weld Mode
To enable a weld mode, place the Charge/Weld switch in the weld position and place the process
switch in the position matching the desired weld process.
Page 8
Getting Started (continued)
Process Switch
The process switch works in conjunction with Charge/Weld Switch. Use switch to select weld process
and battery charge process – see table below.
Setting a GFCI from the EnPak Generator
The GFCI must see 120 V before setting. Start the EnPak, access the service menu as described
above, select “RPM SET”. Press and release the control to access the speed menu, select “3600”,
then press and release again to save selection. This will increase engine speed to 3600 rpm’s.
Now set the GFCI. Access the service menu and select “RPM SET” again, press and release the
control to access the speed menu and select “AUTO”, then press and release again to save selection.
The engine should go back to idle speed.
Process Switch Setting Typical Process Applications (DC Only)
OUTPUT ON
Output On – GMAW/FCAW (MIG)
MIG solid wire and dual shield ux core use a voltage sensing (VS)
feeder that does not require a control cable back to the welder/gen-
erator.
Output On – FCAW-S (Electrode Negative)
No Gas
FCAW (Flux Cored Arc Welding – self shielded) uses a voltage sensing
(VS) feeder that does not require a control cable back to the welder/
generator.
Output On – SMAW (STICK XX18 and
STICK XX10) Stick welding. Strike an arc to start welding
Output On – GTAW (Lift-Arc TIG) Lift-Arc TIG: touch tungsten to work and lift to start welding. Uses
circuitry internal to the welder/generator to aid arc start.
Output On – Aluminum Aluminum solid wire uses a remote connected spoolgun accessory.
BATTERY
CHARGE
Battery Charge 12 V Battery charging or jump starting with a 12 volt system.
Battery Charge 24 V Battery charging or jump starting with a 24 volt system.
Chassis Power 12 V Powering large 12 volt loads on vehicle such as electric cranes, lights,
or vehicle systems.
Service Menu
To access the service menu, press and hold the Adjust Control/Select Button for 5 seconds, then
release. Rotate the knob to scroll through the menu items. Press and release the control to access
the options and information within each menu item.
Rotate the control to scroll or change value. Press and release control to save selection. After 5
seconds of inactivity, the menu will time out and the selection will be saved.
Codes Shown on EnPak Remote Control Panel Display
You could see a code show up on the EnPak screen to let you know there is some type of issue.
Check the manual for error code reference to help repair the issue. Resetting of Charge/Weld codes
can be done by either: changing position of the charge/weld switch; change positions of the process
select switch; cycle unit power off/on. Resetting of Air Compressor codes can be done by switching
the compressor Off, then On.
Getting Started (continued)
Menu Item
Selectable Item
Option(s) Description
HOUR MTR – – Displays the current Engine Hours.
ENG OIL
OIL HOUR Displays the current oil change countdown.
OIL SET Sets the oil change interval.
OIL RSET Resets the oil change countdown.
COMP OIL
OIL HOUR Displays the current oil change countdown.
OIL SET Sets the oil change interval.
OIL RSET Resets the oil change countdown.
RPM DISP – – Displays current engine RPM.
RPM SET
AUTO Enables auto speed function.
3600 Locks engine speed at 3600 RPM.
STOP TIME 2 to 30 min Unit idle time before auto stop (adjustable in 1 min increments).
MIN PRES 90 psi up to 10 psi less
than max pressure
Minimum pressure to start air compressor (adjustable in 1 psi
increments).
MAX PRES 175 psi down to 10 psi
greater than min pressure
Maximum pressure to stop air compressor (adjustable in 1 psi
increments).
SOFT WARE – – Displays the current revision of rmware installed.
FACT RSET
RSET YES Resets all settings to factory defaults.
RSET NO All settings remain at previous settings.
Page 10
Notes
UpFitter Information
UpFitter: ____________________________________ Location: ____________________________________
Phone: ______________________________________ Email: _______________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Andere Miller Schweißsystem Handbücher
Miller
Miller Axcess 300 Bedienungsanleitung
Miller
Miller Trailblazer 301 D Bedienungsanleitung
Miller
Miller 394F Bedienungsanleitung
Miller
Miller XMT 425 CC/CV Bedienungsanleitung
Miller
Miller Auto-Continuum 350 Bedienungsanleitung
Miller
Miller STi 270C Bedienungsanleitung
Miller
Miller DYNASTY 700 Bedienungsanleitung
Miller
Miller XMS 425 MPa CE Bedienungsanleitung
Miller
Miller AC 251 Stick Bedienungsanleitung
Miller
Miller Trailblazer 251 Bedienungsanleitung
Miller
Miller D-74DX Bedienungsanleitung
Miller
Miller XR-D Control Bedienungsanleitung
Miller
Miller Big Blue Turbo Bedienungsanleitung
Miller
Miller Dynasty 280 DX Bedienungsanleitung
Miller
Miller Dynasty 210 DX Bedienungsanleitung
Miller
Miller Gold Seal 422 Bedienungsanleitung
Miller
Miller 3000 Bedienungsanleitung
Miller
Miller Blue Star 185 Bedienungsanleitung
Miller
Miller CP-302 Bedienungsanleitung
Miller
Miller D-74 MPa Plus Bedienungsanleitung
Beliebte Schweißsystem Handbücher anderer Marken
TAFA
TAFA 30*8B35 Bedienungsanleitung
Lincoln Electric
Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung
ESAB
ESAB Buddy Arc 145 Bedienungsanleitung
CIGWELD
CIGWELD 636804 Kurzanleitung
Red-D-Arc
Red-D-Arc DC-400 Bedienungsanleitung
Hobart Welding Products
Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung
