MIMAKI JV33-130BS Montageanleitung
Supplement for the Basic Operation manual
补充说明书
MIMAKI ENGINEERING CO., LTD.
D202570-10
From the firmware Ver. 4.00, the function below were added.
Please read this manual and fully understand it before using the device.
If you have any question, contact your local distributor.
This manual correspond to the models as firmware version 4.00 or later.
When turning on the power, you can confirm the firmware version.
固件版本 4.00 以后版本，新增如下功能。
请您仔细阅读本说明，充分理解使用方法之后再使用。
如果您有不明之处，请和销售店或本公司营业所联系。
本说明书适用于固件版本4.00 以后的机型。
打开电源时，可确认到固件版本。
Perform setting to reduce stripes between passes............................................. 2
Changed contents common to all machine types ............................................... 3
弱化 Pass 间色带的设置 ................................................................................................ 4
所有机型通用变更内容 ................................................................................................. 5
ENGLISH
中文
2
Perform setting to reduce stripes between passes
In case that feeding stripes cannot be resolved even though media correction is performed, make “MAPS
(Mimaki Advanced Pass System) valid. Feeding stripes become less visible by distributing the pass boundary.
1Press the key in LOCAL.
2Press the key.
3Press the key.
4Press to select [MAPS].
5Press the key.
6Press to set ON/OFF.
• Set Value : OFF, ON
7
Press the key.
• When you select OFF, proceed to the Step 9.
• MAPS effect differs depending on the set value of the printing speed. Use it after checking effect in
advance.
• When you speed up the printing speed, it takes shorter time to print. However, MAPS effect becomes
weak.
• When you slow down the printing speed, it takes longer time to print. However, MAPS effect becomes
strong and feeding stripes become less visible.
• The resolutions and passes for which MAPS is enabled are shown in the following table.
• For conditions when MAPS is disabled, the printer operates with MAPS-OFF and print speed settings
disabled (±0%).
• MAPS may not be effective depending on image to be printed.
• Slight color change may be found.
Resolution
(dpi)
Pass Resolution
(dpi)
Pass
4 colors 4 colors
△○◎ △○◎
540x720 2 4 8, 16 720x1080 612,24
540x1080 6 12, 24 720x1440 816,32
720x720 48,16
◎: MAPS can be used when the print speed setting is within a range of ±50%, for both high speed and
standard speed.
○: At high speed, print speed is within the range of -50% to -1%. At standard speed, MAPS can be used
when the print speed is within a range of ±50%.
△: MAPS can be used when the print speed setting is within the range of -50% to -1% at standard speed
only.
FUNCT I ON
SETUP <ENT>
SETUP
SELECT : TYPE . 1
[1]
MED I A COMP . < e n t >
[1]
MAPS < e n t >
[1]MAPS
SETUP : OFF
[1]MAPS
SETUP : ON
[1]MAPS
PR I NT SPEED : 0%
3
8Press to change print speed.
•Set Value : -50 ~ +50%
(If +20% is entered, the print speed increases by
approximately 20%. If -20% is entered, the print speed
decreases by approximately 20%.)
9Press the key.
10
Press the key several times to end the setting.
Changed contents common to all machine types
Stop timer setting of deodorize fan/ drier fan
In the machine setting, we changed stop timer setting of deodorize fan/ drier fan from setting by 10 min. to by 1
min. The range of 0 to 240 has not been changed.
Cleaning intervals setting when AUTO CLEANING/ Print CLEANING is “ON”
In the user type setting, we changed max. value of cleaning intervals setting range when AUTO CLEANING/
Print CLEANING is “ON” from 10000mm to 30000mm. The default value (1000mm) has not been changed.
Recommended maximum value is 10000mm.
In case of setting cleaning intervals beyond 10000mm, nozzle missing may occur depending on the usage
environment. Please be careful.
Item Set value Outline
Machine Setup
DEODORIZE
FAN
STOP TIME 0 ~ 120 ~ 240min/
CONTINUE
Setting the time until the rotation of the exhaust
fan is interrupted after the completion of printing.
RENEW ON / OFF Switching the current operation of the exhaust
fan.
Function name Set value Outline
AUTO
CLEANING
ON INTERVAL 10 ~ 1000 ~ 30000 mm Sets the auto cleaning of the
print head every completion
of printing.
TYPE NORMAL / SOFT / HARD
OFF
Print.
CLEANING
ON INTERVAL 10 ~ 1000 ~ 30000 mm
Sets the auto cleaning of the
print head in printing.
TYPE NORMAL / SOFT / HARD
OFF
[1]MAPS
PR I NT SPEED : 1 0%
[1]
MAPS < e n t >
4
弱化 Pass 间色带的设置
若进行介质补正仍无法消除由送料所产生的色带时，请启用 “MAPS（Mimaki Advanced PassSystem）”羽化功能。
该功能可羽化 Pass 之间的界限，使送进色带变得不明显。
1在本地模式下按
2按键
3按键
4按选择[MAPS]
5按键
6按设定ON/OFF
•设定值：OFF,ON
7按键
•选择 OFF 时，进入步骤 9。
•MAPS的效果因打印速度的设定值而异。请预先进行效果确认后再使用。
•提高打印速度可缩短打印时间，但会降低 MAPS 的羽化效果。
•降低打印速度会使打印时间变长，但可增强 MAPS 的羽化效果，使送进色带变得不明显。
•以下为 MAPS 有效时的分辨率和 Pass 数。
•MAPS无效的条件是在 MAPS-OFF 或打印速度设置无效 （±0%）的状态下操作。
•根据所打印图像的不同，有不能实现 MAPS 羽化效果的情况。
•虽然可能只是一点点，但可看出颜色的变化。
分辨率
(dpi)
Pass 数分辨率
(dpi)
Pass 数
4色4色
△○◎ △○◎
540x720 2 4 8, 16 720x1080 612,24
540x1080 6 12, 24 720x1440 816,32
720x720 48,16
◎:设置为高速 /标准速时， 将打印速度设定在 ±50% 的范围内， 可进行 MAPS 操作。
○:高速时， 将打印速度设置在 -50% ～-1% 范围内。
标准速时， 将打印速度设定在 ±50% 的范围内， 可进行 MAPS 操作。
△:仅标准速时将打印速度设置在 -50 ～-1% 的范围内， 可进行 MAPS 操作。
FUNCT I ON
SETUP <ENT>
SETUP
SELECT : TYPE . 1
[1]
MED I A COMP . < e n t >
[1]
MAPS < e n t >
[1]MAPS
SETUP : OFF
[1]MAPS
SETUP : ON
[1]MAPS
PR I NT SPEED : 0%
5
8按 键，变更打印速度
•设定值 ：-50 ～+50%
(输入 +20% 时，打印速度约提高 20% ；
输入 -20% 时，打印速度约降低 20%。)
9按键
10
设定完成时，按几次 键结束
所有机型通用变更内容
设置排气扇、干燥扇的停止计时器
在机器设置中，变更了排气扇、干燥扇的停止计时器的单位设定，从 10 分钟到 1分钟。 0～240 分钟的范围没
有改变。
自动清洁、打印清洁设置为 ON 时，清洗间隔的设定
在用户类型设定中，自动清洁及打印清洁设置为 ON 时的清洗间隔设定范围的最大均从 10000mm 变为
30000mm。初始值 （1000mm）不变。
最大推荐为 10000mm, 当设置超过 10000mm 时，根据使用的环境有可能会发生喷嘴脱落，请注意。
项 目 设定值 概述
机
器
设
置
DEODORIZE
FAN
STOP TIME 0 ~ 120 ~ 240min/
CONTINUE 设置打印完成后到排风扇停止旋转的时间。
RENEW ON / OFF 切换排风扇当前的操作。
功能名称 设定值 概况
自动清洁 ON 间隔 10 ~ 1000 ~ 30000 mm
每次打印结束之后， 都要设
置打印喷头的自动清洁
类型 NORMAL / SOFT / HARD
OFF
打印清洁 ON 间隔 10 ~ 1000 ~ 30000 mm
在打印期间， 设置打印喷头
自动清洁
类型 NORMAL / SOFT / HARD
OFF
[1]MAPS
PR I NT SPEED : 1 0%
[1]
MAPS < e n t >
D202570-10-01102013
All Rights Reserved.
© MIMAKI ENGINEERING CO., LTD. NH
Andere Handbücher für JV33-130BS
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere MIMAKI Drucker Handbücher
MIMAKI
MIMAKI JV5-320DS Bedienungsanleitung
MIMAKI
MIMAKI UCJV300 Bedienungsanleitung
MIMAKI
MIMAKI JFX 200-2513 Bedienungsanleitung
MIMAKI
MIMAKI UJV100-160 Wartungshandbuch
MIMAKI
MIMAKI JFX200-2513EX Bedienungsanleitung
MIMAKI
MIMAKI Kebab MKII Bedienungsanleitung
MIMAKI
MIMAKI Textile Jet Tx3-1600 Bedienungsanleitung
MIMAKI
MIMAKI UJF-7151 plus Montageanleitung
MIMAKI
MIMAKI UJF-3042FX Bedienungsanleitung
MIMAKI
MIMAKI UJF-706 Installationsanleitung
MIMAKI
MIMAKI SWJ-320 S2 Bedienungsanleitung
MIMAKI
MIMAKI SWJ-320EA Wartungshandbuch
MIMAKI
MIMAKI ML Tiger-1800B MKII Bedienungsanleitung
MIMAKI
MIMAKI TS34-1800A Kurzanleitung
MIMAKI
MIMAKI JV33 Series Bedienungsanleitung
MIMAKI
MIMAKI UJF-3042HG Bedienungsanleitung
MIMAKI
MIMAKI jV100-160 Bedienungsanleitung
MIMAKI
MIMAKI GP-1810D Bedienungsanleitung
MIMAKI
MIMAKI JFX500-2131 Montageanleitung
MIMAKI
MIMAKI JV5-130S Bedienungsanleitung
