MIMAKI GP-1810D Bedienungsanleitung
MIMAKI ENGINEERING CO., LTD.
TKB Gotenyama Building, 5-9-41, Kitashinagawa, Shinagawa-ku, Tokyo 141-0001, Japan
Phone: +81-3-5420-8671 Fax: +81-3-5420-8687
URL: http: // www.mimaki. co. jp /
E-mail: [email protected]
Daily Care Manual
D201272
Inkjet printer is the precision machine that has highly delicate mechanism. Especially, little dust and
paper powder may have effect on a head nozzle firing ink, and may not get normal printing.
To use the inkjet printer in good condition, we recommend the following daily care.
2
3
Table of contents
Precautions during cleaning ........................................................... 4
Maintenance for frame components .............................................. 5
Washing ink from the slider surface ............................................... 5
Filling of discharge liquid at the time of starting works ............................ 6
Filling of the cleaning liquid at the end of the works ............................... 8
In case defective printing is not resolved .............................................. 10
Cleaning the wiper cap and wiper cleaner ............................................ 11
Cleaning the nozzle [Nozzle Cleaning] ................................................. 14
Ink discharge way cleaning [Drain Wash] ............................................. 17
When not in use the machine over the long term [Storage Wash] ........ 19
When the waste ink tank becomes full .................................................. 23
Replacing the flushing tray ink absorber ............................................... 24
4
Be sure to conduct maintenance works for the machine when necessary or periodically so
as to use the device for a long time while keeping its plotting accuracy.
When the machine is left unused for a long period of time
•Be sure to turn off the power of machine.
•Remove the work which setting on the table.
Precautions during cleaning
•Never disassemble the machine. Disassembling the machine can result in
electric shock hazards and breakage of the machine.
•To prevent electric shock hazard and damage to the machine, do not allow
moisture to get inside.
•Turn off power and detach power cable before doing any maintenance.
•Benzene, thinner and chemical agents containing abrasives.
Such materials can deteriorate or deform the surface of the cover.
•Do not apply lubricating oil or the like inside the machine. Such materials
can cause the printer mechanism to fail.
5
Washing ink from the slider surface
The ink may gel and collect under the slider after a long use. The ink droplets may grow in
size and smear the work as a result. To prevent this problem, wet the supplied cotton swab
in the cleaning liquid (A29) and use it to remove the ink from under the head in regular
intervals.
•Do not use the cotton swab on the head nozzles. The brush may damage
the nozzles and cause poor ink delivery.
Cleaning Tools :
• Cleaning liquid (A29)
• Cotton swabs
Routine maintenance
Maintenance for frame components
If the frame components of the machine have become dirty, wipe off frame with soft cloth
using water or neutral detergent diluted with water, squeeze it and wipe the frame compo-
nents clean. Clean the table also as dust may cause ink fly-bend or dropping.
Cleaning Tools :
• Neutral detergent
• Soft cloth (quantity)
6
Filling of discharge liquid at the time of starting works
If the discharge liquid in this machine has used in the long period, it may cause the de-
crease in the print head life. In order to prevent the shortening of the life of the head for
discharge liquid, the discharge liquid contained is replaced by cleaning liquid when it is not
used for an extended period of time. At the time of starting works, the cleaning liquid filled
in the head for discharge liquid is to be drained and the discharge liquid is filled in.
STEPS:
1. At the LOCAL state, press the
[FUNCTION] key 4 times.
2. Press the [ENTER] key.
3. Use up/down keys to select
[Discharge].
4. Press the [ENTER] key.
5. Open the station cover.
6. Turn the all valves to [DCG].
7. Close the station cover.
8. Press the [ENTER] key.
9. Fill up the discharge liquid after
initializing this machine.
10. It indicates the remaining
run-time.
FUNCTION
DCG/WASH SW <ENT>
DCG/WASH SWITCH
Fill : Discharge
Initialize
Please Wait
Filling
0 0 : ∗∗: ∗∗
SW Valve To [ DCG]
Press [ENT] Key
7
Filling of discharge liquid at the time of starting works
11.Filling of the discharge liquid is com-
pleted, menu returns to the LOCAL mode.
•Every day at the time of starting works, the filling of the discharge liquid
shall be performed.
•Every day at the time of finishing works, the filling of the cleaning liquid
shall be performed for the protection of head for discharge liquid.
page 8
<< LOCAL >>
X =1010 Y = 1860
8
Filling of the cleaning liquid at the end of the works
If you leave the head for discharge liquid with discharge liquid filled in for a long time, the
life of the head for discharge liquid will be shortened because the discharge liquid melts the
water-shedding part. To prevent the reduction of its life, when it is not used for an extended
period of time, drain the discharge liquid and fill in the cleaning liquid.
STEPS:
1. At the LOCAL state, press the
[FUNCTION] key 4 times.
2. Press the [ENTER] key.
3. Use up/down keys to select
[Washing].
4. Press the [ENTER] key.
5. Open the station cover.
6. Turn the all valves to [WASH].
7. Close the station cover.
8. Press the [ENTER] key.
9. Fill up the cleaning liquid after
initializing this machine.
10. It indicates the remaining
run-time.
Initialize
Please Wait
Filling
0 0 : ∗∗: ∗∗
FUNCTION
DCG/WASH SW <ENT>
DCG/WASH SWITCH
Fill : Washing
SW Valve To [WASH]
Press [ENT] Key
9
Filling of the cleaning liquid at the end of the works
11. Filling of the cleaning liquid is completed,
menu returns to the LOCAL mode.
•Every day at the time of finishing works, the filling of the cleaning liquid
shall be performed for the protection of head for the discharge liquid.
•Every day at the time of starting works, the filling of the discharge liquid
shall be performed. page 6
<< LOCAL >>
X =1010 Y = 1860
10
In case defective printing is not resolved
When the station interior is severely contaminated or defective printing is not fixed after
cleaning the head cleaning function. ( Operation Manual page 2.12)
Clean the suction nozzle and cap using the cleaning kit as follows,
Cleaning liquid bottle kit (A29), Gloves, Cleaning swab, Goggles
•When cleaning the ink station and head, be sure to wear the supplied
goggle and gloves to protect you from hazardous ink.
•Do not use alcohol or water.
•Do not move the carriage out of the capping station by hand. Use the
appropriate operation key to move the carriage.
The examples of defective printing
These following examples indicate improper head (nozzle) firing by dust, which effect
printing. Confirm the nozzle condition periodically before or during outputting not to use in
such as this condition. The nozzle condition can be confirmed with [test print] in this ma-
chine.
Deflection Nozzle out
Ink dropping Satellite
Inhaltsverzeichnis
Andere MIMAKI Drucker Handbücher
MIMAKI
MIMAKI CJV150 series Technisches Handbuch
MIMAKI
MIMAKI TS30-1300 Bedienungsanleitung
MIMAKI
MIMAKI TS500P-3200 Bedienungsanleitung
MIMAKI
MIMAKI UJF-7151plus Konfigurationshandbuch
MIMAKI
MIMAKI CJV300-130 Bedienungsanleitung
MIMAKI
MIMAKI CJV300-130 Wartungshandbuch
MIMAKI
MIMAKI SUJV-160 Wartungshandbuch
MIMAKI
MIMAKI UJV500 Bedienungsanleitung
MIMAKI
MIMAKI JV3 Series Bedienungsanleitung
MIMAKI
MIMAKI SIJ-320UV Wartungshandbuch
MIMAKI
MIMAKI UJF-A3MkII Series Bedienungsanleitung
MIMAKI
MIMAKI JV5-130S Leitfaden
MIMAKI
MIMAKI UJV100-160 Wartungshandbuch
MIMAKI
MIMAKI UJV100-160 Wartungshandbuch
MIMAKI
MIMAKI JV150 Series Bedienungsanleitung
MIMAKI
MIMAKI JV33-160 Bedienungsanleitung
MIMAKI
MIMAKI JV33-160A Betriebsanleitung
MIMAKI
MIMAKI fine Cut 3 Bedienungsanleitung
MIMAKI
MIMAKI UCJV300 Bedienungsanleitung
MIMAKI
MIMAKI JFX 200-2513 Bedienungsanleitung
