Mindeo CS2190 Bedienungsanleitung

Note: 1. See user manuals for more information. 2. For better readability, please print this document with laser printer. 3. Version: CS2190_QG_EN_V1.3.

CS2190 Cordless Laser Scanner Quick Guide

Notice

Parts of the handheld unit

①Exit window ②Trigger (Press to triggr / Long press 2 seconds to turn on)

③Beeper ④Power indicator (Blue LED) ⑤Successful decoding indicator (Green

LED) / Communication fail indicator (Red LED) / Charging (Red LED)

Parts of the cradle

⑥Power indicator (Blue LED)

⑦Communication indicator (Green LED)

⑧Key (Long press 2 seconds to restore factory default

setting of cradle)

Installation of cradle

1. Switch off power of the host. Refer to the below pictures, connect the host with the scanner with

different cables firstly, and then connect the adaptor to the power socket.

2. Ensure that all connections are secure. Switch on the power of the host. After a few seconds, if

only the blue LED on the cradle is ON, it indicates the cradle is in normal working mode.

USB cable

RS232 cable

PS/2 keyboard cable

Charge battery

1. Please charge the battery before the first time of use. The

charge indicator (Red LED) on the handheld unit is turned on

when the charging is in process. When the charging process

completes, the charge indicator (Red LED) is turned off.

2. Charging time: 4 hours for fully charged.

3. You can charge the battery via a USB port on the device or an

optional 5V adapter.

Indication of handheld unit for wireless data transmission

Successful Transmission

Beeper

Red LED

Vibration

Yes

Off

Three beeps

Blinks 3 times,

and then turns off

Short vibrates 3 times,

and then turns off

Programming instruction and example

Scan “SETUP”

Scan “Option barcode”

Scan “the 1st character of option”

Scan “the 2nd character of option”

Scan “END”

Example: to set Flow control to be XON/XOFF.

Initialization settings and information display

Initialize all parameters of handheld unit

Initialize all parameters of cradle

Handheld unit firmware version display

Cradle firmware version display

Handheld unit radio setting display

Cradle radio setting display

Turn off handheld unit Note

Note: 1) If you want to turn on the handheld unit again, please keep the trigger key being pressing for

2 seconds. 2) If you want to turn off the handheld unit via trigger key, please press and hold the

trigger key, after the laser beam turns off, wait for another 5 seconds, the handheld unit will be turned

off, then you can release the trigger key at this moment.

A standard kit contains: a handheld unit, a cradle, a USB cable, and a CD-ROM (containing

software and manuals).

It is suggested to read the user manual in details before use.

Note: 1. See user manuals for more information. 2. For better readability, please print this document with laser printer. 3. Version: CS2190_QG_EN_V1.3.

Notes about radio communication

1. If multi-clusters are working in the same area, it is strongly recommended that different radio

frequency channel numbers are applied to different clusters. While setting up, only the radio

frequency channel number of the first handheld unit of a single cluster is required to be set.

2. In order to obtain constantly good communication quality, when in multi-clusters working mode,

the physical space between two cradles is required to be at least 2 meters. And it is recommended

to place the cradle on a higher location, generally more than 1 meter above the ground. If

working outdoor, the higher location the better.

Quick setting to wireless network

1. Make sure that both the handheld unit and the cradle are in normal working mode. Normally it

means that only the blue LED on the handheld unit and only the blue LED on the cradle are ON as

shown below.

2. Use the handheld unit to scan the following setting barcode.

Quick binding

3. The blue LED on the handheld unit will blink and the beeper will beep regularly to indicate that the

handheld unit is ready to be positioned onto the cradle.

4. Firmly position the handheld unit onto the cradle within 15 seconds. Two short beeps will be

emitted to indicate a successful setting; otherwise, two long beeps and a short beep will be emitted to

indicate a failed setting.

Vibration indication

Disable

Enable*

Note: the factory default settings are indicated with asterisks (*).

Beeper indication

Disable

Enable*

Volume of beeper

Low

Middle

High*

Andere Handbücher für CS2190

Andere Mindeo Barcode-Lesegerät Handbücher

Mindeo

Mindeo CS3290 Bedienungsanleitung

Mindeo

Mindeo MD22 Series Bedienungsanleitung

Mindeo

Mindeo MS3390 Bedienungsanleitung

Mindeo

Mindeo MP8600 Bedienungsanleitung

Mindeo

Mindeo MD52 Series Bedienungsanleitung

Mindeo

Mindeo MP8200 Bedienungsanleitung

Mindeo

Mindeo MP82 Series Bedienungsanleitung

Mindeo

Mindeo MD6600 Bedienungsanleitung

Mindeo

Mindeo MP8608 Bedienungsanleitung

Mindeo

Mindeo MD6100S Bedienungsanleitung

Mindeo

Mindeo CS2290 Bedienungsanleitung

Mindeo

Mindeo CS-I Series Bedienungsanleitung

Mindeo

Mindeo FS380 Bedienungsanleitung

Mindeo

Mindeo MD6000 Bedienungsanleitung

Mindeo

Mindeo ES168 Bedienungsanleitung

Mindeo

Mindeo MD20 series Bedienungsanleitung

Mindeo

Mindeo MD65 Series Bedienungsanleitung

Mindeo

Mindeo MP80 Series Bedienungsanleitung

Mindeo

Mindeo MD6850 Bedienungsanleitung

Mindeo

Mindeo FS580 Bedienungsanleitung

Mindeo

Mindeo MD6000 Bedienungsanleitung

Mindeo

Mindeo CS3290-2D Bedienungsanleitung

Mindeo

Mindeo MD20 series Bedienungsanleitung

Mindeo

Mindeo MD61 Series Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung