Mindray DP-8800plus Bedienungsanleitung

Schematic Plan for DP-8800plus/DP-8600 Part Installation

Figure 1 Schematic Plan of Part Installation (with 14” monitor)

Figure 2 14” Monitor Assembly

1. transducer holder C

2. transducer holder D

3. ultrasound gel holder

4. hexagon socket screw

M5×35/spring washer Φ5/plain

5. pushing handle

6. limit screw M5×16/spring washer

Φ5

7. transducer cable hook

8. screw M4×8

9. rear cover of monitor

10. screw M4×8

11. monitor assembly

12. neck cover

13. main unit

1. limit screw

2. cable strap

3. screw M4×8

4. rear cover of monitor

5. power cable

6. signal cable

7. monitor

8. friction pad

9. neck cover

Operating procedures are shown as follows:

I. Installing the monitor

1. As shown in the figure, prior to installation of the monitor, place the neck cover on the neck

of the main unit, and place the friction pad on the rotating axis.

2. Thread the power cable and signal cable through the axis, and then place the rotating axis

into the axile bush. Connect the cables to the connectors, tighten the cables, and fix the

cables by the cable strap at the bottom of the monitor.

3. Install the rear cover of the monitor and tighten it with three M4X8 screws.

4．Fix the neck cover with M4X8 screws.

5．Tighten the limit screw on the neck.

6．After installation of the monitor, remove the protecting film on the screen.

II. Installing the pushing handle

Take out the pushing handle and three sets of hexagon socket screws M5x35/spring

washers Φ5/plain washers Φ5, and then use the M5 hexagon socket wrench to fix the

pushing handle in position.

III. Installing transducer cable hook and holder

Take out the transducer cable hook and holder, and place them in position.

VI. Installing the transducer

1．Unlock the lever of the transducer connector, put the cable upward, and insert the

connector vertically into the socket.

2．Turn the lever clockwise 90°.

3．Check that the connector is tightened.

Installation of the transducer is shown in figure 3.

Figure 3 Installing and Removing the Transducer

Schematic Plan for DP-9900plus/DP-9900/DP-9600 Part

Installation

Figure 4 Schematic Plan of Part Installation

Operating procedures are shown as follows:

I. Installing the monitor

1. As shown in the figure, prior to installation of the monitor, place the neck cover on the neck of

the main unit, and place the friction pad on the rotating axis.

2. Thread the power cable and signal cable through the axis, and then place the rotating axis

into the axile bush. Connect the cables to the connectors, tighten the cables, and fix the

cables by the cable strap at the bottom of the monitor.

3. Install the rear cover of the monitor and tighten it with three M4X8 screws. Fix the neck cover

with screw M5×16 and spring washer Φ5.

1. main unit

2. transducer holder B

3. ultrasound gel holder

4. neck cover washer Φ5

5. monitor assembly

6. screw M4x8

7. rear cover of monitor

8. screw M4×8

9. transducer cable hook

10. limit screw M5×16/spring

washer Φ5

11. pushing handle

12. hexagon socket M5x35/spring

washer Φ5/plain washer Φ5

13. transducer holder A

II. Installing the pushing handle

Take out the pushing handle and three sets of hexagon socket screws M5x35/spring washers

Φ5/plain washers Φ5, and then use the M5 hexagon socket wrench to fix the pushing handle in

position.

III. Installing transducer cable hook and holder

Take out the transducer cable hook and holder, and place them in position.

VI. Installing the transducer

1．Unlock the lever of the transducer connector, put the cable upward, and insert the

connector vertically into the socket.

2．Turn the lever clockwise 90°.

3．Check that the connector is tightened.

Figure 5: Unlocking and Locking the Transducer

Locking status

Unlocking status

P/N:9906-20-71452(V1.1)

Andere Handbücher für DP-8800plus

Dieses Handbuch passt für folgende Modelle

Andere Mindray Diagnosegeräte Handbücher

Mindray

Mindray DC-80 Bedienungsanleitung

Mindray

Mindray Z50S Bedienungsanleitung

Mindray

Mindray DP-8800plus Bedienungsanleitung

Mindray

Mindray Zonare ZS3 Bedienungsanleitung

Mindray

Mindray DP-10 Bedienungsanleitung

Mindray

Mindray TEX20 Bedienungsanleitung

Mindray

Mindray DP-50 Bedienungsanleitung

Mindray

Mindray DP-60 Bedienungsanleitung

Mindray

Mindray TEX20 Bedienungsanleitung

Mindray

Mindray Zonare ZS3KP Elite Bedienungsanleitung

Mindray

Mindray MX7 Bedienungsanleitung

Mindray

Mindray MX7 Bedienungsanleitung

Mindray

Mindray Resona R9 Bedienungsanleitung

Mindray

Mindray M7Vet Kurzanleitung

Mindray

Mindray DP-8800plus Bedienungsanleitung

Mindray

Mindray DC-90 Bedienungsanleitung

Mindray

Mindray Z60T Bedienungsanleitung

Mindray

Mindray DC-6 Bedienungsanleitung

Mindray

Mindray Resona 7T Bedienungsanleitung

Beliebte Diagnosegeräte Handbücher anderer Marken

Autel

Autel MaxiProgrammer 201 Bedienungsanleitung

TEXA

TEXA TMD2 Bedienungsanleitung

Autel

Autel MaxiIM IM608 Bedienungsanleitung

Sealey

Sealey BT2012 Bedienungsanleitung

Diagnoptics

Diagnoptics Age Reader Bedienungsanleitung

LAUNCH TECH

LAUNCH TECH X-431 PRO5 Bedienungsanleitung

Hella Gutmann

Hella Gutmann Mega macs X Bedienungsanleitung

Foxwell

Foxwell I80TS Bedienungsanleitung

KaVo

KaVo 3D eXam Bedienungsanleitung

ATEQ

ATEQ VT46 Bedienungsanleitung

Hella Gutmann

Hella Gutmann mega macs X Bedienungsanleitung

Autel

Autel MaxiFlash VCMI Bedienungsanleitung

Qiagen

Qiagen QIAcube Connect MDx Bedienungsanleitung

Alber

Alber BDSU Bedienungsanleitung

St. Jude Medical

St. Jude Medical QUANTIEN Bedienungsanleitung

Bosch

Bosch DCU 100 Bedienungsanleitung

Launch

Launch CNC-602A Bedienungsanleitung

Innova

Innova 3568 Bedienungsanleitung