Mingda Magician X2 Bedienungsanleitung
Instructions for quick assembly
V1.1
Magician X2
CONTENTS
Accessories
Assemble
Auto-leveling
Preheat
Insert the Filament
Printing
Z-offset adjust
Software Instructions
----------------------------------------------------------- 01
------------------------------------------------------------ 02
------------------------------------------------------- 06
--------------------------------------------------------------- 07
----------------------------------------------- 08
----------------------------------------------------------------- 09
----------------------------------------------- 11
------------------------------------------------------- 10
Accessories
01
Toolkit
The Main Chassis
Gantry
21 Filament 43
User manual Filament holder
Power cable
SD card Wrench
56 7 8Allen wrench
M4*20 (4pcs)
M5*25 (2pcs)
Nozzle
910 11 Teflon tube
12 13
M3*8 (2pcs)
Extruder
M4*10 (2pcs)
Assemble
Step 1 Install the gantry
Note: To avoid bending the lead screw
and effect the printing model, don't touch
or twist the lead screw when take out the
gantry from the package.
02
M5*25 (2pcs)
Note: The power supply has been
adjusted according to the local voltage.
If you need to adjust the voltage, please
follow the picture to operate it.
Step 2 Install the fixing plate screw
Step 3 Install the Filament Holder
03
M4*20(4pcs)
The filament holder can be installed left and right
04
Step 4 Connect Cable
Hotbed cable Z Motor 1 cable
Note: If you find there is a little shaking on extruder,bed or X-axis, don't worry, this is caused by long-term
transportation. Please refer to the adjustment video link in the SD card to adjust, it is helpful.
M3*8(2pcs)
Z Motor 2 cable Arranging Wire
Step 5 Install the Extruder
1.Push the extruder parallel into the
support, make sure the screw holes
on the top of the extruder are
aligned with the screw holes on the
support.
2.Use M4*10 screws to fix the
extruder on the support.
3.Connect the ribbon cable to the
port on the right side of the
extruder.
M4*10(2pcs)
05
06
Auto-leveling
Plug in the cable and turn on the
power
The printer will start auto-leveling after
preheat.
Click “Leveling” on main interface
Nota: le informazioni sull'interfaccia utente sono solo per riferimento, l'interfaccia utente effettiva potrebbe essere diversa.
07
Preheat
Nota: le informazioni sull'interfaccia utente sono solo per riferimento, l'interfaccia utente effettiva potrebbe essere diversa.
Click “preheat” on the main
interface
According to your filament, select
appropriate settings
08
Insert the filament
Nota: le informazioni sull'interfaccia utente sono solo per riferimento, l'interfaccia utente effettiva potrebbe essere diversa.
In order to feed filament smoothly,
Please keep the end of the filament
at 90°.
Insert SD card
Click “load” to feed the
filament until the filament is
out of nozzle.
Andere Handbücher für Magician X2
1
Inhaltsverzeichnis
Andere Mingda 3D-Drucker Handbücher
Mingda
Mingda Magician Pro Bedienungsanleitung
Mingda
Mingda MD-600D Bedienungsanleitung
Mingda
Mingda Magician X Bedienungsanleitung
Mingda
Mingda Rock 3 Bedienungsanleitung
Mingda
Mingda MD-D01 Bedienungsanleitung
Mingda
Mingda MD-400D Bedienungsanleitung
Mingda
Mingda MD-16 Bedienungsanleitung
Mingda
Mingda Magician X Montageanleitung
Mingda
Mingda Magician X2 Bedienungsanleitung
Mingda
Mingda Goldfish X Bedienungsanleitung
