Minicom 0SU70033 Bedienungsanleitung

PX Serial - Quick Start Guide

1. Introduction

To take advantage of the full range of features, we recommend you read the softcopy

User Guide after performing the Quick Start procedure. It’s in PDF format on the

supplied CD or on our website www.minicom.com in the Support section.

PX Serial is a one-port RS232/422/485 to Redundant Ethernet device server. PX

Serial can be configured by a web browser in https, or SSH console. Additional

management features include SNMP support and email alerts.

2. The PX Serial components

The package includes:

1 PX Serial unit

1 Power adapter (100-240VAC)

Mounting kit foot pads

Minicom CD

1111 W. 35th Street, Chicago, IL 60609 USA

www.tripplite.com/support

PX SERIAL

3. PX Serial ports

Hardware reset button

RS232/422/482 port, DB9M 15KV

ESD for all signals Speed:110 bps

to 460.8kbps

Long distance RS422 /485

120 Ohm termination

dipswitches

Figure 1 PX Serial ports side

Redundant Dual 10/100M Ethernet

Auto MDI/MDIX Auto-

Recovery<200ms Built-in 1.5KV

magnetic isolation

9-30 VDC Power

Jack

12-48 VDC Terminal

Block

Figure 2 PX Serial ports side 2

QUICK START GUIDE

4. PX Serial LEDs

LED Color Indication

PWR 1 Red On: Power 1 is on and booting up.

Blinking: Indicates an IP conflict, or DHCP or BOOTP server did not respond

properly.

Green On: Power is on and functioning normally.

Blinking: Located by Administrator’s Location function.

Off Power is off, or power error condition exists.

PWR 2 Red On: Power 2 is on and booting up.

Blinking: Indicates an IP conflict, or DHCP or BOOTP server did not respond

properly

Green On: Power 2 is on and functioning normally.

Blinking: Located by Administrator’s Location function.

Off Power is off, or power error condition exists.

Eth 1 Orange Blinking: 10 Mbps Ethernet connection.

Green Blinking: 100 Mbps Ethernet connection.

Off Ethernet cable is disconnected, or has a short.

Eth 2 Orange Blinking: 10 Mbps Ethernet connection.

Green Blinking: 100 Mbps Ethernet connection.

Off Ethernet cable is disconnected, or has a short.

Serial Orange Serial port is receiving data.

Green Serial port is transmitting data.

Off No data is being transmitted or received through the serial port.

5. Connecting the PX Serial

Connect the PX Serial to the power supply, the Network switch and Serial device as

explained below.

5.1 Connecting the Power supply

You can connect the PX Serial to the Power supply using the Terminal Block

(PWR1) and/or the Power Jack (PWR2). If both power inputs are connected, the PX

Serial is powered from the highest connected voltage. The PX Serial will only send a

loss of power alarm when power fails at both PWR1 and PWR2.

PX SERIAL

5.1.1 Terminal Block (PWR1)

1. Insert the positive and negative wires of your DC supply into the V+ and V-

contacts of the terminal block connector – see below.

(GND / V- / V+)

2. Tighten the terminal screws to prevent the DC wires from coming loose – see

below.

Once connected to the power supply, Power 1 LED turns red to show unit booting

up. When the unit is ready and if the IP setting is running correctly, the LED turns

green.

5.1.2 Power Jack (PWR2)

Connect the supplied 12VDC power adapter, or 24VDC power input to the power

jack. Power 2 LED turns red to show unit booting up. When the unit is ready and if

the IP setting is running correctly the LED turns green.

5.2 Connecting to the network switch

Connect the PX Serial to the network switch via the LAN 1 or LAN 2 port using a

standard 10/100M Ethernet cable. The Ethernet interface supports auto MDI/MDIX.

The relevant LAN 1 or LAN 2 LED turns orange for 10M Ethernet or green for

100M Ethernet.

Both Ethernet ports 1 and 2 can be connected to different switches. If both ports are

connected when the device starts up then Ethernet port 1 is the master and Ethernet

port 2 is the backup. But if when the device starts up only Ethernet port 2 is

connected, then Ethernet port 2 remains the master port.

5.3 Connecting to the Serial device

Connect the Serial device to the DB9M port. The DB9M pin-out appears in the

softcopy User Guide.

QUICK START GUIDE

5.4 Configuring the dipswitches

The Long-Range Termination dipswitches can configure 120 Ohm termination for

RS422 / 4-wire RS485 / 2-wire RS485. Set the dipswitches according to the

following table.

Dipswitch 1

Dipswitch 2

Configuration

ON ON 120 Ohm terminator for long distance 4-wire RS485 / RS422

ON OFF Don’t use this setting - it will cause errors!

OFF ON 120 Ohm termination for long distance 2-wire RS485

OFF OFF (Default) No termination for RS232/422/485 (short distance)

6. Configuring the PX Serial unit

The PX Serial unit can be managed by a Web interface, providing secure SSL

communication over the internet. The PX Serial comes with the default IP address

192.169.10.2 - this appears on the underside of the PX unit.

To display the Web interface:

1. Open your Web browser.

2. Type in the IP address of the PX Serial and press Enter.Note! The IP address

must begin with https:// and not http://. The web interface appears, see Figure 3.

Bookmark it for easy reference.

Figure 3 Overview page

The Overview page gives details of the current IP address, MAC address and

firmware version. The MAC address is also shown on the underside of the unit.

From the menu click Server Configuration to display a sub-menu.

PX SERIAL

6.1 Network Setting

Consult your Network Administrator for the network settings.

Click Network Setting, the following appears.

Figure 4 Network Setting

On this page you configure for the PX:

IP Configuration – DHCP or static

IP address

Netmask

Gateway

DNS servers

For dynamic IP address reporting at defined time intervals, fill in the Auto IP report

fields.

7. Port Configuration

Port Configuration covers Serial Parameter settings, such as baud rate, data bits, stop

bits, parity, and flow control.

From the menu click Port Configuration to display a sub-menu.

QUICK START GUIDE

7.1 Serial Setting

Click Serial Setting, the following appears.

Figure 5 Serial Setting

Port Alias: Give the port an identifying name to be identified by the connected

device.

Select the Interface: RS232 / RS422 / RS485 (2-wires) / RS485(4-wires)

Select the settings for Baud rate, Data Bits, Stop Bits, Parity and Flow Control.

Force TX interval time is to specify a timeout when no data has been transmitted.

When the timeout is reached or TX buffer is full (4K Bytes), the queued data will be

sent. Zero (factory default) means disabled.

Performance options: Select Throughput for the fastest possible transmission speed.

Select Latency for the shortest response time.

PX SERIAL

7.2 Port Profile

Click Port Profile, the following appears.

Figure 6 Port Profile

For advanced data packing options, you can specify delimiters for Serial to Ethernet

and / or Ethernet to Serial communications.

You can define up to a maximum of 4 delimiters (00~FF, HEX) for each way. The

data will be held until the delimiters are received or the optional “Flush Ethernet to

Serial data buffer” times out. Zero means disable (factory default).

8. Operating the device

Once configured, use a Telnet console or similar application - PuTTY, Tera Term,

Secure CRT - to connect to the PX Serial and operate the Serial device. Connect via

the telnet software to the PX IP address to port 4000.

For the rest of the configuration and operating instructions please see the softcopy

User Guide on the supplied CD or on our website

http://www.minicom.com/supportuserguides.htm

201205037 • 933210_EN

Andere Handbücher für 0SU70033

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Minicom Schalten Handbücher

Minicom

Minicom Smart CAT5 Bedienungsanleitung

Minicom

Minicom PX Bedienungsanleitung

Minicom

Minicom 0SU70033 Bedienungsanleitung

Minicom

Minicom 0SU70017 Bedienungsanleitung

Minicom

Minicom Smart 4 Bedienungsanleitung

Minicom

Minicom Smart CAT5 Bedienungsanleitung

Minicom

Minicom 0SU70050 Bedienungsanleitung

Minicom

Minicom Smart CAT5 Bedienungsanleitung

Minicom

Minicom 0SU70030 Leitfaden

Minicom

Minicom 1SU70017 Bedienungsanleitung

Minicom

Minicom Switches Bedienungsanleitung

Minicom

Minicom 0SU52015 Bedienungsanleitung

Minicom

Minicom PHANTOM MX IP Bedienungsanleitung

Minicom

Minicom PHANTOM MX II Bedienungsanleitung

Minicom

Minicom RJ-45 Bedienungsanleitung

Minicom

Minicom 0SU70068 Bedienungsanleitung

Minicom

Minicom Smart CAT5 Switch 16 IP Bedienungsanleitung

Minicom

Minicom 0SU52016 Bedienungsanleitung

Minicom

Minicom Minicom Smart 216 Bedienungsanleitung

Minicom

Minicom MINICOM 232 IP Bedienungsanleitung

Minicom

Minicom Minicom Smart 216 Bedienungsanleitung

Minicom

Minicom Smart CAT5 Bedienungsanleitung

Minicom

Minicom 0SU52016 Bedienungsanleitung

Minicom

Minicom Supervisor MU Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung