Minuteman E Ride 30 Bedienungsanleitung

Service Manual

for the

E Ride 30

Training

Trouble Shooting

djustments

Contents

1. Remarks 4

2. General 5

2.1 Settings 6

2.2 Brief description 7

2.2.1 Vacuuming OFF/soiled water tank full 8

2.2.2 Initial position of machine

3 Check and set machine type LDS and options

Check

and

set

machine

type

LDS

and

options

view and delete last error 11

3.1 Check and set machine type 15

3.2 Check and set options 16

33CheckandsetLSD

Check

and

set

LSD

3.4 View and delete last error in display 20

4. Program variuous cleaning cycles as a function of drive

potentiometer setting (check and set) 21

5. Pro

ram functions 23

Contents

6. Particular settings according to customer’s requirements

(last error display and water stage selection)

(last

error

display

and

water

stage

selection)

6.1 Display of last error 36

6.2 Water stage when start scrubbing 37

6.3 Water stage when start cleaning with green H Minuteman key 38

6.4

Water stage when start cleaning with green bordered key

6.4

Water

stage

when

start

cleaning

with

green

bordered

key

(increased brush pressure) 39

7. Settings on power electronic (A2) 40

8. Water pump 41

8.1 Water pump standstill recognition 43

9. Diagnosis LED for drive module 44

9.1 Signal measuring at the drive control unit 50

9.2 Settings at the accelerator pedal 57

9.2 A4:X51 plug assignment 62

Error reference chart with information on service display

Error

reference

chart

with

information

service

display

11. Adjustment of disk brake 76

12. Wiring Diagrams 77

13. Notes 81

1. Remarks

•Caution:

•Before working at the machine make sure that the batteries are disconnected

(disconnect battery plug); except for cases of current and voltage measurements.

•When replacing the stripe fuses only loosen the screws. Do not remove them

completely to avoid short-circuit hazard.

Place the new stripe fuses completely i.e. evenly under the screws.

•Measure starting and operating voltage after any repair action to detect any

eventual defect.

•

The applicable safety and accident prevention guide lines should be followed

The

applicable

safety

and

accident

prevention

guide

lines

should

followed

when servicing the machine.

2. General

•The Minuteman E Ride 30 uses a service display integrated in the hour meter

display. When turning the key switch ON, a 4-digit display will appear for about 3

seconds, describing the software version (e.g. 3.017), then another 4-digit display may

appear which repeats the last error, followed by the hour meter display.

•In case of malfunction during operation, a red error LED alights and a buzzer sounds.

The actual error code (4-digit number in the service display) with flashing dots

between the numbers will appear in the service display. Only if these criteria are

fulfilled the error is actual

fulfilled

the

error

actual

2.1 Settings

The following settings on the control unit (A1)/control panel of each machine must be

defined and checked:

1. Machine type

LDS (l di h i l d )

LDS

arge s

gna

sen

)

3. Options

4. Delete last error display after elimination

5. Program variants with a given drive potentiometer position

Settings via control panel which

may

be defined by the customer:

Settings

via

control

panel

which

may

defined

the

customer:

a. Display of the last (eliminated) error when turning the machine

ON.

b. Water stage selection when start cleaning

7. Settings on power electronic module

Settings

power

electronic

module

8. DIP-switch for electronic circuit breakers

2.2 Brief Description

The following electronic modules control the machine:

•Control Unit (A1)

•Power Electronic (A2), referred to as ”module 1” in the diagrams

Di C t lU it(A4)

•

(A4)

•Control Panel (A3)

•The control unit (A1) ensures all control and monitoring functions in the machine

except for the drive control unit

except

for

the

drive

control

unit

•There isn’t any error code is displayed on the dash board display, when an error

occurs at the drive control unit since it is equipped with it’s own diagnosis display

(flashing LED at the drive control unit) (see chapter 9).

(flashing

LED

the

drive

control

unit)

(see

chapter

9).

•The keys for scrubbing, vacuuming and the green Minuteman key for combined

cleaning can be used autonomously, only the selected function being active.

2.2.1 Vacuuming OFF/

Soiled Water Tank Full

•The vacuuming function is turned OFF either by operator’s key action or

automatically when the signal “Dirty (Recovery) water tank is full” applies.

•Operator turns vacuuming OFF:

th i lift d

•

e squeegee

lift

•the vacuum motor turned OFF with a delay of 15 seconds

•Turned OFF when tank full:

•

the

“

soiled water tank full

”

switch opens as soon as the tank is filled

•

the

soiled

water

tank

full

switch

opens

soon

the

tank

filled

•If the switch opens 3 seconds or longer (spill protection) the squeegee is lifted and

the suction motor turned off with a delay of 15 seconds.

2.2.2 Initial Position of Machine

•After turning ON the machine, all components are set to “initial position” after the seat

contact switch has closed.

•The lifting elements will lift if they have not been turned OFF in top final position by

the micro switch integrated in the lifting element.

•The motors are turned OFF and the LEDs on the control panel for cleaning elements

extinguish.

•The seat contact switch is connected to the control unit A1 at A1:X7:11+12.

•The A1 control unit’s reaction to activation (opening) of the seat contact switch is

delayed by 2 seconds i.e. if, during operation, the contact is opened for more than 2

seconds, the motors stop and brush head and the squeegee is lifted.

•If the switch is closed again within this delay, operation is not interrupted.

•When the machine is switched ON without the seat switch being closed or when the

switch is opened for more than 2 seconds all functions (driving and cleaning) are now

inhibited.

2.2.2 Initial Position of Machine

•Test the seat contact switch, its wiring and the module’s input by means of the

dia

nosis device: Under code no. 3151 the switch status is dis

(

en or closed

)

gpy(p)

as detected by the module.

•The drive control unit is equipped with an individual diagnosis and self test function.

•Operation of this unit is thus inhibited if the machine is switched ON but the

t ti t i t i NEUTRAL iti it NEUTRAL iti i t d t t d

ome

s no

NEUTRAL

pos

iti

on or

NEUTRAL

pos

iti

s no

•The same applies after the seat contact switch has opened and closed again. The

neutral position of the potentiometer is required as well when actuating the seat

contact switch i e the drive control unit has to detect a neutral position of the

contact

switch

the

drive

control

unit

has

detect

neutral

position

the

potentiometer.

•If the potentiometer position detected by the drive control unit is not neutral, the LED

at the drive control unit flashes. Refer to the chapter on drive control unit test.

the

drive

control

unit

flashes.

Refer

the

chapter

drive

control

unit

test.

Inhaltsverzeichnis

Andere Minuteman Schrubber Handbücher

Minuteman

Minuteman Port A Scrub 14 Bedienungsanleitung

Minuteman

Minuteman E17 Bedienungsanleitung

Minuteman

Minuteman E24 Bedienungsanleitung

Minuteman

Minuteman 260 Series Leitfaden

Minuteman

Minuteman 260 Series Leitfaden

Minuteman

Minuteman Scrubmaster B5 Bedienungsanleitung

Minuteman

Minuteman E17 Bedienungsanleitung

Minuteman

Minuteman ER26 Bedienungsanleitung

Minuteman

Minuteman Port A Scrub 14 Bedienungsanleitung

Minuteman

Minuteman PORT A SCRUB Leitfaden

Minuteman

Minuteman E17 Bedienungsanleitung

Minuteman

Minuteman m12110 Bedienungsanleitung

Minuteman

Minuteman E28 Bedienungsanleitung

Minuteman

Minuteman E26ECO Bedienungsanleitung

Minuteman

Minuteman 620316 Leitfaden

Minuteman

Minuteman 200X Leitfaden

Minuteman

Minuteman MC20115 Leitfaden

Minuteman

Minuteman ERIDE 30 Bedienungsanleitung

Minuteman

Minuteman E20S Bedienungsanleitung

Minuteman

Minuteman ES260 Leitfaden

Minuteman

Minuteman SCV28 Leitfaden

Minuteman

Minuteman SCV 28/32 Leitfaden

Minuteman

Minuteman MC17000QP Leitfaden

Minuteman

Minuteman 380 Leitfaden

Beliebte Schrubber Handbücher anderer Marken

Olympus

Olympus M200H Bedienungsanleitung

Clarke

Clarke BEXT 100H Installations- und Betriebsanleitung

JOHNY VAC

JOHNY VAC JVC70BCT Bedienungsanleitung

RCm

RCm Elan Series Handbuch

Kärcher

Kärcher B 120 W Bedienungsanleitung

Truvox

Truvox Orbis MotorScrubber 20 Bedienungsanleitung

Numatic

Numatic TTB 4045/100 Bedienungsanleitung

U.S. Products

U.S. Products PEX 500-C-TICK Betriebsanleitung

Mclennan

Mclennan C510 Bedienungsanleitung

Tennant

Tennant T20 LPG Bedienungsanleitung

Columbus

Columbus ARA 66 BM 100 Bedienungsanleitung

Numatic

Numatic TTV 678G / 300T Bedienungsanleitung

American-Lincoln

American-Lincoln 505-945 Bedienungsanleitung

FIORENTINI

FIORENTINI ET 65-75 Bedienungsanleitung

Floorpul

Floorpul ruby 48 blt Benutzerhandbuch

Onyx

Onyx RX-34 Bedienungsanleitung

Dustbane

Dustbane Hurricane 400 Bedienungsanleitung

Sana

Sana EUJ-702 Bedienungsanleitung