Minuteman Pro Series Bedienungsanleitung

TABLE OF CONTENTS

Pro Series Owner's Manual

1. Introduction 2

2. Controls and Indicators 4

3. Installation 5

4. Operation 7

5. Troubleshooting 8

6. Replacing the Battery 9

7. Obtaining Service 11

8. Specifications 12

9. Configurable Parameters & Settings 13

10. Limited Product Warranty 14

English

Thank you for purchasing a Minuteman power protection product. It has been designed and

manufactured to provide many years of trouble free service.

Please read the manual before installing your Pro Series UPS as it provides the

information that should be followed during installation and maintenance of the

UPS and batteries allowing you to correctly set up your system for the maxi-

mum safety and performance.

Included is information on customer support and factory service if it is required. If you

experience a problem with the UPS please refer to the Troubleshooting guide in this manual to

correct the problem or collect enough information so that the Minuteman technical support

department can rapidly assist you.

INTRODUCTION

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS !

NOTICE: This equipment has been tested and found to comply with the limits for

a Class B computing device in accordance with the specifications in Subpart J of Part

15 of FCC Rules and the Class B limits for radio noise emissions from digital apparatus

set out in the Radio Interference of the Canadian Department of Communications. These limits are

designed to provide reasonable protection against such interference in a residential installation. This

equipment generates and uses radio frequency and if not installed and used properly, that is, in strict

accordance with the manufacturer's instructions, this equipment may cause interference to radio

and television reception. If this equipment does cause interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

nRe-orient the receiving antenna

nRelocate the computer with respect to the receiver

nMove the computer away from the receiver

nPlug the computer into a different outlet so that the computer and receiver are on different

branch circuits.

nShielded communications interface cables must be used with this product

After removing your Minuteman UPS from its carton, it should be inspected for damage that may

have occurred in shipping. Immediately notify the carrier and place of purchase if any damage is

found. Warranty claims for damage caused by the carrier will not be honored.

Receiving Inspection

WARNING: Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user's authority to operate the equipment.

English

WARNING: RISK OF ELECTRICAL SHOCK. HAZARDOUS LIVE PARTS

INSIDE THIS POWER SUPPLY ARE ENERGIZED FROM THE BATTERY EVEN

WHEN THE AC INPUT POWER IS DISCONNECTED.

TO DE-ENERGIZE THE OUTPUTS OF THE UPS:

1. IF THE UPS IS ON PRESS THE ON/OFF BUTTON FOR 1 SECOND

2. DISCONNECT THE UPS FROM THE AC POWER OUTLET

3. TO DEENERGIZE THE UPS COMPLETELY, DISCONNECT THE BATTERY.

(SEE SECTION 6 FOR INSTRUCTIONS)

CAUTION! TO REDUCE THE RISK OF ELECTRICAL SHOCK IN

CONDITIONS WHERE LOAD EQUIPMENT GROUNDING CANNOT BE VERIFIED,

DISCONNECT THE UPS FROM THE AC POWER OUTLET BEFORE INSTALL-

ING A COMPUTER INTERFACE CABLE. RECONNECT THE POWER CORD

ONLY AFTER ALL SIGNALING CONNECTIONS ARE MADE.

CAUTION! CONNECT THE UPS TO A TWO POLE, THREE WIRE

GROUNDING AC POWER OUTLET. THE RECEPTACLE MUST BE CONNECTED

TO APPROPRIATE BRANCH PROTECTION (CIRCUIT BREAKER OR FUSE).

CONNECTION TO ANY OTHER TYPE OF RECEPTACLE MAY RESULT IN A

SHOCK HAZARD AND VIOLATE LOCAL ELECTRICAL CODES

Para Systems Life Support Policy

As a general policy, Para Systems Inc. (Para Systems) does not recommend the use of any of its

products in life support applications where failure or malfunction of the Para Systems product can

be reasonably expected to cause failure of the life support device or to significantly affect its safety

or effectiveness. Para Systems does not recommend the use of any of its products in direct

patient care. Para Systems will not knowingly sell its products for use in such applications unless

it receives in writing assurances satisfactory to Para Systems that (a) the risks of injury or damage

have been minimized, (b) the customer assumes all such risks, and (c) the liability of Para

Systems Inc. is adequately protected under the circumstances.

Examples of devices considered to be life support devices are neonatal oxygen analyzers, nerve

stimulators (whether used for anesthesia, pain relief, or other purposes), auto transfusion devices,

blood pumps, defibrillators, arrhythmia detectors and alarms, pacemakers, hemodialysis systems,

peritoneal dialysis systems, neonatal ventilator incubators, ventilators for both adults and infants,

anesthesia ventilators, and infusion pumps as well as any other devices designated as critical by

the United States FDA.

Hospital grade wiring devices and leakage current may be ordered as options on many PARA

SYSTEMS UPS systems. PARA SYSTEMS does not claim that units with this modification are

certified or listed as Hospital Grade by PARA SYSTEMS or any other organization. Therefore,

these units do not meet the requirements for use in direct patient care.

The packing materials that your UPS was shipped in are carefully designed to minimize any

shipping damage. In the unlikely case that the UPS needs to be returned to Minuteman, please

use the original packing material. Since Minuteman is not responsible for shipping damage

incurred when the system is returned, the original packing material is inexpensive insurance.

PLEASE SAVE THE PACKING MATERIALS!

English

CONTROLS AND

INDICATORS

Press and release the on/off/test button after one beep to turn the unit on or off

(see section 4)

The online/on battery/boost and buck LED illuminates in a steady state when the

UPS is on and supplying AC power to the load, blinks and sounds the audible

alarm when supplying battery power to the load, blinks with no audible alarm

when the automatic voltage regulator is in operation.

The fault LED illuminates when the UPS has detected an internal fault (contact

Minuteman technical support)

The overload LED illuminates when the loads connected to the Ups exceed the

UPS power rating (see section 4)

The replace battery LED illuminates when the UPS has detected that battery

replacement is required (see section 6)

Pro 1400 front panel

Pro 1400

Pro 200 front panel

fault

Pro 200

on-battery overload replace

battery

online on-battery boost and buck

overload

online

boost

online

FRONT PANEL

boost/buck

on-battery replace

battery

English

INSTALLATION PLACEMENT

Install the UPS in a temperature controlled environment that is free of conductive contaminants.

Select a location which will provide good air circulation for the UPS at all times. Avoid locations

near heating devices, water or excessive humidity, or where the UPS is exposed to direct sunlight.

Route power cords so they cannot be walked on or damaged.

The site wiring fault LED illuminates when the UPS detects an improperly wired AC power outlet

(120 vac MODELS ONLY) see section 3.

The output power receptacles are NEMA 5-15R type. (IEC output sockets on 230 VAC models)

The input power cord has a NEMA 5-15P connector. (IEC input socket on 230 VAC models)

The input circuit breaker will trip in the event the load exceeds the UPSs power rating.

The RJ-45/RJ-11 modular connectors are used for 10 Base-T network/single line telephone surge

protection (see section 3).

The computer interface port is for UPS monitoring and control (see section 3).

REAR PANEL (120 vac models shown)

Pro 1400 rear panel

Pro 200 rear panel

In Out

INSTALLATION

SWF

Interface Port

SWF

Circuit

Breaker

English

CHECKING THE SITE WIRING FAULT (120 VAC models only)

After plugging in the UPS check the site wiring fault (SWF) LED on the rear of the unit. If the LED

is illuminated the UPS is plugged into an improperly wired AC outlet.

CHARGING THE BATTERY

The PRO Series UPSs will charge the internal batteries whenever the unit is connected to an AC

source. It is recommended that the UPS batteries be charged for a minimum of 4 hours before

use. The UPS may be used immediately however the on battery run time may be less than

normally expected.

CAUTION!

IF THE UPS INDICATES A SITE WIRING FAULT, HAVE A QUALIFIED

ELECTRICIAN CORRECT THE PROBLEM.

CONNECTING YOUR EQUIPMENT

Plug the equipment into the receptacles on the rear of the unit. Insure that

you do not exceed the maximum output rating of the UPS (refer to UPS

back panel or electrical specifications in this manual).

CAUTION!

CONNECTING TO AN AC SOURCE

Plug the UPS into a two pole, three wire, grounded receptacle only. Do not use extension cords or

adapter plugs.

CONNECTING TO THE TELEPHONE/NETWORK SURGE PROTECTION

CONNECTION IS OPTIONAL. THE UPS WORKS PROPERLY WITHOUT A

CONNECTION.

NOTE:

NOTE: CONNECTING TO THE COMPUTER INTERFACE PORT IS OPTIONAL. THE UPS

WORKS PROPERLY WITHOUT A CONNECTION.

COMPUTER INTERFACE CONNECTION (OPTIONAL)

Minuteman Power Management software and interface cables kits can be used with the Pro 280

and larger units. Use only Minuteman or Minuteman approved interface cables with these UPSs.

Connect the interface cable to the 9 pin computer interface port on the rear of the UPS. Secure

the connector to the UPS via the screws on the connector housing. Connect the other end of the

cable to the device that will be monitoring/controlling the UPS.

TELEPHONE/NETWORK SURGE PROTECTION CONNECTION (OPTIONAL)

Connect a single line telephone or a 10 Base-T network line to the protection sockets on the rear

of the UPS. This connection will require another length of telephone or network cable. The cable

coming from the telephone service or networked system is connected to the port marked IN, the

OUT port is connected to the equipment to be protected.

DO NOT CONNECT A LASER PRINTER TO THE UPS UNLESS THE UPS IS

RATED 2000VA OR GREATER. A LASER PRINTER DRAWS SIGNIFICANTLY

MORE POWER WHEN PRINTING THAN AT IDLE, AND MAY OVERLOAD THE

UPS.

English

LOW BATTERY WARNING

ALARMS

ON BATTERY

When the UPS is operating on the batteries the on-line LED will blink and the audible alarm will

sound every 10 seconds. The alarm will stop once the UPS returns to on-line operation.

UPS FAULT

When the UPS detects a hardware fault the fault LED will illuminate (the PRO 200 will blink all

LEDs) and the UPS will emit a sustained tone. The fault condition can be re-set by turning the

UPS off and then on (see section 5 for more information).

OVERLOAD

When the amount of load attached to the UPS exceeds its power rating the overload LED will

illuminate and the UPS will emit a sustained tone. This alarm will remain on until the excess load

is removed or the UPSs self protection circuit shuts the UPS down.

REPLACE BATTERY

The UPS automatically tests the batterys condition and will illuminate the replace battery LED and

emit a short beep. This tone will be repeated every hour until the battery passes a self test. It is

recommended that the UPS be allowed to charge overnight before performing a battery test to

confirm a replace battery condition.

The UPS will emit a steady tone when the battery reserve runs low. It continues to emit the steady

tone until AC returns or the UPS shuts down from battery exhaustion.

During the self test the UPS will switch to battery power and the on-line LED will blink and the

audible alarm will sound as well. The length of the test that automatically is performed every two

weeks is longer than the start-up or user invoked test. This test will run for approximately fifteen

seconds to measure the batterys capability to provide an acceptable amount of runtime. If the

UPS fails a self test one of the LEDs will remain illuminated indicating the type of problem. (see

section 5 Troubleshooting)

TURNING THE UNIT ON/OFF

Press and release the switch after one beep to turn the unit on and supply power to the load. The

load are immediately powered while the UPS runs a 5 second self test. Press and release the

switch to turn the unit off. The UPS will continue to charge the batteries whenever it is plugged in

and there is AC present.

SELF TEST

On / Off / Test Switch

On / Off / TestSwitch

The self test feature is useful to verify the correct operation of the UPS and the condition of the

battery. With the UPS plugged into normal AC press and hold the ON/OFF/TEST SWITCH for 4

seconds (four beeps) then release the switch. The UPS will perform a five second self test.

The UPS will automatically perform a self test on startup and every two weeks.Note:

OPERATION

English

Weak or bad batteries/bad battery

connection

Normal operation

UPS will not turn on

All LEDs are flashing

(Pro 200)

Fault LED is

illuminated

The Site Wiring Fault

LED is illuminated

The Online/On battery

LED is illuminated,

but there is no output

Press On button momentarily, (one

beep) to start UPS

On / Off / Test button not

pushed

UPS operates in

battery mode only,

even though there is

normal AC present

Input AC breaker is tripped

UPS has detected an internal

fault

Reset circuit breaker by pressing

the plunger back in. If circuit

breaker trips after UPS starts up,

reduce the load on the UPS

Call for service

Incorrect service wiring Have a qualified electrician correct

the service wiring

Disconnect the computer cable

from the UPS and press the On

button momentarily. If UPS works

normally, software has control of

the UPS

The UPS is being controlled via

its computer port

The batteries may be weak or at

the end of useful service life

Charge the batteries for 8 hours

and retest. If the backup time is

still less than expected, the

batteries may need to be replaced,

even though the replace battery

LED is not illuminated

UPS does not provide

expected backup time

Check the battery connection and/

or replace the batteries. Follow bat-

tery replacement procedures in sec-

tion 6.

The UPS is performing its intended

function

Replace battery LED is

illuminated

The UPS occaisionally

emits a beep

TROUBLESHOOTING

TROUBLESHOOTING CHART

Possible CauseSymptom What To Do

English

REPLACING THE BATTERY

The PRO Series UPS has an easy to replace hot-swappable battery(s). Please read the

following warning statements before attempting to service the battery(s).

REPLACING THE BATTERY

WARNING!

THIS UNINTERRUPTIBLE POWER SOURCE CONTAINS POTENTIALLY

HAZARDOUS VOLTAGES. DO NOT ATTEMPT TO DISASSEMBLE THE UNIT

BEYOND BATTERY REPLACEMENT PROCEDURES BELOW. EXCEPT FOR

THE BATTERY, THIS UPS CONTAINS NO USER SERVICABLE PARTS.

REPAIRS CAN BE PERFORMED BY MINUTEMAN SERVICE PERSONNEL

ONLY

DO NOT OPEN OR MUTILATE BATTERIES. RELEASED ELECTROLYTE

IS HARMFUL TO THE SKIN AND EYES AND MAY BE TOXIC

CAUTION:

CAUTION: DO NOT DISPOSE OF BATTERIES IN A FIRE. THE BATTERIES MAY EX-

PLODE.

THE BATTERIES IN THIS UPS ARE RECYCLABLE. DISPOSE OF THE

BATTERIES PROPERLY. THE BATTERIES CONTAIN LEAD AND POSE A

HAZARD TO THE ENVIRONMENT AND HUMAN HEALTH IF NOT DISPOSED

OF PROPERLY. REFER TO LOCAL CODES FOR PROPER DISPOSAL

REQUIREMENTS OR RETURN THE BATTERY TO MINUTEMAN.

ALTHOUGH BATTERY SYSTEM VOLTAGES ARE ONLY 12 VDC AND 24

VDC THE BATTERY SYSTEM CAN STILL PRESENT A RISK. THE

CURRENT CAPABILITY OF A BATTERY IS SUFFICENT TO BURN WIRE

OR TOOLS VERY RAPIDLY, PRODUCING MOLTEN METAL. OBSERVE

THESE PRECAUTIONS WHEN REPLACING THE BATTERIES:

1. REMOVE WATCHES, RINGS, OR OTHER METAL OBJECTS;

2. USE HAND TOOLS WITH INSULATED HANDLES;

3. DO NOT LAY TOOLS OR OTHER METAL PARTS ON TOP OF

BATTERIES

REPLACE BATTERIES WITH THE SAME NUMBER AND TYPE AS

ORIGINALLY INSTALLED IN THE UPS. THESE BATTERIES HAVE

PRESSURE OPERATED VENTS.

CAUTION:

English

4. Connect the new battery in place of the old one, ensuring that black wire is connected to the

negative (-) terminal and the red wire is connected to the positive (+) terminal. ( the Pro 1400

connectors are keyed) Small sparks at the battery connection are normal.

5. Place the new battery in the case taking care not to pinch any wires.

6. Slide the battery door back into its slot and replace the retaining screw.

7. Dispose of the battery properly at an appropriate recycling facility or return it to the supplier in

the packing material for the new battery. See new battery instructions for more info.

BATTERY REPLACEMENT PROCEDURE

PLEASE READ THE CAUTIONS SECTION BEFORE ATTMPTING TO REPLACE

THE BATTERIES

1. Lay the unit on its side or bring to the edge of a table.

Remove the retaining screw holding the

battery door in place and slide the door towards the

bottom of the unit.

2. Gently pull out the battery by grasping the battery removal tab

3. Disconnect the two wires (disconnect the connector on the 1400 va unit) connecting the battery

to the UPS. Pull back straight on the connector while wiggling the connector from side to side.

Pro 1400

pull

connect

replace

pull

open

disconnect

connect

disconnect

connect

replace

English

Andere Handbücher für Pro Series

Andere Minuteman UPS Handbücher

Minuteman

Minuteman MM-AVR Bedienungsanleitung

Minuteman

Minuteman EN750LCD Bedienungsanleitung

Minuteman

Minuteman ED6000RMXFMR Bedienungsanleitung

Minuteman

Minuteman Encompass Series Bedienungsanleitung

Minuteman

Minuteman MBK-E SERIES Bedienungsanleitung

Minuteman

Minuteman Enspire Series Bedienungsanleitung

Minuteman

Minuteman Endeavor ED1000RTXL2U Bedienungsanleitung

Minuteman

Minuteman Pro Series Bedienungsanleitung

Minuteman

Minuteman E1000RM1U Bedienungsanleitung

Minuteman

Minuteman PRO-E Bedienungsanleitung

Minuteman

Minuteman MN 325/MN 525 Bedienungsanleitung

Minuteman

Minuteman ETR550LCD Bedienungsanleitung

Minuteman

Minuteman Entrust-LG Series Bedienungsanleitung

Minuteman

Minuteman 6-10KVA Tower Bedienungsanleitung

Minuteman

Minuteman Entrepid Series Bedienungsanleitung

Minuteman

Minuteman MCP-E Bedienungsanleitung

Minuteman

Minuteman Enterprise Series Bedienungsanleitung

Minuteman

Minuteman EN750 Bedienungsanleitung

Minuteman

Minuteman CPE 1000 On-Line Series Gebrauchsanweisung

Minuteman

Minuteman Pro 2200r Bedienungsanleitung

Minuteman

Minuteman MBK-E SERIES Bedienungsanleitung

Minuteman

Minuteman PRO1100E Bedienungsanleitung

Minuteman

Minuteman 1000 VA Bedienungsanleitung

Minuteman

Minuteman Enterprise Plus LCD RTXL UPS Series Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung