MiTEC MKP-1101 Bedienungsanleitung
MKP-1101
How to, quickly, setup the keypad for use by up to 20 users.
1. The master code is used to access programming mode. (Default master code = 1234)
The amount of digits used in the master code can be anything between 4 and 8 digits.
NB! The number of digits used for the master code will determine the length of all other codes.
I.e. The default master code is 1234 so therefore all user codes will be 4 digits long.
Setup a new master code: (Default = 1234)
Current Master Code Current Master Code (chime tone up) *00 New 4 to 8 digit Master Code # (chime
tone down)
I.e. To change the master code to 4321:- 1234 1234 *00 4321 #
Setup user codes 01 to 19 that activate the lock relay: (User 01 default = 3333)
Type in the following:
Master Code Master Code (chime tone up) *two digit user number New User Code (chime tone up)
I.e. To change user 01 to 8282 without exiting program mode afterwards: -
1234 1234 *01 8282
Repeat for additional users or type # to exit programming mode (Chime tone down).
Type in the following:
Deleting a user code:
Type in the following:
Master Code Master Code (chime tone up) *00 # to clear all users and default user 01 to 3333
Or
Master Code Master Code (chime tone up) * 2 digit user number # to clear an individual user.
Setup type or pulse length of Lock relay: (Default = 5 sec.)
Type in the following:
Master Code Master Code (chime tone up) *20 00 for latch mode or 01 sec for 1 sec, 02 for 2
sec 99 for 99 sec # to exit programming mode. (Chime tone down)
1
Setup code to activate the Auxiliary relay: (Default none)
Type in the following:
Master Code Master Code (chime tone up) *40 New Auxiliary Code (chime tone up)
I.e. To setup Aux relay code to 2222 without exiting program mode afterwards:-
1234 1234 *40 2222
Continue to additional programming or type # to exit programming mode (Chime tone down).
4
Enter programming mode
Change master code
Set user codes 01 ~ 19 (Lock output relay
only)
Set user codes 20 ~ 39 and 41 ~ 99 (lock
output relay only)
Set user code 40 (Aux output only)
Select Lock relay mode or pulse length.
Activating incorrect code input lockout (20
digits or 5 attempts results 30sec lockout)
Delete a user code or all user codes. (If
deleting all user 01 defaults to 3333)
Activating bypass mode.
De-activate bypass mode.
Setup bypass code
Disable alarm output mode
Select alarm output activates on door forced
open condition
Select alarm output activates on tamper
switch
Select alarm output activates on both door
forced and tamper switch
Select Alarm output active time
Select Aux ouput mode or pulse length
Disable Aux ouput
Allocate door monitor to work with Aux
output
Activate Aux output when incorrect code is
entered
Activate Aux output when * key is pressed
(Doorbell function)
Activate Aux output when tamper is activated
Activate Aux output when door is forced open
Activate Aux out at same as lock output
Aux ouput only activates when Aux code is
entered
Factory default
Place jumper across restore pins
Power up
On continuous chime remove jumper and replace it in normal operation position.
Need Action Response
Buzzer LED
Master code - Master code
*00 - new master code (4-8 digits) Note the number of digits the master
is set to will be the number of digits each user code must be.
*01~ 19 - new unique user code (Same length as master code)
*6 - 2 digit user number - new unique user code (Same length as master code)
*40 new unique aux user code (Same length as master code)
*20 - 00 = latch mode or 01 sec for 1 sec, 02 for 2 sec 99 for 99 sec
*51
*50 - 00 for all, 01 for user 1, 02 for user 2 .99 for user 99.
*52 - 1
*52 - 0
*54 - new unique bypass code
*55 - 0
*55 - 1
*55 - 2
*55 - 3
*56 - 001 for 1 sec, 002 for 2 sec ..999 for 999 sec.
*58 - 00 = latch mode or 001 for 1 sec, 002 for 2 sec ..999 for 999 sec.
*57 - 0
*57 - 1
*57 - 2
*57 - 3
*57 - 4
*57 - 5
*57 - 6
*57 - 7
Yellow
Chime tone
up
No chime
tone
Chime tone
up
Chime tone
up
Chime tone
up
Chime tone
up
Chime tone
up
Chime tone
up
Chime tone
up
Chime tone
up
Chime tone
up
Chime tone
up
Chime tone
up
Chime tone
up
Chime tone
up
Chime tone
up
Chime tone
up
Chime tone
up
Chime tone
up
Chime tone
up
Chime tone
up
Chime tone
up
Chime tone
up
Chime tone
up
Continuous
chime
Yellow
Yellow
Power down
ADVANCED PROGRAMMING OPTIONS.
3
Setup type or pulse length of Auxiliary relay: (Default = latch mode)
Type in the following:
Master Code Master Code (chime tone up) *58 00 for latch mode or 001 sec for 1 sec, 002 for 2
sec 999 for 99 sec # to exit programming mode. (Chime tone down)
Activate the incorrect code attempt lock out: (Default = disabled)
(Keypad disables keystrokes for 30 sec. after 5 incorrect code entries or 20 consecutive incorrect
keystrokes.
Type in the following:
Master Code Master Code (chime tone up) *51 # to exit programming mode. (Chime tone down)
Activate the Bypass code option: (Default = Deactivated)
(When the Bypass code is entered the Lock relay latches on until the bypass code is re-entered)
Type in the following:
Master Code Master Code (chime tone up) *52 1 # to exit programming mode. (Chime tone down)
Deactivating the bypass mode option:
Type in the following:
Master code Master code (chime tone up) *52 0 # to exit programming mode. (Chime tone down)
Setup bypass code: (Default = none)
(When the Bypass code is entered the Lock relay latches on until the bypass code is re-entered)
Type in the following:
Master Code Master Code (chime tone up) *54 New unique bypass code # to exit programming
mode. (Chime tone down)
Power down.
Place jumper in the system restore position.
Power up.
Replace jumper in the original position at sound of buzzer tone.
All settings and codes are now back at factory default value.
Default the Keypad to factory default settings:
2
12V/24V
Aux Out
Nc
Com
No
Lock Out
(-)
Out
AL
POWER
SUPPLY
1N4004
DOOR RELEASE
BUTTON
NEGATIVE TRIGGER
STROBE / ALARM
DEVICE
+
STRIKE
MAG
+
-
CATHODE
ELECTRIC LOCK
DC
AC/DC
12v-24v
Andere MiTEC Tastenfeld Handbücher
