Mitel Mediatrix Model M Handbuch

GX Gateway

Hardware Installation Guide

March 23, 2020

Notice

The information contained in this document is believed to be accurate in all respects but is not warranted by Mitel Networks™

Corporation (MITEL®). The information is subject to change without notice and should not be construed in any way as a commitment

by Mitel or any of its affiliates or subsidiaries. Mitel and its affiliates and subsidiaries assume no responsibility for any errors

or omissions in this document. Revisions of this document or new editions of it may be issued to incorporate such changes. No

part of this document can be reproduced or transmitted in any form or by any means - electronic or mechanical - for any purpose

without written permission from Mitel Networks Corporation.

Trademarks

The trademarks, service marks, logos and graphics (collectively “Trademarks”) appearing on Mitel's Internet sites or in its publications

are registered and unregistered trademarks of Mitel Networks Corporation (MNC) or its subsidiaries (collectively "Mitel")

or others. Use of the Trademarks is prohibited without the express consent from Mitel. Please contact our legal department at

legal@mitel.com for additional information. For a list of the worldwide Mitel Networks Corporation registered trademarks, please

refer to the website: http://www.mitel.com/trademarks.

®,™ Trademark of Mitel Networks Corporation

DGW 45.3.19712020-02-19

Table ofContents

Table of Contents

SafetyRecommendationsand Information....................................................................................................................................5

Danger, Warning, Caution, and Note Definitions........................................................................................................................5

Electrical Safety Guidelines.........................................................................................................................................................5

General Safety Practices.............................................................................................................................................................7

Electrostatic Discharge Prevention .............................................................................................................................................8

Translated Warning Definition.....................................................................................................................................................8

Requirements .............................................................................................................................................................................10

Location Requirements..............................................................................................................................................................10

Wiring Guidelines ......................................................................................................................................................................11

Mitel GX Gateway Characteristics.............................................................................................................................................11

Getting Started ...........................................................................................................................................................................12

Installation Check List................................................................................................................................................................12

Package Check List...................................................................................................................................................................13

Cleaning Instructions.................................................................................................................................................................13

Mounting Tools andEquipment..................................................................................................................................................13

Connectors and Indicators ........................................................................................................................................................14

Installing the Mitel GX Gateway .................................................................................................................................................18

Installing the Unit on a Flat Surface ..........................................................................................................................................19

Connecting the Telephony Cables............................................................................................................................................19

Connecting the Mitel GX Gateway Using a DHCP Server........................................................................................................20

Connecting the Mitel GX Gateway Using a Static IP Address..................................................................................................21

Verifyng the Installation.............................................................................................................................................................22

Cables.........................................................................................................................................................................................23

Gigabit Ethernet Connection(RJ-45).........................................................................................................................................23

PRI Connection (RJ-48) ............................................................................................................................................................24

FXS and FXO Connections (RJ-11)..........................................................................................................................................25

Table ofContents

Troubleshooting..........................................................................................................................................................................26

Locating the Product Serial Number .........................................................................................................................................26

Troubleshooting.........................................................................................................................................................................27

LED Patterns.............................................................................................................................................................................27

RESET/DEFAULT Button..........................................................................................................................................................28

Partial Reset..............................................................................................................................................................................29

Performing a Partial Reset...................................................................................................................................................31

Disabling the Rescue Interface ............................................................................................................................................31

Factory Reset ............................................................................................................................................................................32

Performing a Factory Reset .................................................................................................................................................32

Standards Compliance and Disclaimers ....................................................................................................................................33

Supported Standards.................................................................................................................................................................33

Federal Communications Commission (FCC) Disclaimer.........................................................................................................34

Innovation, Science and Economic Development Canada (ISED) Disclaimer .........................................................................35

CE Marking................................................................................................................................................................................35

RoHS China...............................................................................................................................................................................35

Other Disclaimers......................................................................................................................................................................36

FXOCard-StandardsofComplianceand

Disclaimers .....................................................................................................................37

FXO Card - Supported Standards.............................................................................................................................................37

FXO Card -FederalCommunications Commission(FCC)Disclaimer .........................................................................................37

FXOCard-Innovation,ScienceandEconomicDevelopmentCanada

(ISED)Disclaimer...................................................................38

PRI/T1/E1/J1Card -StandardsComplianceand

Disclaimers...........................................................................................................39

PRI/T1/E1/J1 - Card Supported Standards...............................................................................................................................39

PRI/T1/E1/J1Card-FederalCommunicationsCommission(FCC)

Disclaimer..................................................................................39

PRI/T1/E1/J1Card-Innovation,ScienceandEconomicDevelopment

Canada (ISED)Disclaimer ....................................................40

Product DisposalInstructions......................................................................................................................................................40

GX Gateway Hardware Installation Guide 5

SafetyRecommendationsand Information

Danger, Warning, Caution, and Note Definitions

Danger

: Indicates a hazardous situation which, if not avoided, will result in death or serious

injury.

Warning: Indicates a hazardous situation which, if not avoided, could result in death or serious

injury.

Caution: Indicatesahazardoussituationwhich,ifnotavoided,couldresultinminoror moderate

injuryordamagetoproperty orequipment.

Note: Indicates important information not related to personal injury.

Electrical Safety Guidelines

Danger:

Do not work on the Mitel GX Gateway, connect or disconnect its cables during periods

of lightning.

Danger: Avoid using a telephone (other than a cordless type) during an electrical storm. There

may be a remote risk of electric shock from lightning.

Warning:

The earth ground cable must be firmly and securely connected to the grounding screw

on the back of the Mitel GX Gateway and an appropriate grounding point in your site: the earth

ground cable must remain tightly secured at all times during service and installation.

Warning:

Disconnect all interface cables (including PRI, FXS, and FXO) before unplugging any

power sources from the Mitel GX Gateway.

Warning:

Disconnect all interface cables (including PRI, FXS, and FXO) as well as all power

sources connected to the Mitel GX Gateway before servicing the unit.

Warning:

This equipment must be installed and maintained by service personnel. Incorrectly

connecting this equipment to a general-purpose outlet could be hazardous.

GX Gateway Hardware Installation Guide 6

Warning:

This product relies on the building's installation for short-circuit (overcurrent) protection.

Ensure that a fuse or circuit breaker no larger than 120 VAC, 15 A U.S. (240 VAC, 10 A

international) is used on the phase conductors (all current-carrying conductors).

Warning: The unit must be grounded at all times when in use.

Warning:The earth ground connection between the grounding screw on the back of the Mitel GX

Gateway and an appropriate grounding point in your site must always be made first and

disconnected last.

Warning: Do not connect the ETH2, ETH1, LAN, and FXS connectors directly to the Public

Switched Telephone Network (PSTN), to an off premise application, an out of plant application,

any exposed plant application, or to any equipment other than the intended application,

connection may result in a safety hazard, and/or defective operation and/or equipment damage.

Exposed plant means where any portion of the circuit is subject to accidental contact with electric

lighting or power conductors operating at a voltage exceeding 300 V between conductors or is

subject to lightning strikes.

Warning:The Mitel GX Gateway must be installed on a circuit equipped with a breaker so that

you can easily power the unit off if required.

Warning: Hazardous network voltages may be present in PRI and FXO cables. Always

disconnect the cables from the Mitel GX Gateway first to avoid possible electric shock. Network

hazardous voltages may be present on the device in the area of the PRI and FXO port, even when

power is turned OFF.

Warning:

Adequate earth ground connection of the Mitel GX Gateway is mandatory to avoid any

damage or injuries.

Warning:

Hazardous network voltages might be present in WAN, LAN, Sync, and telephony port

connectors regardless of whether power to the device is OFF or ON. Use caution when working

near these connectors to avoid electric shocks.

Warning:

The socket outlet, if used, shall be located near the equipment and shall be easily

accessible by the user. The AC adaptor inlet is considered as a disconnection device. The device

must be readily operational.

Caution: To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cords.

Caution: The RJ-11 cable should comply with UL 1863 and CSA C22.2 No 233 standards.

GX Gateway Hardware Installation Guide 7

General Safety Practices

Warning: Do not use this product near water, for example, near a bath tub, wash bowl, kitchen

sink or laundry tub, in a wet basement or near a swimming pool.

Warning:

Do not expose the unit to rain or moisture to avoid any shock hazard.

Warning:

Do not use the telephone to report a gas leak in the vicinity of the leak.

Warning: Do not get this product wet or pour liquids into it.

Warning:

Ultimate disposal of this product should be handled according to all national laws and

regulations.

Caution:

If the unit is installed in a closed environment or on a multi-unit rack, the ambient

temperature of the environment next to the Mitel unit may become greater than the maximum

operating temperature recommended by Mitel for the use of its units, i.e. 40ºC. The Mitel GX

Gateway should never be used to temperatures greater than the recommended maximum

operating temperature. Any damage occurring in such environmental conditions will void the

warranty.

•

Keep your Mitel GX Gateway clear and dust-free during and after installation.

•

Locate the emergency power-off switch for the room in which you are working. Then, if an

electrical accident occurs, you can act quickly to turn off the power.

•

Do not work alone if potentially hazardous conditions exist.

•

Never assume that power is disconnected from a circuit. Always check.

•

Do not perform any action that creates a potential hazard to people or makes the equipment

unsafe.

•

Do not open or disassemble this product.

•

The unit should be located at 20 cm from your monitor, computer casing or other peripheral

including speakers.

•

When the unit is brought from a cold to a warm environment, condensation, that might be

harmful to the unit, may occur. If this is the case, wait one hour before powering the unit.

GX Gateway Hardware Installation Guide 8

Electrostatic Discharge Prevention

•

When working on a Mitel GX Gateway, always wear an ESD wrist strap, ensuring that it makes a good contact

with your bare skin.

•

Attach the ESD wrist strap end to an earth ground i.e. the grounding screw on the back of the Mitel GX

Gateway or on an unpainted bare metal spot of a grounded equipment rack.

Translated Warning Definition

Warning: Means danger. You are in a situation that could cause bodily injury. Before you work

on any equipment, you must be aware of the hazards involved with electrical circuitry and familiar

with standard practices for preventing accidents.

Attentie: Dit waarschuwingssymbool betekent gevaar. U overtreat in een situatie die lichamelijk

letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn

van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van standaard

maatregelen om ongelukken te voorkomen.

Varoitus: Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa

ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää

sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista.

Averrtissement:

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une

situation pouvant causer des blessures ou des dommages corporels. Avant de travailler sur un

équipement, soyez conscient des dangers posés par les circuits électriques et familiarisez-vous

avec les procédures couramment utilisées pour éviter les accidents.

Warnung:

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu einer

Körperverletzung führen könnte. Bevor Sie mit der Arbeit an irgendeinem Gerät beginnen, seien

Sie sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur

Vermeidung von Unfällen bewußt.

Avvertenza: Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare

infortuni alle persone. Prima di lavorare su qualsiasi apparecchiatura, occorre conoscere i pericoli

relativi ai circuiti elettrici ed essere al corrente delle pratiche standard per la prevenzione di

incidenti.

GX Gateway Hardware Installation Guide 9

Advarsel:

Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan føre til

personskade. Før du utfører arbeid på utstyr, må du vare oppmerksom på de faremomentene

som elektriske kretser innebærer, samt gjøre deg kjent med vanlig praksis når det gjelder å unngå

ulykker.

Aviso: Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá causar

danos físicos. Antes de começar a trabalhar com qualquer equipamento, familiarize- se com os

perigos relacionados com circuitos eléctricos, e com quaisquer práticas comuns que possam

prevenir possíveis acidentes.

Aviso:

Este símbolo de aviso significa peligro. Existe riesgo para su integridad física. Antes de

manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y

familiarizarse con los procedimientos estándar de prevención de accidentes.

Varning - risk för maskinskada:

Denna varningssymbol signalerar fara. Du befinner dig i en

situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara

medveten om farorna med elkretsar och känna till vanligt förfarande för att förebygga skador.

GX Gateway Hardware Installation Guide 10

Requirements

Location Requirements

Toavoidprematureagingoftheunit,ensureusersecurityandfacilitateaccess,upgradesand maintenance,the

followingguidelinesmustbefollowed.

•

Install the Mitel GXGateway:

•

onastandard48.26cm(19 in.)equipment rack

•

ona flat surface (desk,table,etc.)

•

InstalltheMitel GX Gatewayinawell-ventilatedlocationwhereitwillnotbeexposedtohigh

temperatures orhumidity.

•

Storagetemperature: -

•

ºCto+70ºC

•

Operatingtemperature:0ºC to +40ºC

Caution: If the unit is installed in a closed environment or on a multi-unit rack, the ambient

temperature of the environment next to the Mitel unit may become greater than the

maximum operating temperature recommended by Mitel for the use of its units, i.e. 40ºC.

The Mitel GX Gateway should never be used to temperatures greater than the

recommended maximum operating temperature. Any damage occurring in such

environmental conditions will void the warranty.

•

Humidity lower than 85% and non-condensing

•

Do not install the Mitel GX Gateway in a location exposed to direct sunlight or near stoves or

radiators. Excessive heat could damage the internal components.

•

Unit should be positioned to be accessible for future upgrade, maintenance and

troubleshooting and where cables can be easily connected.

•

Maintain a minimum of 25 mm (1 in.) clearance in front, in the back, on top, under (for rack

mounted units), and on the sides of the unit.

•

Keep airflow around and through the vents of the unit clear of any obstruction.

•

Do not put books or paper on the unit.

Inhaltsverzeichnis

Andere Mitel Tor Handbücher

Mitel

Mitel MiVOICE BUSINESS Bedienungsanleitung

Mitel

Mitel 3300 Bedienerhandbuch

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung