Mitel 2000 Series Handbuch

Mobility Router 2000 Series

Hardware Installation Guide

October 25, 2017

Legal Notices

2 Mobility Router 2000 Series Hardware Installation Guide Mobility

Trademarks

Any reference to third-party trademarks is for reference only and Mitel makes no representation of ownership of these marks.

Patents

Mobility Router 2000 is covered by patents as listed at http://www.shoretel.com/about/patents.html.

Version Information

Mobility Router 2000 Series Hardware Installation Guide

Date: September 2017

related Mobility Router documentation.

Mobility Router 2000 Installation

Specifications

2 Mobility Router 2000 Series Hardware Installation Guide

1.2 Specifications

The Mobility Router is one rack unit(RU) high and installed in a standard 19-inch (48.26-cm) rack.

Figure 1-1. Front View of RoamAnywhere Mobility Router 2000 Series

Figure 1-2. Rear View of RoamAnywhere Mobility Router 2000 Series

Table 1-1 Mobility Router Connection Specifications

Table 1-2 Mobility Router Power Specifications

Table 1-3 Mobility Router Physical Specifications

Table 1-4 Mobility Router Operating Environment

Mobility Router 2000

Model Port Connection

Mobility Router 2000 Series Ethernet

Console

1 ea. ETH0

1 ea. ETH1

Serial

Model Power Supply

Mobility Router 2000 Series 100-240 VAC (auto-range), 200 W, 3A,50-60 Hz

Model Dimensions (WxHxD)Weight

Mobility Router 2000 Series 16.8 x 1.7 x 14 inches

(427 x 43x 356 mm) 17.7 lb (7.7 kg)

Model Temperature Humidity

Mobility Router 2000 Series Operating: 10 to 35 C

(50 to 95 F)

Non-operating: -40 to 70 C

(-40 to 158 F)

Operating: 8% to 90%

(non-condensing)

Non-operating: 5 to 95%

(non-condensing)

Mobility Router 2000 Series Hardware Installation Guide 3

Mobility Router 2000 Installation

Specifications 1

Table 1-5 Status LEDs

Regulatory compliance:

Electromagnetic Emissions: FCC Class A, EN 55022 Class A,EN 61000-3-2/-3-3, CISPR 22 Class A

Electromagnetic Immunity: EN55024/CISPR24,(EN61000-4-2,EN61000-4-3,EN61000-4-4,

EN 61000-4-5, EN 61000-4-6, EN 61000-4-8, EN 61000-4-11)

Safety: CSA/EN/IEC/UL 60950-1 Compliant,UL or CSA Listed (USAand Canada), CE Marking (Europe)

LED Appearance Meaning

Power On continuously Indicates that power is supplied to power supply unit.

Hard drive activity Blinking yellow Indicates hard drive activity.

LAN activity (eth1) Blinking Indicates network activity on the eth1 port.

LAN activity (eth0) Blinking Indicates network activity on the eth0 port.

Overheating/fan failure Blinking Indicates fan failure.

On continuously Indicates that the Mobility Router is overheated.

Mobility Router 2000 Installation

Unpacking a Mobility Router

4 Mobility Router 2000 Series Hardware Installation Guide

1.3 Unpacking a Mobility Router

The carton for a Mobility Router contains the following:

OneMobility Router withrackmount ears

End-user license agreement (EULA)

One power cord

One serial cable for serial console connection

Onestraight-through Ethernetcable

A copy of this document

Before starting the installation:

1Open the carton and remove the contents.

2If any contents are missing or damaged, contact Technical Support at +1.408.331.3300 or

http://support.shoretel.com.

3Keep the packing materials and save the carton.

Mobility Router 2000 Series Hardware Installation Guide 5

Mobility Router 2000 Installation

Installation Requirements and Recommendations 1

1.4 Installation Requirements and

Recommendations

Before installing a Mobility Router,follow these requirements and recommendations.

1.4.1 Installation Location Guidelines

The MobilityRouter should beinstalled in an environment sufficientfor normal operation of network appliances

(50-95°F). Make sure that the area allows for enough ventilation after the Mobility Routerisinstalled. The

appliance should be installed in an area that does not exceed the following humidity range: 8-90%

non-condensing.

1.4.2 Rack Requirements

The Mobility Router must be installed in a standard 19-inch rack. Make sure that the Mobility Router is installed in

the rack so that the Mobility Router is level in the rack and is fastened by screws on both sides. Refer to “Installing

the Mobility Router” on page 6 for installation instructions

1.4.3 Required Equipment for Installation

The following equipment is required for rack installation (and depends on the type of rack):

Mounting screws to rack mount the Mobility Router (not provided)

Screwdriver (not provided)

1.4.4 Uninterruptible Power Supply

We recommend installing the Mobility Router inan existing Uninterruptible Power Supply (UPS) infrastructure.

Mobility Router 2000 Installation

Installing the Mobility Router

6 Mobility Router 2000 Series Hardware Installation Guide

1.5 Installing the Mobility Router

Required Tools:

4each“cage” typemounting nuts (not included)

4 each Pan Head screws, typically 10-32 thread size (not included)

To connect the Mobility Router to the rack:

1Snap the mounting nuts into the rack at the desired mounting point.

Figure 1-3. Insert Mounting Nuts into Rack

2Lift the Mobility Router to the desired rack position.

3Install each Pan Head screw through the Mobility Router’s mounting ears into the mounting nuts.

Figure 1-4. Fastening the Mobility Router to the Rack

4Tighten to 30 inch-lbs. Do not over-tighten.

tbd screws being inserted (with arrows) into ears

Mobility Router 2000 Series Hardware Installation Guide 7

Mobility Router 2000 Installation

Connecting to the Network 1

1.6 Connecting to the Network

Connect the Mobility Router to a network device, such as a switch, using the straight-through Ethernet cable

provided with the Mobility Router.

To connect the Mobility Router to the network:

1Insert one end of the Ethernet cableto the network device.

2Insert the other end of the Ethernet cable to the left Ethernet port (ETH0) on the rear of the Mobility Router.

NOTE If using the Secure Remote Voice feature, connect the second Ethernet port (ETH1)to the external

network.

Figure 1-5. Connecting the Ethernet Cable to the Mobility Router

Mobility Router 2000 Installation

Connecting to the Console Port

8 Mobility Router 2000 Series Hardware Installation Guide

1.7 Connecting to the Console Port

The Mobility Router uses a serial console port to provide a direct connection to the command-line interface (CLI)

Wizard for initial configuration the Mobility Router. After completing the initial configuration, access to the

console port is no longer necessary.

To initially configure the Mobility Router, connect the management PC or laptop to the serial console port of the

Mobility Router. If there is no serial port, use a 9-pin serial to USB adapter to connect to the serial cable.

To connect the PC or laptop tothe serial console port:

1Insert one end of the serial cable into the PC or laptop serial port.

2Insert the other end of the cable into the serial console port of the Mobility Router.

Figure 1-6. Connecting to the Serial Console Port

3On the PC or laptop,start terminal emulation software (such as Microsoft HyperTerminal) and select the

appropriate COM port.

4Configure the port using the following settings:

Baud rate: 9600 bps

Data bits: 8

Parity:None

Stop bits: 1

Flow control: None

Inhaltsverzeichnis

Andere Mitel Netzwerk-Router Handbücher

Mitel

Mitel 4000 Series Handbuch

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung