Mitsubishi Electric MSZ-FH12NA Bedienungsanleitung

CONTENTS

1. TECHNICAL CHANGES ··································· 3

2. PART NAMES AND FUNCTIONS····················· 4

3. SPECIFICATION················································ 5

4. OUTLINES AND DIMENSIONS ························ 6

5. WIRING DIAGRAM············································ 7

6. REFRIGERANT SYSTEM DIAGRAM··············· 8

7. SERVICE FUNCTIONS ····································· 9

8. MICROPROCESSOR CONTROL ····················11

9. TROUBLESHOOTING····································· 20

10. DISASSEMBLY INSTRUCTIONS···················· 32

INDOOR UNIT

SERVICE MANUAL

INDOOR UNIT

Models

MSZ-FH06NA

MSZ-FH09NA

MSZ-FH12NA

MSZ-FH15NA

MSZ-FH18NA

MSZ-FH18NA2

NOTE:

RoHS compliant products have <G> mark on the spec name plate.

No. OBH683

REVISED EDITION-D

Please void OBH683 REVISED EDITION-C.

Revision D:

• MSZ-FH06NA and MSZ-FH18NA2 have been

added.

PARTS CATALOG (OBB683)

Outdoor unit service manual

MUZ-FH·NA(H) Series (OBH684)

MXZ-C•NA,NAHZ Series (OCH573)

Use the speciﬁed refrigerant only

Never use any refrigerant other than that specified.

Doing so may cause a burst, an explosion, or fire when the unit is being used, serviced, or disposed of.

Correct refrigerant is specified in the manuals and on the spec labels provided with our products.

We will not be held responsible for mechanical failure, system malfunction, unit breakdown or accidents caused by

failure to follow the instructions.

Revision A:

• 3. SPECIFICATION has been modified.

(The value of the disconnect switch for MSZ-FH15NA has been modified.)

• 8. MICROPROCESSOR CONTROL has been modified.

• 9. TROUBLESHOOTING has been modified.

Revision B:

• 4. OUTLINE AND DIMENSIONS has been modified.

(The length of the connect pipes has been modified.)

• Some descriptions have been modified.

Revision C:

• MSZ-FH18NA has been added.

Revision D:

• MSZ-FH06NA and MSZ-FH18NA2 have been added.

OBH683D

TECHNICAL CHANGES

MSZ-FH09NA

MSZ-FH12NA

MSZ-FH15NA

1. New model

MSZ-FH18NA

1. New model

MSZ-FH06NA

MSZ-FH18NA2

1. New model

OBH683D

ACCESSORIES

MSZ-FH06NA MSZ-FH09NA MSZ-FH12NA MSZ-FH15NA MSZ-FH18NA MSZ-FH18NA2

PART NAMES AND FUNCTIONS

Model

MSZ-FH06NA

MSZ-FH09NA

MSZ-FH12NA

MSZ-FH15NA

MSZ-FH18NA

MSZ-FH18NA2

Installation plate 1

Attachment screws for the installation

plate 4 × 25 mm 5

Remote controller holder 1

Screw for the remote controller holder

3.5 × 16 mm (Black) 2

Battery (AAA) for the remote controller 2

Wireless remote controller 1

Felt tape (For left or left-rear piping) 1

Air cleaning ﬁlter

(Electrostatic anti-allergy enzyme ﬁlter) 1

Air cleaning ﬁlter (Deodorizing ﬁlter) 1

Operation indicator lamp Remote control receiving

section

Emergency

operation

switch

Horizontal

vane

Air inlet

Air ﬁlter

(Nano platinum ﬁlter)

Air cleaning ﬁlter

(Electrostatic anti-allergy

enzyme ﬁlter and deodorizing ﬁter)

Front panel

Air outlet

i-see SENSOR

Remote controller

OBH683D

SPECIFICATION

3-2. OUTLET AIR SPEED AND COVERAGE

●The air coverage is the figure up to the

position where the air speed is 1 ft./s,

when air is blown out horizontally from

the unit properly at the High speed

position.

The coverage should be used only

as a general guideline since it varies

according to the size of the room and

furniture arranged inside the room.

(2) OPERATION

Mode Condition

Intake air temperature (°F)

Indoor Outdoor

DB WB DB WB

Cooling

Standard temperature 80 67 95 —

Maximum temperature 90 73 115 —

Minimum temperature 67 57 14 —

Maximum humidity 78% —

Heating

Standard temperature 70 60 47 43

Maximum temperature 80 67 75 65

Minimum temperature 70 60 -13 -14

3-1. OPERATING RANGE

(1) POWER SUPPLY

Rated voltage Guaranteed voltage (V)

Indoor unit

208/230 V

1 phase

60 Hz

Min. 187 208 230 Max. 253

Indoor unit model

MSZ-FH06NA MSZ-FH09NA MSZ-FH12NA MSZ-FH15NA MSZ-FH18NA MSZ-FH18NA2

Power supply V, phase, Hz 208/230 , 1 , 60

Disconnect switch A 15

Min. circuit ampacity A 1.0

Fan motor F.L.A 0.67

Airﬂow

Super high - High -

Med. - Low - Quiet

COOL Dry

(Wet)

CFM

381- 304 - 221 - 167 - 137

(328 - 261 - 190 - 143 - 117)

381- 304 - 221 - 167 - 137

(328 - 261 - 190 - 143 - 117)

398 - 304 - 221 - 167 - 137

(342 - 261 - 190 - 143 - 117)

411 - 355 - 304 - 262 - 225

(354 - 305 - 261 - 225 - 194)

437 - 355 - 304 - 262 - 225

(376 - 305 - 261 - 225 - 194)

459 - 355 - 304 - 262 - 225

(395 - 305 - 261 - 225 - 194)

HEAT Dry CFM

437 - 325 - 225 - 167 - 140 437 - 325 - 225 - 167 - 140 454 - 325 - 225 - 167 - 140 497 - 394 - 317 - 254 - 201 514 - 394 - 317 - 254 - 201 514 - 394 - 317 - 254 - 201

Moisture removal pt./h 0.2 0.6 1.9 4.0 5.1 4.8

Sound level

Super high - High -

Med. - Low - Quiet

Cooling dB(A)

40 - 36 - 29 - 23 - 20 40 - 36 - 29 - 23 - 20 41 - 36 - 29 - 24 - 21 44 - 39 - 35 - 31 - 27 44 - 39 - 35 - 31 - 27 47 - 39 - 35 - 31 - 27

Heating dB(A)

42 - 36 - 29 - 24 - 20 42 - 36 - 29 - 24 - 20 42 - 36 - 29 - 24 - 21 46 - 39 - 34 - 29 - 25 46 - 39 - 34 - 29 - 25 46 - 39 - 34 - 29 - 25

Cond. drain connection O.D. in. 5/8

Dimensions

in.

36-7/16

D 9-3/16

H 12 (+ 11/16)

Weight Ib. 29

External ﬁnish Munsell 1.0Y 9.2/0.2

Remote controller Wireless type

Control voltage (by built-in transformer) 12 - 24 VDC

NOTE: Test conditions are based on AHRI 210/240.

Model Mode Function Airﬂow

(CFM)

Air speed

(ft./s)

Coverage

(ft.)

MSZ-FH06NA HEAT Dry 437 19.5 29.8

COOL Dry 381 17.0 26.1

Wet 328 14.6 22.5

MSZ-FH09NA HEAT Dry 437 19.5 29.8

COOL Dry 381 17.0 26.1

Wet 328 14.6 22.5

MSZ-FH12NA HEAT Dry 454 20.3 31.0

COOL Dry 398 17.8 27.3

Wet 342 15.3 23.5

MSZ-FH15NA HEAT Dry 497 22.2 33.8

COOL Dry 411 18.3 28.0

Wet 354 15.7 24.1

MSZ-FH18NA HEAT Dry 514 23.0 34.9

COOL Dry 437 19.5 29.8

Wet 376 16.7 25.6

MSZ-FH18NA2 HEAT Dry 514 23.0 34.9

COOL Dry 459 20.5 31.2

Wet 395 17.6 27.0

OBH683D

Unit: inch

MSZ-FH06NA MSZ-FH09NA MSZ-FH12NA MSZ-FH15NA MSZ-FH18NA MSZ-FH18NA2

OUTLINES AND DIMENSIONS

(MSZ-FH06/09/12NA) (MSZ-FH15/18NA/18NA2)

OBH683D

MSZ-FH06NA MSZ-FH09NA MSZ-FH12NA MSZ-FH15NA MSZ-FH18NA MSZ-FH18NA2

WIRING DIAGRAM

OBH683D

Indoor

heat

exchanger

Flared connection

Room temperature

thermistor

RT11

Flared connection

Refrigerant pipe ø3/8 (ø9.52)

(with heat insulator)

Refrigerant pipe ø1/4 (ø6.35)

(with heat insulator)

Indoor coil

thermistor

RT12 (main)

Indoor coil

thermistor

RT13 (sub)

Refrigerant flow in cooling

Refrigerant flow in heating

Unit: inch (mm)

REFRIGERANT SYSTEM DIAGRAM

MSZ-FH06NA MSZ-FH09NA MSZ-FH12NA

Indoor

heat

exchanger

Flared connection

Room temperature

thermistor

RT11

Flared connection

Refrigerant pipe ø1/2 (ø12.7)

(with heat insulator)

Refrigerant pipe ø1/4 (ø6.35)

(with heat insulator)

Indoor coil

thermistor

RT12 (main)

Indoor coil

thermistor

RT13 (sub)

Refrigerant flow in cooling

Refrigerant flow in heating

MSZ-FH15NA MSZ-FH18NA MSZ-FH18NA2

OBH683D

7-1. TIMER SHORT MODE

For service, the following set time can be shortened by bridging JPG and JPS on the electronic control P.C. board.

(Refer to 9-7.)

Set time: 3 minutes →3 seconds (It takes 3 minutes for the compressor to start operation. However, the starting time is

shortened by bridging JPG and JPS.)

7-2. HOW TO SET REMOTE CONTROLLER EXCLUSIVELY FOR A PARTICULAR INDOOR UNIT

A maximum of 4 indoor units with wireless remote controllers can be used in a room.

To operate the indoor units individually with each remote controller, assign a number to each remote controller according

to the number of the indoor unit.

This setting can be set only when all the following conditions are met:

• The remote controller is powered OFF.

• Weekly timer is not set.

• Weekly timer is not being edited.

(1) Hold down button on the remote controller for 2 seconds to enter the pairing mode.

(2) Press button again and assign a number to each remote controller.

Each press of button advances the number in the following order: 1 →2 →3 →4.

(3) Press button to complete the pairing setting.

After you turn the breaker ON, the remote controller that first sends a signal to an indoor unit will be regarded as the

remote controller for the indoor unit.

Once they are set, the indoor unit will only receive the signal from the assigned remote controller afterwards.

SERVICE FUNCTIONS

MSZ-FH06NA MSZ-FH09NA MSZ-FH12NA MSZ-FH15NA MSZ-FH18NA MSZ-FH18NA2

7-3. SETTING THE INSTALLATION POSITION

Be sure to set the remote controller according to the installed position of the indoor unit.

Installation position:

Left: Distance to objects (wall, cabinet, etc.) is less than 50 cm to the left

Center: Distance to objects (wall, cabinet, etc.) is more than 50 cm to the left and right

Right: Distance to objects (wall, cabinet, etc.) is less than 50 cm to the right

The installation position can be set only when all the following conditions are met:

• The remote controller is powered OFF.

• Weekly timer is not set.

• Weekly timer is not being edited.

(1) Hold down button on the remote controller for 2 seconds to enter the position setting mode.

(2) Select the target installation position by pressing button. (Each press of the button displays the

positions in order: center →right →left.)

(3) Press button to complete the position setting.

Installation position Left Center Right

Remote controller

display

(Left)(Center)(Right)

OBH683D

7-4. AUTO RESTART FUNCTION

When the indoor unit is controlled with the remote controller, the operation mode, the set temperature, and the fan speed

are memorized by the indoor electronic control P.C. board. “AUTO RESTART FUNCTION” automatically starts operation in

the same mode just before the shutoff of the main power.

Operation

If the main power has been cut, the operation settings remain.

After the power is restored, the unit restarts automatically according to the memory.

(However, it takes at least 3 minutes for the compressor to start running.)

How to disable “AUTO RESTART FUNCTION”

Turn off the main power for the unit.

Cut the jumper wire to JR77 on the indoor electronic control P.C. board. (Refer to 9-7.)

NOTE:

• The operation settings are memorized when 10 seconds have passed after the indoor unit was operated with the remote

controller.

• If main power is turned OFF or a power failure occurs while AUTO START/STOP timer is active, the timer setting is can-

celled.

• If the unit has been off with the remote controller before power failure, the auto restart function does not work as the

power button of the remote controller is OFF.

• To prevent breaker OFF due to the rush of starting current, systematize other home appliance not to turn ON at the same

time.

• When some air conditioners are connected to the same supply system, if they are operated before power failure, the

starting current of all the compressors may flow simultaneously at restart.

Therefore, the special counter-measures are required to prevent the main voltage-drop or the rush of the starting current

by adding to the system that allows the units to start one by one.

JR77

CN110CN151

Indoor electronic control

P.C. board

OBH683D

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Electric Klimaanlage Handbücher

Mitsubishi Electric

Mitsubishi Electric PQHY-P72TYHMU-A Anleitung zur Verwendung

Mitsubishi Electric

Mitsubishi Electric PLFY-P VCM-E2 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLFY-P NAMU-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PUMY-P200YKM2 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PUMY-P36NKMU3 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MXZ-SM36NAM Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MUZ-LN35VGHZ2-E1 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PKFY-P-VKM-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSY-D30NA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Mr. Slim PEAD-M71JA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PKH18FK3 Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric PFFY-P-NEMU-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FDF100VSXVD Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PUMY-P112VKM3 Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric MS-GF20VA-E1 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PEA-RP-EA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PUHZ-HRP-HA2 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MUZ-GA35VA-E3 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSZ-AP15VG Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Mr. SLim PEAD-140JA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PKFY-P VHM-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Mr.SLIM SLZ-M25FA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PAC-205FC Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PUHZ-P200YKA3 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Spheros

Spheros CC 355 Bedienungsanleitung

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Bedienungsanleitung

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Samsung

Samsung AR KV Series Leitfaden

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

Hitachi

Hitachi RAS-E24CAK Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Hisense

Hisense 7K Technisches Handbuch

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung