Mitsubishi Electric MS-GF20VA-E1 Bedienungsanleitung

CONTENTS

1. TECHNICAL CHANGES ··································· 2

2. PART NAMES AND FUNCTIONS····················· 3

3. SPECIFICATION················································ 4

4. NOISE CRITERIA CURVES ······························ 5

5. OUTLINES AND DIMENSIONS ························ 6

6. WIRING DIAGRAM············································ 6

7. REFRIGERANT SYSTEM DIAGRAM ··············· 7

8. SERVICE FUNCTIONS ····································· 8

9. MICROPROCESSOR CONTROL ··················· 10

10. TROUBLESHOOTING····································· 15

11. DISASSEMBLY INSTRUCTIONS ···················· 25

SPLIT-TYPE AIR CONDITIONERS

Outdoor unit service manual

MU-GF·VA Series (OBH622)

SERVICE MANUAL No. OBH621

INDOOR UNIT

PARTS CATALOG (OBB621)

NOTE:

RoHS compliant products have <G> mark on the spec name plate.

Models

MS-GF20VA -E1

MS-GF25VA -E1

MS-GF35VA -E1

MS-GF20VA - E1

MS-GF25VA - E1

MS-GF35VA - E1

1. New model

TECHNICAL CHANGES

Use the speciﬁed refrigerant only

Never use any refrigerant other than that specified.

Doing so may cause a burst, an explosion, or fire when the unit is being used, serviced, or disposed of.

Correct refrigerant is specified in the manuals and on the spec labels provided with our products.

We will not be held responsible for mechanical failure, system malfunction, unit breakdown or accidents caused by

failure to follow the instructions.

Prepare the proper tools.

Prepare the proper protectors.

Provide adequate ventilation.

After stopping the operation of the air conditioner, turn off the power-supply breaker and remove the power plug.

Discharge the capacitor before the work involving the electric parts.

Do not perform the work involving the electric parts with wet hands.

Do not pour water into the electric parts.

Do not touch the refrigerant.

Do not touch the hot or cold areas in the refrigeration cycle.

When the repair or the inspection of the circuit needs to be done without turning off the power, exercise great caution not to

touch the live parts.

OBH621

ACCESSORIES

PART NAMES AND FUNCTIONS

Model

MS-GF20VA

MS-GF25VA

MS-GF35VA

Installation plate 1

Installation plate ﬁxing screw 4 × 25 mm 5

Remote controller holder 1

Fixing screw for 3.5 × 16 mm (Black) 2

Battery (AAA) for remote controller 2

Wireless remote controller 1

Felt tape (For left or left-rear piping) 1

MS-GF20VA MS-GF25VA MS-GF35VA

Air ﬁlter

(Nano platinum ﬁlter)

Front panel

Air cleaning ﬁlter

(Electrostatic anti-allergy

enzyme ﬁlter, option)

Operation indicator lamp

Remote control receiving section

Emergency operation switch (E.O. SW)

Horizontal vane

Air outlet Heat exchanger

Display section

Air inlet

Remote controller

OBH621

SPECIFICATION

Indoor model MS-GF20VA MS-GF25VA MS-GF35VA

Function Cooling

Power supply Single phase 230 V, 50 Hz

Electrical

data

Running current A 0.20 0.22

Power input W 35 43

Fan

motor

Model RC4V18-FA

Current A 0.20 0.22

Dimensions W × H × D mm 798 x 295 x 232

Weight kg 9

Special remarks

Air direction 5

Airﬂow

Super High (POWERFUL)

m3/h

558 624

High 474 558

Med. 378 396

Low 246 288

Sound level

Super High (POWERFUL)

dB (A)

40 44

High 36 40

Med. 31 33

Low 25 26

Fan speed

Super High (POWERFUL)

rpm

1,000 1,100

High 880 1,000

Med. 740 770

Low 540 610

Fan speed regulator 4

Remote controller model KM12A

NOTE: Test conditions are based on ISO 5151.

Cooling: Indoor Dry-bulb temperature 27 Wet-bulb temperature 19

Outdoor Dry-bulb temperature 35 Wet-bulb temperature 24

Indoor-Outdoor piping length: 5 m

OBH621

10 63 125 250 500 1000 2000 4000 8000

NC-60

NC-50

NC-40

NC-30

NC-20

NC-70

BAND CENTER FREQUENCIES, Hz

COOLING

FUNCTION SPL(dB(A)) LINE

Super High

FAN SPEED

NC-10

OCTAVE BAND SOUND PRESSURE LEVEL, 0dB re 0.0002 MICRO BAR

10 63 125 250 500 1000 2000 4000 8000

NC-60

NC-50

NC-40

NC-30

NC-20

NC-70

BAND CENTER FREQUENCIES, Hz

COOLING

FUNCTION SPL(dB(A)) LINE

Super High

FAN SPEED

NC-10

OCTAVE BAND SOUND PRESSURE LEVEL, 0dB re 0.0002 MICRO BAR

Test conditions

Cooling: Dry-bulb temperature 27 °C

Wet-bulb temperature 19 °C

INDOOR UNIT

WALL

MICROPHONE

0.8m

10 63 125 250 500 1000 2000 4000 8000

NC-60

NC-50

NC-40

NC-30

NC-20

NC-70

BAND CENTER FREQUENCIES, Hz

COOLING

FUNCTION SPL(dB(A)) LINE

Super High

FAN SPEED

NC-10

OCTAVE BAND SOUND PRESSURE LEVEL, 0dB re 0.0002 MICRO BAR

NOISE CRITERIA CURVES

MS-GF20VA MS-GF25VA

MS-GF35VA

OBH621

Unit: mm

OUTLINES AND DIMENSIONS

211.5

231.5

253

21.5

155 155

80 225 225

5232

798

785 6.5

130619

295

100

107

112

33861

212.5

254

315 84

11×26 Oblong hole 11×20 Oblong hole

Installation plate

Indoor unit

Wall hole ø65

Air in

Air out

Installation plate

Piping

Drain hose

159

MS-GF20VA MS-GF25VA MS-GF35VA

Piping

Insulation ø35 O.D

Liquid line ø7 - 0.5 m (Flared connection ø6.35)

Gas line ø9.52 - 0.43 m (Flared connection: ø9.52)

Drain hose Insulation ø28 O.D Connected part ø16 O.D

WIRING DIAGRAM

MS-GF20VA MS-GF25VA MS-GF35VA

OBH621

Unit: mm

REFRIGERANT SYSTEM DIAGRAM

MS-GF20VA MS-GF25VA

Indoor

heat

exchanger

Flared connection

Room temperature

thermistor

RT11

Flared connection

Refrigerant pipe 6.35

(with heat insulator)

Indoor coil

thermistor

RT12

Refrigerant flow in cooling

Refrigerant pipe 9.52

(with heat insulator)

MS-GF35VA

Indoor

heat

exchanger

Flared connection

Room temperature

thermistor

RT11

Flared connection

Refrigerant pipe 6.35

(with heat insulator)

Indoor coil

thermistor

RT12

Refrigerant flow in cooling

Refrigerant pipe 9.52

(with heat insulator)

OBH621

8-1. TIMER SHORT MODE

For service, the following set time can be shortened by short circuit of JPG and JPS on the electronic control P.C. board.

(Refer to 10-7.)

Set time: 3 minutes →3 seconds (It takes 3 minutes for the compressor to start operation. However, the starting time is

shortened by short circuit of JPG and JPS.)

8-2. P.C. BOARD MODIFICATION FOR INDIVIDUAL OPERATION

A maximum of 4 indoor units with wireless remote controllers can be used in a room.

In this case, to operate each indoor unit individually by each remote controller, P.C. boards of remote controller must be

modified according to the number of the indoor unit.

How to modify the remote controller P.C. board

Remove batteries before modification.

The board has a print as shown below:

NOTE: For modification, take out

the batteries and press

the OPERATE/STOP (ON/

OFF) button 2 or 3 times at

first.

After modification, put back

the batteries then press the

RESET button.

Table 1

1 unit operation 2 units operation 3 units operation 4 units operation

No. 1 unit No modiﬁcation Same as at left Same as at left Same as at left

No. 2 unit — Solder J1 Same as at left Same as at left

No. 3 unit — — Solder J2 Same as at left

No. 4 unit — — — Solder both J1 and J2

How to set the remote controller exclusively for particular indoor unit

After you turn the breaker ON, the first remote controller that sends the signal to the indoor unit will be regarded as the remote

controller for the indoor unit.

The indoor unit will only accept the signal from the remote controller that has been assigned to the indoor unit once they are set.

The setting will be cancelled if the breaker is turned OFF, or the power supply is shut down.

Please conduct the above setting once again after the power has restored.

SERVICE FUNCTIONS

MS-GF20VA MS-GF25VA MS-GF35VA

The P.C. board has the print “J1” and “J2”. Solder “J1” and “J2” according to the number of indoor unit as shown in Table 1.

After modification, press the RESET button.

OBH621

8-3. AUTO RESTART FUNCTION

When the indoor unit is controlled with the remote controller, the operation mode, the set temperature, and the fan speed

are memorized by the indoor electronic control P.C. board. “AUTO RESTART FUNCTION” automatically starts operation

in the same mode just before the shutoff of the main power.

Operation

If the main power has been cut, the operation settings remain.

After the power is restored, the unit restarts automatically according to the memory.

(However, it takes at least 3 minutes for the compressor to start running.)

How to disable “AUTO RESTART FUNCTION”

Turn off the main power for the unit.

Solder the jumper wire to JR07 on the indoor electronic control P.C. board. (Refer to 10-7.)

NOTE:

• The operation settings are memorized when 10 seconds have passed after the indoor unit was operated with the remote

controller.

• If main power is turned OFF or a power failure occurs while AUTO START/STOP timer is active, the timer setting is can-

celled.

• If the unit has been off with the remote controller before power failure, the auto restart function does not work as the

power button of the remote controller is OFF.

• To prevent breaker OFF due to the rush of starting current, systematize other home appliance not to turn ON at the same

time.

• When some air conditioners are connected to the same supply system, if they are operated before power failure, the

starting current of all the compressors may flow simultaneously at restart.

Therefore, the special counter-measures are required to prevent the main voltage-drop or the rush of the starting current

by adding to the system that allows the units to start one by one.

JR07

Indoor electronic

control P.C. board

111NCA01NC 151NC 211NC

OBH621

WIRELESS REMOTE CONTROLLER

MICROPROCESSOR CONTROL

NOTE: Last setting will be stored after the unit is turned OFF with the remote controller. Indoor unit receives the signal of the

remote controller with beeps.

Signal transmitting section

Operation display section

Temperature buttons

OPERATE/STOP

(ON/OFF) button

Indication of

remote controller

model is on back

TIME SET buttons

FORWARD button

BACKWARD button

VANE CONTROL button

OFF-TIMER button

RESET button

FAN SPEED CONTROL button

OPERATION SELECT button

ECONO COOL button ON-TIMER button

CLOCK button

POWERFUL COOL button

MS-GF20VA MS-GF25VA MS-GF35VA

Operation Indicator lamp

The operation indicator at the right side of the indoor unit indicates the operation state.

•The following indication applies regardless of shape of the indication.

Indication Operation state Room temperature

The unit is operating to

reach the set temperature

About 2°C or more away

from set temperature

The room temperature is

approaching the set tem-

perature

About 1 to 2°C from set

temperature

INDOOR UNIT DISPLAY SECTION

Lighted

Blinking

Not lighted

9-1. COOL ( ) OPERATION

(1) Press OPERATE/STOP (ON/OFF) button.

OPERATION INDICATOR lamp of the indoor unit turns on with a beep tone.

(2) Select COOL mode with OPERATION SELECT button.

(3) Press TEMPERATURE buttons (TOO WARM or TOO COOL button) to select the desired temperature. The setting range

is 16 - 31°C.

1. Coil frost prevention

The compressor operational frequency is controlled by the temperature of the indoor heat exchanger to prevent the coil

from frosting.

When the temperature of indoor heat exchanger becomes too low, the coil frost prevention mode works.

The indoor fan operates at the set speed and the compressor stops. This mode continues until the temperature of indoor

heat exchanger rises.

OBH621

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Electric Klimaanlage Handbücher

Mitsubishi Electric

Mitsubishi Electric Mr. SLIM PEA-M180LAA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MFZ-KA25VA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric City Multi PQHY-P72 Anleitung zur Verwendung

Mitsubishi Electric

Mitsubishi Electric PAC-MK51BCB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MFZ-KJ25VE Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MXZ-4C36NAHZ Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PEFY Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PURY-P72 Anleitung zur Verwendung

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PQHY-P400YSGM-A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSZ-AP15VF Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M140EA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Mr. Slim MSY-A24NA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MXZ-2F33VF4-E1 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSZ-FH12NA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSZ-GF60VE Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric City Multi PEFY-P06NMSU-E Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric EB-50GU-A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PKFY-P VBM-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PUMY-P36NKMU4 Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric MSZ-GF20VA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PKFY-P-VAM-A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSZ-BT20VG Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSZ-SF15VA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSZ-HR25VF Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Spheros

Spheros CC 355 Bedienungsanleitung

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Bedienungsanleitung

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Samsung

Samsung AR KV Series Leitfaden

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

Hitachi

Hitachi RAS-E24CAK Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Hisense

Hisense 7K Technisches Handbuch

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung