Mitsubishi Electric Q62DAN Bedienungsanleitung

Digital-Analog Converter Module

User's Manual

-Q62DAN

-Q62DA

-Q64DAN

-Q64DA

-Q68DAVN

-Q68DAV

-Q68DAIN

-Q68DAI

-GX Configurator-DA (SW2D5C-QDAU-E)

A - 1

A-1

SAFETY PRECAUTIONS 

(Always read these precautions before using this equipment.)

Before using this product, please read this manual and the relevant manuals introduced in this manual

carefully and pay full attention to safety to handle the product correctly.

The precautions given in this manual are concerned with this product only. For the safety precautions of

the programmable controller system, refer to the user's manual for the CPU module used.

In this manual, the safety precautions are classified into two levels: " WARNING" and " CAUTION".

Indicates that incorrect handling may cause hazardous conditions,

resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions,

resulting in minor or moderate injury or property damage.

Under some circumstances, failure to observe the precautions given under " CAUTION" may lead to

serious consequences.

Observe the precautions of both levels because they are important for personal and system safety.

Make sure that the end users read this manual and then keep the manual in a safe place for future

reference.

[Design Precautions]

WARNING

Do not write data into the "System area" of the buffer memory of intelligent function modules.

Also, do not use any "Use prohibited" signals as an output signal to an intelligent function

module from the programmable controller CPU.

Writing data into the "System area" or outputting a signal for "Use prohibited" may cause a

malfunction of the programmable controller system.

CAUTION

Do not bunch the control wires or communication cables with the main circuit or power wires, or

install them close to each other.

They should be installed 100mm or more from each other.

Not doing so could result in noise that may cause malfunction.

At power on/off, voltage or current may instantaneously be output from the output terminal of this

module. In such case, wait until the analog output becomes stable to start controlling the

external device.

! !

WARNING!

CAUTION

A - 2

A-2

[Installation Precautions]

CAUTION

Use the programmable controller in an environment that meets the general specifications

contained in the user's manual of the CPU module to use.

Using this programmable controller in an environment outside the range of the general

specifications may cause electric shock, fire, malfunction, and damage to or deterioration of the

product.

While pressing the installation lever located at the bottom of module, insert the module fixing tab

into the fixing hole in the base unit until it stops. Then, securely mount the module with the fixing

hole as a supporting point.

Improper installation may result in malfunction, breakdown or the module coming loose and

dropping. Securely fix the module with screws if it is subject to vibration during use.

Tighten the screws within the range of specified torque.

If the screws are loose, it may cause the module to fallout, short circuits, or malfunction.

If the screws are tightened too much, it may cause damage to the screw and/or the module,

resulting in fallout, short circuits or malfunction.

Be sure to shut off all phases of the external power supply used by the system before mounting

or removing the module.

Not doing so may cause damage to the module.

In the system where a CPU module supporting Online module change is used and on the

MELSECNET/H remote I/O stations, modules can be replaced online (during energizing).

However, there are some restrictions on replaceable modules and the replacement procedures

are predetermined for each module.

For details, refer to the chapter of Online module change in this manual.

Do not directly touch the conductive area or electronic components of the module.

Doing so may cause malfunction or failure in the module.

[Wiring Precautions]

CAUTION

Always ground the FG terminal for the programmable controller.

There is a risk of electric shock or malfunction.

Use applicable solderless terminals and tighten with the specified torque. If any solderless spade

terminal is used, it may be disconnected when the terminal screw comes loose, resulting in

failure.

When turning on the power and operating the module after wiring is completed, always attach

the terminal cover that comes with the product.

There is a risk of electric shock if the terminal cover is not attached.

Tighten the terminal screws within the range of specified torque.

If the terminal screws are loose, it may result in short circuits or malfunction.

If the terminal screws are tightened too much, it may cause damage to the screw and/or the

module, resulting in short circuits or malfunction.

Be careful not to let foreign matter such as sawdust or wire chips get inside the module.

They may cause fires, failure or malfunction.

The top surface of the module is covered with protective film to prevent foreign objects such as

cable offcuts from entering the module when wiring.

Do not remove this film until the wiring is complete.

Before operating the system, be sure to remove the film to provide adequate ventilation.

A - 3

A-3

[Startup and Maintenance Precautions]

CAUTION

Do not disassemble or modify the modules.

Doing so could cause failure, malfunction injury or fire.

Be sure to shut off all phases of the external power supply used by the system before mounting

or removing the module.

Not doing so may cause failure or malfunction of the module.

In the system where a CPU module supporting Online module change is used and on the

MELSECNET/H remote I/O stations, modules can be replaced online (during energizing).

However, there are some restrictions on replaceable modules and the replacement procedures

are predetermined for each module.

For details, refer to the chapter of Online module change in this manual.

Do not install/remove the module to/from the base unit, or the terminal block to/from the module

more than 50 times after the first use of the product. (IEC 61131-2 compliant)

Failure to do so may cause malfunction.

Do not touch the connector while the power is on.

Doing so may cause malfunction.

Switch off all phases of the externally supplied power used in the system when cleaning the

module or retightening the terminal or module fixing screws.

Not doing so may cause failure or malfunction of the module.

If the screws are loose, it may cause the module to fallout, short circuits, or malfunction.

If the screws are tightened too much, it may cause damages to the screws and/or the module,

resulting in the module falling out, short circuits or malfunction.

Always make sure to touch the grounded metal to discharge the electricity charged in the body,

etc., before touching the module.

Failure to do so may cause a failure or malfunctions of the module.

[Disposal Precautions]

CAUTION

When disposing of this product, treat it as industrial waste.

A - 4

A-4

CONDITIONS OF USE FOR THE PRODUCT 

(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;

i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major or

serious accident; and

ii) where the backup and fail-safe function are systematically or automatically provided outside of the

PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.

(2) The PRODUCT has been designed and manufactured for the purpose of being used in general

industries.

MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT LIMITED

TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT, WARRANTY, TORT,

PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR LOSS OR DAMAGE TO

PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR USED IN APPLICATION NOT

INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS, OR WARNING CONTAINED IN

MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY MANUALS, TECHNICAL BULLETINS AND

GUIDELINES FOR the PRODUCT.

("Prohibited Application")

Prohibited Applications include, but not limited to, the use of the PRODUCT in;

Nuclear Power Plants and any other power plants operated by Power companies, and/or any other

cases in which the public could be affected if any problem or fault occurs in the PRODUCT.

Railway companies or Public service purposes, and/or any other cases in which establishment of a

special quality assurance system is required by the Purchaser or End User.

Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as Elevator

and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation, Equipment for

Recreation and Amusement, and Safety devices, handling of Nuclear or Hazardous Materials or

Chemicals, Mining and Drilling, and/or other applications where there is a significant risk of injury to

the public or property.

Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the

PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT is

limited only for the specific applications agreed to by Mitsubishi and provided further that no special

quality assurance or fail-safe, redundant or other safety features which exceed the general

specifications of the PRODUCTs are required. For details, please contact the Mitsubishi

representative in your region.

A - 5

A-5

REVISIONS

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

Dec., 1999 SH (NA)-080054-A First printing

Oct., 2000 SH (NA)-080054-B Add the contents of the function version B.

Correction

About the Generic Terms and Abbreviations, Section 2.1, Section 3.1.3,

3.3.1, 3.4, Section 4.3, Section 5.2.1, 5.2.2, 5.3.3, 6.5.1

Partial addition

Section 1.1, Section 3.1.1, 3.1.2, 3.2.1, 3.2.2, 3.3.1, 3.3.2, 3.4.3,

Section 4.5, Section 5.6.1, Section 7.2.3, 7.2.4

Addition

Section 1.2, Section 2.2, Section 3.2.3, Appendix 1

Dec., 2000 SH (NA)-080054-C Addition of Models

Q68DAV, Q68DAI

Correction

Section 3.2, 3.2.1, 3.2.2, 3.2.3, 3.3.1, 3.3.2, 3.4.1, 3.4.2, 3.4.3, 3.4.4,

3.4.6, 3.4.7, Section 4.5, Section 7.2.3, App-1.3

Partial addition

About the Generic Terms and Abbreviations, Product Structure,

Chapter 1, Section 1.1, Section 2.1, Section 3.1.1, 3.1.4, Section 4.1,

4.3, Section 7.1, Appendix 2

Jun., 2001 SH (NA)-080054-D Standardize the name from software package (GPP function) to Product

name (GX Developer).

Standardize the name from utility package (QDAU) to Product name

(GX Configurator-DA).

Correction

Conformation to the EMC Directive and Low Voltage Instruction, About

the Generic Terms and Abbreviations, Product Structure, Section 2.1,

2.2, Section 4.6, Section 5.2, 5.2.1, 5.2.2, 5.3.3, Appendix 1.2

Feb., 2002 SH (NA)-080054-E Add the contents of the function version B.

Correction

Product Structure, Section 1.2, Section 2.2, Section 3.2.2, 3.2.3, 3.4.1,

Section 4.2, 4.4.1, Section 5.3.3

Partial addition

SAFETY PRECAUTIONS, About the Generic Terms and Abbreviations,

Section 1.2, Section 2.1, Section 3.1.1, 3.2, 3.2.2, 3.2.3, Section 4.3,

4.6, Section 5.2.1, 5.2.2, Section 8.1, 8.2.1, Appendix 1

Addition

Section 3.4.2, 3.4.3, 3.4.4, 3.4.12, 3.4.13, 3.4.14, Chapter 7, App-2, 2.1,

2.2, 2.3

Renumbering

Section 3.4.2 to Section 3.4.8 Section 3.4.5 to Section 3.4.11,

Chapter 7 Chapter 8, Appendix 2 Appendix 3

A - 6

A-6

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

May, 2002 SH(NA)-080054-F Correction

Section 3.4.1, 3.4.2, 3.4.3, 3.4.4, 3.4.6, 3.4.13, 3.4.14, Section 4.5, 4.6,

Section 7.3.1, 7.3.2, 7.3.3, 7.3.4, 7.3.5, 7.3.6, 7.4, 7.5, Appendix 1.1,

2.2, 2.3

Partial addition

Section 3.3.2, Section 8.2.3

Feb., 2003 SH(NA)-080054-G Correction

SAFETY PRECAUTIONS, Section 1.2, Section 3.2, 3.4.1 to 3.4.4,

3.4.14, Section 4.5, Section 5.1, 5.2.1, 5.2.2, 5.3.2, 5.6.1 to 5.6.3,

Section 7.3.3 to 7.3.6, 7.4, Appendix 1.1 to Appendix 1.3, Appendix 2.2,

Appendix 2.3

Addition

Section 5.6.4, 5.6.5

May, 2003 SH(NA)-080054-H Correction

Section 2.2, Section 3.1.1, 3.4.1, 3.4.2, 3.4.3, 3.4.4, 3.4.13, 3.4.14,

Section 4.5, 4.6, Section 5.3.1

May, 2004 SH(NA)-080054-I Addition of program example for use on the remote I/O network

Correction

Section 2.2, Section 3.1.4, 3.2.1, 3.2.2, 3.4.7, Chapter 6, Section 7.1,

7.3.1 to 7.3.6

Aug., 2004 SH(NA)-080054-J Correction

Section 1.1, Section 5.1, 5.2.1, 5.2.2, 5.3.1, 5.3.2, 5.3.3, 5.6.1, 5.6.2,

5.6.3, Appendix 2.3

Partial addition

Section 5.6.4, Section 5.7, 5.8

Oct., 2004 SH(NA)-080054-K Correction

SAFETY PRECAUTIONS, Section 2.1, Section 3.1.1, Section 4.1,

Section 6.2, 6.2.1

Nov., 2005 SH (NA)-080054-L Addition of Models

Q62DAN, Q64DAN, Q68DAVN, Q68DAIN

Correction

SAFETY PRECAUTIONS, Conformation to the EMC Directive and Low

Voltage Instruction, Product Structure, Section 2.1, Section 5.2.2,

Section 6.2.2

Addition

Appendix 1.4

A - 7

A-7

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

Mar., 2006 SH (NA)-080054-M Correction

SAFETY PRECAUTIONS, Conformation to the EMC Directive and Low

Voltage Instruction, Section 2.1, 4.6, Appendix 2

Jan., 2007 SH (NA)-080054-N Correction

Section 3.2.1, Section 3.4.2, Section 4.6

Jun., 2007 SH (NA)-080054-O Correction

Section 4.3, Appendix 3

Jan., 2008 SH (NA)-080054-P Correction

SAFETY PRECAUTIONS, About the Generic Terms and Abbreviations

Section 1.1, Section 2.1, Section 2.3, Section 3.4.1 to Section 3.4.4,

Section 4.1, Section 4.6, Section 5.2.1, Section 5.2.2, Section 7.3.3,

Section 7.3.5, Section 8.1, Appendix 1.1, Appendix 2, Appendix 2.1,

Appendix 2.2, Appendix 2.3

Addition

Section 2.2

May, 2008 SH (NA)-080054-Q Correction

SAFETY PRECAUTIONS, Compliance with the EMC and Low Voltage

Directives, About the Generic Terms and Abbreviations, Section 2.1,

Section 4.1, Section 5.2.1, Section 5.2.2, Section 5.3.1, Section 5.3.3,

Section 7.1

Dec., 2010 SH (NA)-080054-R Correction

About the Generic Terms and Abbreviations, Product Structure,

Section 1.1, Sections 2.1 to 2.3, Section 3.1.1, Section 3.1.2,

Section 3.2.1, Section 3.2.2, Sections 3.4.1 to 3.4.4, Section 3.4.9,

Section 4.1, Section 4.3, Section 4.5, Section 5.2.1, Section 5.3.1,

Section 5.3.3, Section 5.4, Section 5.5, Section 5.6.1, Section 5.7,

Section 6.2, Section 6.2.2, Section 7.1, Sections 7.3.1 to 7.3.6,

Section 8.1, Section 8.2.3, Section 8.2.5, Appendix 2,

Appendices 2.1 to 2.3, Appendix 3

Addition

CONDITIONS OF USE FOR THE PRODUCT

May, 2015 SH (NA)-080054-S Correction

SAFETY PRECAUTIONS, RELEVANT MANUALS, Compliance with the

EMC and Low Voltage Directives, About the Generic Terms and

Abbreviations, Section 2.1, Section 2.2, Section 3.2.3, Section 4.3,

Section 4.6, Section 5.2.1, Section 5.2.2, Section 5.6.2, Section 5.6.3,

Section 6.1.2, Section 7.1, Section 7.3.6, Section 7.5, Appendix 3

A - 8

A-8

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

Jun., 2016 SH (NA)-080054-T Correction

Sections 4.3, Section 4.4.2, Section 4.5, Appendix 3

Addition

DISCONTINUED MODELS

Jun., 2017 SH (NA)-080054-U Correction

INTRODUCTION, COMPLIANCE WITH THE EMC AND LOW

VOLTAGE DIRECTIVES, ABOUT THE GENERIC TERMS AND

ABBREVIATIONS, Section 3.1.1

Japanese Manual Version SH-080027-X

This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent

licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property

rights which may occur as a result of using the contents noted in this manual.

1999 MITSUBISHI ELECTRIC CORPORATION

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Electric Controller Handbücher

Mitsubishi Electric

Mitsubishi Electric MELSEC-Q-MR-JE-C Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Central Controller G-50A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MR-J5-G Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FX2N-32CCL Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric A800 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Melservo-J5 MR-J5 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric TC-24A Handbuch

Mitsubishi Electric

Mitsubishi Electric MELSEC L-Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric QS0J61BT12 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FX2N-485-BD Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric AG-150A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric RJ51AW12AL Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FX3G SERIES Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R16MTCPU Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric MELDAS MDS-B-SVJ2 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric AE-200A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PAC-YT51CRB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric melsec-k Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC FX2NC-16MT-D/UL Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELDAS MDS-R Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric RD77GF8 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung