Mitsubishi Electric QJ71C24N Bedienungsanleitung

Q Corresponding Serial Communication Module

User's Manual (Basic)

-QJ71C24N

-QJ71C24N-R2

-QJ71C24N-R4

-QJ71C24

-QJ71C24-R2

-GX Configurator-SC (SW2D5C-QSCU-E)

A-1 A-1

SAFETY PRECAUTIONS 

(Read these precautions before using this product.)

Before using this product, please read this manual and the relevant manuals carefully and pay full attention

to safety to handle the product correctly.

The instructions given in this manual are concerned with this product. For the safety instructions of the

programmable controller system, please read the user's manual of the CPU module to use.

In this manual, the safety precautions are classified into two levels: " WARNING" and " CAUTION".

Under some circumstances, failure to observe the precautions given under " CAUTION" may lead to

serious consequences.

Observe the precautions of both levels because they are important for personal and system safety.

Make sure that the end users read this manual and then keep the manual in a safe place for future reference.

[Design Precautions]

WARNING

For the operation status of each station at communication error in each station, refer to the

respective manual for each station.

The communication error may result in an accident due to incorrect output or malfunction.

When using the notification function, the pager receiver may not be contacted due to the frequency

transmission status from the system setup environment and error on the receiver side.

To ensure the safety of the programmable controller system, install a call circuit with a lamp

display or buzzer sound.

When connecting a peripheral with the CPU module or connecting an external device, such as a

personal computer, with an intelligent function module to modify data of a running

programmable controller, configure an interlock circuit in the program to ensure that the entire

system will always operate safely.

For other forms of control (such as program modification or operating status change) of a

running programmable controller, read the relevant manuals carefully and ensure that the

operation is safe before proceeding.

Especially, when a remote programmable controller is controlled by an external device,

immediate action cannot be taken if a problem occurs in the programmable controller due to a

communication failure.

To prevent this, configure an interlock circuit in the program, and determine corrective actions to

be taken between the external device and CPU module in case of a communication failure.

A-2 A-2

[Design Precautions]

WARNING

Do not write any data to the "system area" of the buffer memory in the intelligent function

module.

Also, do not use any "use prohibited" signals as an output signal from the programmable

controller CPU to the intelligent function module.

Doing so may cause malfunction of the programmable controller system.

CAUTION

Do not install the control lines or communication cables together with the main circuit lines or

power cables.

Keep a distance of 100mm or more between them.

Failure to do so may result in malfunction due to noise.

When using the module while values, such as buffer memory set values, are registered in the

Flash ROM, do not turn off the power supply for the module loading station nor reset the

programmable controller CPU.

If the power supply for the module loading station is turned off or the programmable controller

CPU is reset while any values are registered, the data contents in the Flash ROM become

inconsistent and as a result the values must be set again in the buffer memory, etc. and

reregistered to the Flash ROM.

Also, this may cause failure and malfunction of the module.

[Installation Precautions]

CAUTION

Use the programmable controller in an environment that meets the general specifications in the

user's manual for the CPU module used.

Failure to do so may result in electric shock, fire, malfunction, or damage to or deterioration of

the product.

To mount the module, while pressing the module mounting lever located in the lower part of the

module, fully insert the module fixing projection(s) into the hole(s) in the base unit and press the

module until it snaps into place.

Incorrect mounting may cause malfunction, failure or drop of the module.

When using the programmable controller in an environment of frequent vibrations, fix the

module with a screw.

Tighten the screws within the specified torque range.

Undertightening can cause drop of the screw, short circuit or malfunction.

Overtightening can damage the screw and/or module, resulting in drop, short circuit, or

malfunction.

Shut off the external power supply (all phases) used in the system before mounting or removing

a module.

Failure to do so may result in damage to the product.

Do not directly touch any conductive parts and electronic components of the module.

Doing so can cause malfunction or failure of the module.

A-3 A-3

[Wiring Precautions]

CAUTION

When turning on the power and operating the module after installation and wiring are completed,

always attach the terminal cover that comes with the product.

There is a risk of electric shock if the terminal cover is not attached.

Perform correct pressure-displacement, crimp-contact or soldering for external wire connections

using the tools specified by the manufactures.

Incorrect connection may cause short circuits, fire, or malfunction.

Attach connectors to the module securely.

Place the cables in a duct or clamp them.

If not, dangling cable may swing or inadvertently be pulled, resulting in damage to the module or

cables or malfunction due to poor contact.

Before connecting the cables, check the type o f interface to be connected.

Connecting or erroneous wiring to the wrong interface may cause failure to the module and

external devices.

Tighten the terminal screws within the specified torque range.

Undertightening the terminal screws can cause short circuit or malfunction.

Overtightening can damage the screw and/or module, resulting in drop, short circuit, or

malfunction.

When disconnecting the cable from the module, do not pull the cable by the cable part. For the

cable with connector, hold the connector part of the cable.

For the cable connected to the terminal block, loosen the terminal screw.

Pulling the cable that is still connected to the module may cause malfunction or damage to the

module or cable.

Prevent foreign matter such as dust or wire chips from entering the module.

Such foreign matter can cause a fire, failure, or malfunction.

A protective film is attached to the top of the module to prevent foreign matter, such as wire

chips, from entering the module during wiring.

Do not remove the film during wiring.

Remove it for heat dissipation before system operation.

A-4 A-4

[Startup/Maintenance Precautions]

CAUTION

Do not disassemble or modify the modules.

Doing so may cause failure, malfunction, injury, or a fire.

Shut off the external power supply (all phases) used in the system before mounting or removing

the module.

Failure to do so may cause the module to fail or malfunction.

After the first use of the product, do not mount/remove the module to/from the base unit, and the

terminal block to/from the module more than 50 times (IEC 61131-2 compliant) respectively.

Exceeding the limit may cause malfunction.

Do not touch any terminal while power is on.

Doing so may cause malfunction.

Shut off the external power supply (all phases) used in the system before cleaning the module or

retightening the terminal screws or module fixing screws.

Failure to do so may cause the module to fail or malfunction.

Undertightening can cause drop of the screw, short circuit or malfunction.

Overtightening can damage the screw and/or module, resulting in drop, short circuit, or

malfunction.

Before handling the module, touch a conducting object such as a grounded metal to discharge

the static electricity from the human body.

Failure to do so may cause the module to fail or malfunction.

[Operation Precautions]

CAUTION

When changing data and operating status, and modifying program of the running programmable

controller from an external device such as a personal computer connected to an intelligent

function module, read relevant manuals carefully and ensure the safety before operation.

Failure to perform correct operations to change data, program, or the status may result in

system malfunction, machine damage, or an accident.

[Disposal Precautions]

CAUTION

When disposing of this product, treat it as industrial waste.

A-5 A-5

CONDITIONS OF USE FOR THE PRODUCT 

(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;

i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major or

serious accident; and

ii) where the backup and fail-safe function are systematically or automatically provided outside of the

PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.

(2) The PRODUCT has been designed and manufactured for the purpose of being used in general

industries.

MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT LIMITED TO

ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT, WARRANTY, TORT,

PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR LOSS OR DAMAGE TO

PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR USED IN APPLICATION NOT

INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS, OR WARNING CONTAINED IN

MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY MANUALS, TECHNICAL BULLETINS AND

GUIDELINES FOR the PRODUCT.

("Prohibited Application")

Prohibited Applications include, but not limited to, the use of the PRODUCT in;

Nuclear Power Plants and any other power plants operated by Power companies, and/or any other

cases in which the public could be affected if any problem or fault occurs in the PRODUCT.

Railway companies or Public service purposes, and/or any other cases in which establishment of a

special quality assurance system is required by the Purchaser or End User.

Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as Elevator

and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation, Equipment for

Recreation and Amusement, and Safety devices, handling of Nuclear or Hazardous Materials or

Chemicals, Mining and Drilling, and/or other applications where there is a significant risk of injury to

the public or property.

Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the

PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT is

limited only for the specific applications agreed to by Mitsubishi and provided further that no special

quality assurance or fail-safe, redundant or other safety features which exceed the general specifications

of the PRODUCTs are required. For details, please contact the Mitsubishi representative in your region.

A-6 A-6

REVISIONS

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

Dec., 1999 SH (NA)-080006-A First edition

Oct., 2000 SH (NA)-080006-B Add the contents of the function version B.

Correction

Contents, Entire manual (change MELSECNET/10H to MELSECNET/H),

About Manuals, About The Generic Terms and Abbreviations, Product

Configuration, Section 1.2, 1.2(8), 1.3 POINT, Section 2.2, 2.3, 2.5, 2.6,

Section 3.1, 3.6, 3.9, Section 4.2, 4.4.1(2)(a)(Figure), 4.6(1), Chapter

5(all), Section 6.1.1, 6.1.3, 6.1.4, Section 7.1.1, 7.1.2, 7.2.2, Section 8.1,

8.2.1, 8.2.2, 8.3.1, 8.3.2, Section 9.2 to 9.7, Section 10.1.1, 10.2.1,

10.3.8, 10.3.18, Appendix 1.1(2), Appendix 2(all), Appendix 3(2),

Appendix 7, Appendix 8

Addition

Entire manual (add the explanation on MELSECNET/H remote I/O

station), The Manual's Use and Structure, Section 2.1, Section

3.1(Table), Section 4.4.2(1)(d), 4.9.2, Section 8.3.2 POINT, Section

10.2.1 (7164H, 7E70H), Appendix 3(1)

Jun., 2001 SH (NA)-080006-C Put Windows base software product together from Mitsubishi

Programmable Controller MELSEC Series to Mitsubishi integrated FA

Software MELSOFT Series.

Standardize the name from software package (GPP function) to Product

name (GX Developer).

Standardize the name from utility package (QSCU) to Product name (GX

Configurator-SC).

Correction

Conformation to the EMC Directive and Low Voltage Instruction, About

the Generic Terms and Abbreviations, Product Configuration, Program

Examples (Section 6.1.4, 6.2.3, Section 7.2.3, Section 9.3, 9.5, Appendix-

8), Section 1.2(1)(d), 1.2(4)(b)(Diagram), 1.2(8)(b), 1.3, Section 2.1, 2.3,

2.4, 2.5, 2.7, Section 3.1(Table), 3.2.1(3), 3.3.3(2), 3.4(Table), 3.9,

Section 4.3, 4.5.2, Section 5.1.5(3), 5.2, Section 6.1.4, Section 8.2, 8.3.2

POINT, 8.4.2, 8.4.9(Table), 8.6.3(Table), 8.6.7(Table), Section 10.1.2(b),

10.3(Table), Appendix 1.1, 2.1, 6, 7, 9

Addition

Section 2.6, Section 8.4.4, 8.6.2(Table), Section 10.2.1(716FH, 7FEFH),

10.2.3(7FE9H), 10.3.14, Appendix 3

Feb., 2002 SH (NA)-080006-D

Addition

About The Generic Terms and Abbreviations, Section 1.2, Section 2.1,

2.7, Section 4.5.2, Section 8.2.1, 8.2.2, Section 10.2.1, Appendix 1.1, 6

Oct., 2002 SH (NA)-080006-E

Addition

The Manual's Use and Structure, About The Generic Terms and

Abbreviations, Section 1.2(1)(4), Section 2.1, 2.4, Section 5.2, Section

6.1.4, Section 9.8, Appendix 7

Jan., 2003 SH (NA)-080006-F

Addition model

QJ71C24N, QJ71C24N-R2, QJ71C24N-R4

A-7 A-7

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

Jan., 2003 SH (NA)-080006-F

Addition

SAFETY PRECAUTIONS, About Manuals, About The Generic Terms

and Abbreviations, Product Configuration, Section 1.3, Section 2.1, 2.2,

2.3, 2.5, 2.6, 2.7, Section 3.1, 3.2.1, 3.3.1, 3.6, 3.8, 3.9, Section 4.1, 4.3,

4.4, 4.5, 4.6, 4.7.1, Section 6.1.1, 6.1.2, Section 7.1, 7.2.2, Chapter 8(all),

Section 9.1, 9.6, Section 10.1.2(b), 10.1.3(1), 10.2, Appendix 1, Appendix

2.1, Appendix 3, Appendix 5, Appendix 9

Jun., 2004 SH (NA)-080006-G

Correction

About The Generic Terms and Abbreviations, Product Configuration,

Chapter 2 (all), Section 3.8, Section 4.2.2 (1), Section 5.1.3 POINT,

Section 5.1.4, Chapter 8 (screen change), Section 8.6.10, Section 10.1.1,

Section 10.2

Addition

Appendix 9

Sep., 2004 SH (NA)-080006-H

Correction

Section 1.3, Section 2.5, 2.6, Section 3.5, 3.6, 3.9, Section 4.1, Chapter 8

(screen change), Section 8.6.9, 8.6.10, Section 10.1, 10.2, Appendix 1.1

Addition

Appendix 9.12

Feb., 2005 SH (NA)-080006-I

Correction

Section 2.1 (1), Section 3.1, Section 4.5.2 (1) ©, Chapter 9 (Simultaneous

execution of dedicated instructions), Section 10.2.1

Aug., 2005 SH (NA)-080006-J

Correction

SAFETY PRECAUTIONS, Section 3.3.1, 3.3.3, Section 8.2.2,

Section 9.4, Appendix 5, Appendix 7.1, 7.2

Feb., 2006 SH (NA)-080006-K

Correction

Section 2.6, Section 3.9, Section 8.2.1, 8.3.3, Section 9.1, Appendix 5

Mar., 2006 SH (NA)-080006-L

Correction

SAFETY PRECAUTIONS, Section 1.3, Section 2.6, Section 3.2.1, 3.8,

3.9, Section 8.6.9, Section 10.2.1, 10.3.11, Appendix 1

Addition

Section 10.1.7

Jan., 2008 SH (NA)-080006-M

Change of a term

"PLC" was changed to "programmable controller".

Correction

About The Generic Terms and Abbreviations, Section 1.2, 1.3, Section

2.1, 2.5, 2.7, Section 3.2.1, 3.2.2, 3.3.1, 3.9, Section 4.1, 4.3, 4.4, 4.5.2,

4.6, 4.9.2, Section 5.1.4, 5.2, Section 6.1.6, Chapter 8, Section 9.2 to 9.8,

Section 10.1.1, 10.1.6, 10.2.1,10.2.3, 10.3.3, 10.3.4, 10.3.8, 10.3.11,

10.3.19, Appendix 1.1, Appendix 2.1, Appendix 3, Appendix 5, Appendix

7.1

Addition

Section 2.5, Appendix 1.3

A-8 A-8

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

May, 2008 SH (NA)-080006-N

Correction

SAFETY PRECAUTIONS, About Manuals, Compliance with the EMC

and Low Voltage Directives, About The Generic Terms and

bbreviations, Section 1.2, 1.3, Section 2.1 to 2.3, 2.8, Section 4.1, 4.5.2,

Section 5.1.1, Section 8.2.1, 8.3.2, 8.3.3, Section 9.8, Section 10.1.1,

10.2.1, 10.3.3, 10.3.6, Appendices 1.1, 2.1, 3

Addition

Section 2.7

June, 2009 SH (NA)-080006-O

Correction

About Manuals, Manual's Use and Structure, About The Generic Terms

and Abbreviations, Definitions and Descriptions of Terminology,

Sections 1.2, 1.3, 2.1, 2.2, 2.4 to 2.6,

2.8, 3.1, 3.2.1, 3.3.4, 3.4 to 3.6, 3.8, 3.9, 4.1 to 4.3,

4.4.2, 4.5.2, 4.5.3, 4.6, 4.7, 4.7.1, 5.1.4, 5.1.5, 6.1.2,

6.1.4, 6.2.2, 7.1.2, and 7.2.2, Chapter 9, Sections 9.1, 9.2.1, 9.2.2,

9.3.1, 9.4, 9.4.5, 9.6.1, 9.6.3, 10.2 to 10.8, 11.1.1, 11.1.2, 11.1.5,

11.1.6, 11.2.1, 11.3, 11.3.1 to 11.3.3,

and 11.3.5 to 11.3.22, Appendices 1.1, 2.1, 3, 9.6, and 10

Partial addition

Section 3.3.4, Chapter 8, Sections 9.4.9, 9.6.7, 11.3.4, and 11.3.6

Section number change

Chapters 8 to 10 9 to 11, Sections 9.6.7 to 9.6.10 9.6.8 to 9.6.11,

Sections 9.4.9 to 9.4.11 9.4.10 to 9.4.12,

Section 11.3.4 11.3.5, Sections 11.3.5 to 11.3.20 11.3.7 to 11.3.22

Apr., 2011 SH (NA)-080006-P

Correction

SAFETY PRECAUTIONS, About The Generic Terms and Abbreviations,

Sections 1.2, 1.3, 2.1, 2.2, 2.8, 3.2.1, 3.2.2, 3.3.1, 3.3.2, 3.8, 4.4, 5.2,

6.1.1, 6.1.3, 9.2.1, 9.2.2, 10.1, 10.4, 11.2.1, 11.3.3, 11.3.8, 11.3.21,

Appendices 1.1, 3, 6, 7.1

Addition

CONDITIONS OF USE FOR THE PRODUCT, Sections 8.1.5, 8.1.6, 10.7

Section number change

Section 10.8 10.9

Nov., 2012 SH (NA)-080006-Q

Correction

COMPLIANCE WITH THE EMC AND LOW VOLTAGE DIRECTIVES,

Sections 1.3, 3.2.1, 8.1.5, 8.1.6, 9.2.2, 11.2.1, 11.3.1, Appendix 3

Partial addition

Appendix 6

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Electric Controller Handbücher

Mitsubishi Electric

Mitsubishi Electric Melservo-Jet MR-JET-G Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric XD3500U Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric qd63p6 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric -MR-CV Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q170MSCPU Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO MR-JET-G-N1 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PAC-YT51CRB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-RJ71EN71 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO JET Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PAC-YG66 DCA-J Service-Handbuch

Mitsubishi Electric

Mitsubishi Electric MELSEC-Q-MR-JE-C Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5 Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric CR800-D Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FX5-DP-M Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric RD77MS2 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric QJ71GF11-T2 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric PAC-YT51CRA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC-A/QnA Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric CR800 Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung