Mitsubishi Electric XD3500U Bedienungsanleitung
EN-1
LAN Control Utility
User Manual (for XD3500U)
Contents
Preparation/SetUp .........................................................................2
Preparation before using the network function...........................................2
Connection..................................................................................................3
Installation...................................................................................................3
Setting the IP address of the projector .......................................................5
When using a DHCP server ...........................................................................................6
When not using a DHCP server.....................................................................................7
Telnet setting...............................................................................................8
Setting the password (Password Setup) .......................................................................9
Setting the display language of ProjectorView (language) ..........................................10
Setting the LAN control (LAN-Controlled Mode) .........................................................10
Setting the PJLink™ certification (PJLink certification Mode).....................................11
Save and exit ...............................................................................................................11
ProjectorView...............................................................................12
Using the ProjectorView............................................................................12
How to start up ............................................................................................................12
VIRTUAL REMOTE controller.......................................................................................14
E-mail notification function ..........................................................................................14
Initial setting.................................................................................................................15
Support for the PJLink™ function ...............................................16
EN-2
Preparation/SetUp
Preparation before using the network function
This projector is equipped with the network function to control and monitor the projector’s operations using a Web
browser and to send e-mail notification.
Before using the network function, perform the following three preparation steps.
(1) Setup of the application software “Projector-Control Device Installer”
(2) Setting of the IP address of the projector*1
(3) Setting of password, display language, LAN control, and PJLink™ certification using telnet.
*1 When setting IP addresses for multiple projectors collectively or when setting an IP address for a ceiling-
mounted projector after installation, check and take a note of combination of the projectors and the hardware
addresses (MAC addresses) in advance. To check the hardware addresses (MAC addresses), perform step 2
on the page 5.
[Major functions]
Setting of the projector’s IP address
Setting of password, display language, and LAN control
PJLink™ certification setting (Telnet function)
Startup of the controlling / supervising tool (ProjectorView) using the Web browser
[System requirements]
Supported OS : Windows®2000, Windows®XP, Windows Vista®
Microsoft®.NET Framework 2.0*2 should be installed in Windows®2000 or Windows®XP.
Microsoft®.NET Framework 3.0*3 should be installed in Windows Vista®.
CPU : Pentium II 233 MHz or higher
Memory : 128 MB or more
Free HDD space : 32 MB or more
Web browser : Internet Explorer Ver. 6.0
(Java Plug-in*4 should be installed and JavaScript should be enabled.)
How to install Microsoft®.NET Framework Version 2.0, 3.0
*2 When using Windows®2000 or Windows®XP:
(1) Download .NET Framework Version 2.0 (file named “dotnetfx.exe”) from the download center on the
Microsoft®Web site (http://www.microsoft.com/downloads/).
(When the file is unavailable from the above-mentioned URL, search for .NET Framework using Windows
Update and access the download site found.)
(2) Execute the downloaded file named dotnetfx.exe.
*3 When using Windows Vista®:
(1) Download .NET Framework Version 3.0 (file named “dotnetfx3.exe”) from the download center on the
Microsoft®Web site (http://www.microsoft.com/downloads/).
(When the file is unavailable from the above-mentioned URL, search for .NET Framework using Windows
Update and access the download site found.)
(2) Execute the downloaded file named dotnetfx3.exe.
*4 How to install Java Plug-in
(1) Download JRE6 from the JAVA download center on the Sun Microsystems Web site (http://java.sun.com/
javase/downloads/index.jsp).
(When the file is unavailable from the above-mentioned URL, search for “JRE6 download” using a search
engine and access the download site found.)
(2) Execute the downloaded file.
(3) After the completion of the installation, select [Start] - [Control Panel] - [Java Plug-in] and disable the cache.
Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation•
in the United States and/or other countries.
Pentium is trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and•
other countries.
The trademark of PJLink is trademark applied for registration or registered trademark in Japan, the United•
States, and other countries and areas.
Other brand or product names are trademarks or registered trademarks of their respective holders.•
EN-3
1
Copy two files (DI_4.1.3.6.msi and Setup.exe) contained in the Tools folder of CD-ROM to the hard disk of
your personal computer.
2
Double-click the file named Setup.exe.
3
When the following window appears, click Next.
Installation
Before starting installation, be sure to read “ReadMe.txt” contained in the CD-ROM.
Connection
Preparation/SetUp (continued)
Computer
To LAN terminal
LAN cable (option)
(100BASE-TX or 10BASE-T should be supported.)
LAN cable (option)
(100BASE-TX or 10BASE-T
should be supported.)
External HUB
Use a straight-through category-5 cable for LAN connection.•
Don’t touch the metal parts of the LAN connector and LAN cable because static electricity may be discharged•
from your body, causing damage to the projector.
When STANDBY MODE of the INSTALLATION menu of the projector is set to LOW, the LAN network is
disabled. To enable the LAN network, set STANDBY MODE to STANDARD. (See the User Manual of the
projector.)
EN-4
Preparation/SetUp (continued)
4
Select a folder to install the program, and click Next.
5
Click Next.
6
Installation starts.
The progress of the installation process is•
displayed as shown on the right.
7
When the installation process is completed, click
Close.
How to remove Projector-Control Device Installer
Select [Start] - [Control Panel] - [Add or Remove Programs] - [Projector-Control Device Installer] and click
[Remove] (in the case of Windows®XP).
EN-5
1
Start the Projector-Control Device Installer.
Select [Start] - [All Programs] - [Projector] -•
[Projector-Control Device Installer] (in the case of
Windows®XP).
2
Click the Search button.
Projector is recognized.•
(Note)
When projector isn’t recognized, check the following.
The firewall function has been disabled. (When it•
has been enabled, search may not be conducted.)
The personal computer and the projector are on•
the same network. (For preventing unauthorized
access.)
More than one Projector-Control Device Installer•
isn’t running.
The network adapter being used is selected by•
the Option setting of the Tool menu.
“STANDBY MODE” of the projector is set to•
“STANDARD.”
3
Select a projector by clicking the line showing the
projector and click the Assign IP button.
Click here
4
The Assign IP Address screen appears.
Setting the IP address of the projector
Before setting the IP address, check that the projector has been LAN-networked and turn on the main power of
the projector.
When using multiple projectors, connect and configure them one by one. If you turn on the powers of the•
projectors that are connected but not yet configured at the same time, they may not be recognized.
For automatic IP address setting by the DHCP server, go to page 6. For IP address setting without using the•
DHCP server, go to page 7.
Preparation/SetUp (continued)
EN-6
5
Select [Obtain an IP address automatically] and click
Next.
6
Click Next.
Check that the options are marked with•
checkmarks as shown on the right. Keep them
unchanged for normal use.
7
Click Assign.
8
Click Finish.
9
Click the Search button.
Check the IP address.•
When using a DHCP server
Preparation/SetUp (continued)
EN-7
5
Select [Assign a specific IP address] and click Next.
6
Enter a fixed IP address (for example, 192.168.0.1)
and click Next.
(Note)
Do not use 0 or 255 for the last digit of the IP
address.
7
Click Assign.
8
Click Finish.
9
Click the Search button.
Check the IP address you set.•
(Note)
When using the error/alert e-mail notification function
described later, click the Assign IP button and set the
subnet mask and default gateway correctly.
For the values of the subnet mask and default•
gateway, contact your network administrator.
When not using a DHCP server
Preparation/SetUp (continued)
EN-8
1
Start the Projector-Control Device Installer.
Select [Start] - [All Programs] - [Projector] -•
[Projector-Control Device Installer] (in the case of
Windows®XP).
2
Press the +buttons on the left pane to expand the
tree structure until the IP address you set appears.
3
Click the Telnet Configuration tab.
4
Select the Connect tab. Press the Enter key within
5 seconds after the message shown on the right
appears.
When it passes 5 seconds without any operation•
on this screen, the screen is shaded and no key
operation is accepted. In this case, click the
Connect button again to continue setting.
5
The setting menu appears.
Telnet setting
Setting of password, display language, LAN control, and PJLink™ certification using telnet.
This section describes how to set the password, display language on the ProjectorView screen, LAN control, and
PJLink™ certification that are necessary for the operation state control tool (commercially available) that uses the
projector operation control/monitor tool ProjectorView and the industry standard PJLink™ protocol.
Preparation/SetUp (continued)
EN-9
1
Enter “0” and press the Enter key.
2
Input the old (current) password and press the Enter
key. (Default password is admin.)
If you input a wrong password, an error message•
appears and the setting menu is displayed again.
In this case, set the password again.
If you forget your password, select “7•
factory defaults,” input the password
“projectorcontroller,” and then select “9 save and
exit” to perform initialization.
3
Input a new password (example: “proj2000”) and
press the Enter key.
(Note)
Use single-byte alphanumeric characters only.
4
Input the new password (example: “proj2000”) again
and press the Enter key.
If you input a wrong password, an error message•
appears and the setting menu is displayed again.
In this case, set the password again.
Setting the password (Password Setup)
Preparation/SetUp (continued)
EN-10
1
Enter “3” and press the Enter key.
2
To enable the e-mail notification function of
ProjectorView, enter “1” and press the Enter
key. (Default is OFF (0).) (See pages 12 - 15 for
ProjectorView function.)
Setting the LAN control (LAN-Controlled Mode)
Preparation/SetUp (continued)
1
Enter “1” and press the Enter key.
2
Enter “0” for English or “1” for Japanese.
Setting the display language of ProjectorView (language)
Andere Handbücher für XD3500U
1
Inhaltsverzeichnis
Andere Mitsubishi Electric Controller Handbücher
Mitsubishi Electric
Mitsubishi Electric FX2N-485-BD Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric MELSEC iQ-F FX5 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q Series Betriebsanleitung
Mitsubishi Electric
Mitsubishi Electric AJ65BT64DAV/DAI Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric MELSEC iQ-R Series Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric NZ2MFB2-16A Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric FX3U-1PG Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric MELSEC iQ-R Series Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric MDS-EX-CVP Series Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric MELSEC Q Series Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric MELSEC Q Series Betriebsanleitung
Mitsubishi Electric
Mitsubishi Electric MELSEC iQ-F Series Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric MELSEC iQ-F FX5 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric MELSEC FX3U-485ADP-MB Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric AE-200A Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric PAC-YT51CRB Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric MR-J5-G Series Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric NZ2GF12A4-16D Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric NZ2GN2S-D41P01 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric MELSEC FX Series Betriebsanleitung
Mitsubishi Electric
Mitsubishi Electric MR-J5-G Series Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric melsec q01ucpu Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric A1SJ71PB96F Bedienungsanleitung
