Mitsubishi Electric 800 Series Bedienungsanleitung

INSTRUCTION MANUAL

INVERTER

Plug-in option

PRE-OPERATION INSTRUCTIONS 1

INSTALLATION 2

PARAMETER LIST 3

ANALOG OUTPUT 4

DIGITAL OUTPUT 5

FR-A8AY E KIT

Analog output function

Digital output function

Safety instructions

Thank you for choosing this Mitsubishi Electric inverter plug-in option.

This Instruction Manual provides handling information and precautions for use of this product. Incorrect handling might cause an unexpected

fault. Before using this product, read all relevant instruction manuals carefully to ensure proper use.

Please forward this Instruction Manual to the end user.

Electric Shock Prevention

WARNING

Do not remove the front cover or the wiring cover while the power of the inverter is ON, and do not run the inverter with the front cover or the

wiring cover removed. Otherwise you may access the exposed high voltage terminals or the charging part of the circuitry and get an electric

shock.

Do not remove the inverter front cover even if the power supply is disconnected. The only exception for this would be when performing wiring

and periodic inspection. You may accidentally touch the charged inverter circuits and get an electric shock.

Before wiring or inspection, LED indication of the inverter unit operation panel must be switched OFF. Any person who is involved in wiring or

inspection shall wait for at least 10 minutes after the power supply has been switched OFF and check that there is no residual voltage using

a tester or the like. For some time after the power-OFF, a high voltage remains in the smoothing capacitor, and it is dangerous.

Any person who is involved in wiring or inspection of this product shall be fully competent to do the work.

The plug-in option must be installed before wiring. Otherwise you may get an electric shock or be injured.

Do not touch the plug-in option or handle the cables with wet hands. Doing so may cause an electric shock.

Do not subject the cables to scratches, excessive stress, heavy loads or pinching. Doing so may cause an electric shock.

WARNING Incorrect handling may cause hazardous conditions, resulting in death or severe injury.

Incorrect handling may cause hazardous conditions, resulting in medium or slight injury, or may cause only material

damage.

Do not attempt to install, operate, maintain or inspect this product until you have read this Instruction Manual and supplementary

documents carefully. Do not use this product until you have a full knowledge of this product mechanism, safety information and

instructions. In this Instruction Manual, the safety instruction levels are classified into "WARNING" and "CAUTION".

CAUTION

Note that even the level may lead to a serious consequence depending on conditions. Be sure to follow the

instructions of both levels as they are critical to personnel safety.

CAUTION

Injury Prevention

Additional Instructions

The following instructions must be also followed. If the product is handled incorrectly, it may cause unexpected fault, an injury, or an electric

shock.

CAUTION

The voltage applied to each terminal must be the ones specified in the Instruction Manual. Otherwise an explosion or damage. may occur.

The cables must be connected to the correct terminals. Otherwise an explosion or damage may occur.

The polarity (+ and -) must be correct. Otherwise an explosion or damage may occur.

While power is ON or for some time after power OFF, do not touch the inverter as it will be extremely hot. Touching these devices may cause

burns

CAUTION

Transportation and mounting

Do not install or operate the plug-in option if it is damaged or has parts missing.

Do not stand or rest heavy objects on the product.

Ensure the mounting orientation of this product is correct.

Foreign conductive objects must be prevented from entering the inverter. That includes screws and metal fragments or other flammable

substance such as oil.

If halogens (including fluorine, chlorine, bromine, and iodine) contained in fumigants for wood packages enter this product, the product may

be damaged. Prevent the entry of fumigant residuals or use an alternative method such as heat disinfection. Note that sterilization or

disinfection of wood packages should be performed before packing the product.

Trial run

Before starting operation, each parameter must be confirmed and adjusted. A failure to do so may cause some machines to make

unexpected motions.

WARNING

Usage

Do not modify the equipment.

Do not perform parts removal which is not instructed in this manual. Doing so may lead to fault or damage of the product.

CAUTION

Usage

When parameter clear or all parameter clear is performed, the required parameters must be set again before starting operations. Because all

parameters return to their initial values.

Static electricity in your body must be discharged before you touch the product.

Maintenance, inspection and parts replacement

Do not carry out a megger (insulation resistance) test.

Disposal

The inverter must be treated as industrial waste.

General instruction

Many of the diagrams and drawings in this Instruction Manual show the inverter without a cover or partially open for explanation. Never

operate the inverter in this manner. The cover must be reinstalled and the instructions in the Instruction Manual must be followed when

operating the inverter.

— CONTENTS —

Safety instructions 2

1 PRE-OPERATION INSTRUCTIONS 7

1.1 Unpacking and checking the product............................................................................................................................7

1.1.1 Product confirmation ............................................................................................................................................................. 7

1.2 Component names ..........................................................................................................................................................8

1.3 Specifications ..................................................................................................................................................................9

2 INSTALLATION 10

2.1 Pre-installation instructions .........................................................................................................................................10

2.2 Installation procedure ...................................................................................................................................................10

2.3 Wiring..............................................................................................................................................................................18

3 PARAMETER LIST 22

4 ANALOG OUTPUT 24

4.1 Connection diagram ......................................................................................................................................................24

4.2 Terminals........................................................................................................................................................................25

4.3 Extended analog output function parameter list ........................................................................................................26

4.4 Adjustment procedure ..................................................................................................................................................27

4.4.1 Analog output signal voltage/current switchover (Pr.309) setting ....................................................................................... 27

4.4.2 Meter calibration ................................................................................................................................................................. 29

4.4.3 Setting output signals.......................................................................................................................................................... 31

4.4.4 Adjusting the analog signal (Pr.307, Pr.308, Pr.311, Pr.312) ............................................................................................. 32

4.5 Precautions ....................................................................................................................................................................34

5 DIGITAL OUTPUT 35

5.1 Terminals........................................................................................................................................................................35

5.2 Digital output function parameter list..........................................................................................................................36

5.3 Parameter setting ..........................................................................................................................................................36

APPENDIX 38

Appendix 1 Instructions for compliance with the EU Directives ....................................................................................38

Appendix 2 Instructions for EAC .......................................................................................................................................39

Appendix 3 Restricted Use of Hazardous Substances in Electronic and Electrical Products .....................................40

Appendix 4 Referenced Standard (Requirement of Chinese standardized law) ...........................................................41

REVISIONS 43

PRE-OPERATION INSTRUCTIONS 7

1PRE-OPERATION INSTRUCTIONS

1.1 Unpacking and checking the product

Take the plug-in option out of the package, check the product name, and confirm that the product is as you ordered and intact.

This product is a plug-in option made for the FR-E800 series inverters.

1.1.1 Product confirmation

Check the enclosed items.

Plug-in option: 1 Mounting screw (M3 8

mm): 2

(Refer to page 11, page

13.)

Junction connector: 1

(Refer to page 11, page

13.)

Option small cover: 1

(Refer to page 13.)

Front cover for plug-in

option: 1

(Refer to page 11, page

13.)

Recessed neck screw

(M3 × 7): 1

(Refer to page 11, page

13.)

Straight spacer: 1

(Refer to page 11, page

13.)

L-shaped spacer: 1

(Refer to page 11, page

13.)

Hexagon spacer: 2

(Refer to page 11, page

13.)

8PRE-OPERATION INSTRUCTIONS

1.2 Component names

Symbol Name Description Refer to

page

a Mounting hole Used to fix this product to the inverter by inserting a mounting screw or a spacer. 10

b Terminal block Connects the device to input the signal to the inverter, and the device to receive

the signal from the inverter. 18

cSwitch for manufacturer

setting Switch for manufacturer setting. Do not change the initial setting ( ). ─

d Connector Connected to the junction connector, which is connected to the option connector

on the inverter. 10

Front view Rear view

(a)

(b)

(d)

(c)

(a)

AM0

AM1

AMC

PRE-OPERATION INSTRUCTIONS 9

1.3 Specifications

Analog output

Digital output

Open collector output specification: permissible load of 24 VDC 0.1 A

Item Voltage output Current output

Output signal 0 to ±10 VDC max (across terminals AM0 to AMC) 0 to 20 mADC (across terminals AM1 to AMC)

Output resolution 3 mV 10 mA

Applicable meter

DC voltmeter

Full-scale ±10 V (internal impedance: 10 kW or more)

DC ammeter

Full-scale 20 mA (internal impedance: 300 W or less)

Wiring length maximum 10 m

10 INSTALLATION

2INSTALLATION

2.1 Pre-installation instructions

Check that the inverter's input power and the control circuit power are both OFF.

2.2 Installation procedure

Installing the option

The FR-E800 series inverter has only one plug-in option connector.

NOTE

• Ensure the control circuit terminals are wired before installing the plug-in option. They cannot be wired after the plug-in

option is installed.

• When installing the plug-in option, prevent cables being caught between parts. Otherwise the inverter and the option may be

damaged.

CAUTION

• Do not install or remove this product while the inverter power is ON. Doing so may damage the inverter or this product.

• To avoid damage due to static electricity, static electricity in your body must be discharged before you touch the product.

Andere Handbücher für 800 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Electric Wechselrichter Handbücher

Mitsubishi Electric

Mitsubishi Electric FR-A720-0.4K Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-HC2-7.5K Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A8NC Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-F800 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-F802 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-700PJ Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A701 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric A800-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-E720-0.4K Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A7NC E kit-SC Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Merkblatt

Mitsubishi Electric

Mitsubishi Electric FR-A7ND E kit Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric fr-e700 series Merkblatt

Mitsubishi Electric

Mitsubishi Electric FR-D700 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-S540E-0.4K-EC Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-S500 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A5NP Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A500 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PV-PNS04ATL-GER Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A700 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A520-0.4K-NA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A7AR E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

Astrel Group

Astrel Group Power Reducer Kurzanleitung

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung