Mitsubishi Electric FR-A5NP Bedienungsanleitung

FR-A5NP

TRANSISTORIZED INVERTER INSTRUCTION MANUAL

TRANSISTORIZED INVERTER

-INSTRUCTION MANUAL-

TRANSISTORIZED INVERTER

HEAD OFFICE:MITSUBISHI DENKI BLDG MARUNOUCHI TOKYO 100-8310

FR-A5NP

PROFIBUS DP COMMUNICATION OPTION

IB(NA)-0600148E-A (0303) MEE Printed in Japan Specifications subject to change without notice.

Downloaded from ManualsNet.com search engine

A-1

Thank you for choosing the Mitsubishi transistorized inverter option unit.

This instruction manual gives handling information and precautions for use of

this equipment. Incorrect handling might cause an unexpected fault. Before using

the equipment, please read this manual carefully to use the equipment to its

optimum.

1. Electric Shock Prevention

This section is specifically about safety matters

Do not attempt to install, operate, maintain or inspect this product until you

have read through this instruction manual and appended documents carefully

and can use the equipment correctly. Do not use this product until you have a

full knowledge of the equipment, safety information and instructions.

In this instruction manual, the safety instruction levels are classified into

"WARNING" and "CAUTION".

Assumes that incorrect handling may cause

hazardous conditions, resulting in death or

severe injury.

Assumes that incorrect handling may cause

hazardous conditions, resulting in medium or

slight injury, or may cause physical damage only.

Note that the CAUTION level may lead to a serious consequence according to

conditions. Please follow the instructions of both levels because they are

important to personnel safety.

SAFETY INSTRUCTIONS

•

••

•While power is on or when the inverter is running, do not open the front

cover. You may get an electric shock.

•

••

•Do not run the inverter with the front cover removed. Otherwise, you may

access the exposed high-voltage terminals and charging part and get an

electric shock.

•

••

•If power is off, do not remove the front cover except for wiring or periodic

inspection. You may access the charged inverter circuits and get an electric

shock.

•

••

•Before starting wiring or inspection, switch power off, wait for more than 10

minutes, and check for no residual voltage with a tester or the like.

•

••

•Any person who is involved in the wiring or inspection of this equipment

should be fully competent to do the work.

•

••

•Always install the option unit before wiring. Otherwise, you may get an

electric shock or be injured.

•

••

•Handle this option unit with dry hands to prevent an electric shock.

•

••

•Do not subject the cables to scratches, excessive stress, heavy loads or

pinching. Otherwise, you may get an electric shock.

•

••

•While power is on, do not move the station number and baud rate setting

switches. Doing so can cause an electric shock.

WARNING

CAUTION

WARNING

Downloaded from ManualsNet.com search engine

A-2

2. Injury Prevention

3. Additional instructions

Also note the following points to prevent an accidental failure, injury, electric

shock, etc.:

(1) Transportation and mounting

(2) Test operation and adjustment

(3) Usage

(4) Maintenance, inspection and parts replacement

(5) Disposal

(6) General instruction

•

••

•Apply only the voltage specified in the instruction manual to each terminal to

prevent burst, damage, etc.

•

••

•Ensure that the cables are connected to the correct terminals. Otherwise,

burst, damage, etc. may occur.

•

••

•Always make sure that polarity is correct to prevent burst, damage, etc.

•

••

•While power is on or for some time after power-off, do not touch the inverter

as it is hot and you may get burnt.

•

••

•Do not install or operate the option unit if it is damaged or has parts missing.

•

••

•Do not stand or rest heavy objects on the product.

•

••

•Check that the mounting orientation is correct.

•

••

•Prevent screws, metal fragments or other conductive bodies or oil or other

flammable substance from entering the inverter.

•

••

•Before starting operation, confirm and adjust the parameters. A failure to do

so may cause some machines to make unexpected motions.

•

••

•Do not modify the equipment.

•

••

•When parameter clear or all parameter clear is performed, each parameter

returns to the factory setting. Re-set the required parameters before starting

operation.

•

••

•For prevention of damage due to static electricity, touch nearby metal before

touching this product to eliminate static electricity from your body.

•

••

•Do not test the equipment with a megger (measure insulation resistance).

•

••

•Treat as industrial waste.

All illustrations given in this manual may have been drawn with covers or safety

guards removed to provide in-depth description. Before starting operation of

the product, always return the covers and guards into original positions as

specified and operate the equipment in accordance with the manual.

AUTI

WARNING

AUTI

Downloaded from ManualsNet.com search engine

CONTENTS

1. INTRODUCTION 1

2. INSTALLATION 3

2.1 Pre-installation Checks.....................................................................3

2.2 Mounting Procedure .........................................................................3

2.3 Connecting To The Network.............................................................9

2.4 LED Status Indicator.........................................................................9

2.5 Installing MEAU0865.GSD ...............................................................9

3. OPERATION 10

3.1 Operating Modes............................................................................10

3.2 Selecting the Operating Mode........................................................10

3.3 Functions Available in the Operating Modes..................................11

3.4 Input From PROFIBUS to Inverter..................................................11

3.5 Output From Inverter to PROFIBUS...............................................12

3.6 Operation When an Alarm Occurs..................................................13

4. PROFIBUS DEVICE DATA 14

5. INVERTER PROFIBUS DATA WORD DEFINITION 16

5.1 Word 1 (PKE)..................................................................................18

5.2 Word 2 (IND)...................................................................................19

5.3 Word 3 (PWE1)...............................................................................19

5.4 Word 4 (PWE2)...............................................................................19

5.5 Word 5 (ZSW1)...............................................................................20

5.6 Word 6 (HIW)..................................................................................20

6. PARAMETER DEFINITIONS 21

6.1 IND = 0000h, Real-Time Monitor Area ...........................................21

6.2 IND = 01pph, System Environment Variable Area..........................22

6.2.1 IND = 0100h, pp = 00, SEV_I, Block I, SEV Interface.............22

6.2.2 IND = 0101h, pp = 01, SEV_II, Block II, Alarm History............23

6.3 IND = 0200h, Normal Parameter Area............................................24

6.4 IND = 0300h, 900f Parameter Area................................................31

6.5 IND = 0400h, 900% Parameter Area..............................................31

6.6 Time/Program Settings: Frequency (f)

Components (IND = 0600h)............................................................32

6.7 Time/Program Settings: Motor Run Direction (D)

Components (IND = 0700h)............................................................33

6.8 Time/Prog Settings Time (t) Components (IND = 0800h)...............34

Downloaded from ManualsNet.com search engine

7. TROUBLESHOOTING 35

7.1 Inspecting Display On Parameter Unit And Status LED On A5NP.35

8. SPECIFICATIONS 36

Appendix 37

Appendix. A Instruction For MEAU0865.GSD ........................................37

Appendix. B Commonly used PROFIBUS-DP commands .....................38

Appendix. C Network Communication Coordination using

the FR-A5NP PROFIBUS-DP Option Module....................51

Appendix. D Other Option Specific Parameters......................................53

Downloaded from ManualsNet.com search engine

1. INTRODUCTION

GENERAL

The purpose of this manual is to provide general information, installation,

and operation procedures for the FR-A5NP PROFIBUS-DP option, used

with the FR-A500(L)/F500(L) inverter, herein after referred to as the

inverter. Read this manual completely before installing, operating or

servicing the option unit.

This manual is intended for use by qualified personnel. Installation should

only be performed by qualified personnel. You must be able to operate and

program serial devices to use the equipment.

This option unit lets you connect an FR-A500(L)/F500(L) series inverter to

a network adhering to the PROFIBUS-DP communications protocol.

PROFIBUS-DP is the performance-optimized version of PROFIBUS for

time-critical operations.

Illustrations provided in this manual may have covers or safety guards

removed to provide a clear view. Before starting operation of the product

be sure to install covers and guards into the original position.

The following is a list of important features for the option unit

•PROFIBUS

®is a trademark of PROFIBUS User Organization.

• Other company and product names herein are the trademarks and

registered trademarks of their respective owners.

DESCRIPTION

The FR-A5NP option unit consists of two circuit boards. The option unit is

mounted in option port #3 on the inverter unit. The inverter top cover must

be removed to install the option unit. After installation, the top cover is

reinstalled and connection to the PROFIBUS-DP bus is completed through

a connector accessible through the top cover. Two station switches,

mounted on the top printed circuit board, allow the assigning of station

numbers from 0 to 126. A LED status light mounted next to the connector

provides status information on the communication link.

• Data Rates to 12,000,000 bps.

• Up to 126 stations supported on a single network

• Network access to all inverter parameters.

• Certified by PROFIBUS Nutzer Organization in July 1998

Downloaded from ManualsNet.com search engine

INTRODUCTION

FR-A5NP

Front view

Option fixing hole

Mounting

hole

Rear view

connector

Node address switch Operating status

indicator LED

Mounting

hole

Profibus connector

(DB9 pin connector)

SW2

SW1

Mounting

hole

Option fixing hole

Mounting

hole

Downloaded from ManualsNet.com search engine

2. INSTALLATION

Remove the drive cover following the inverter instruction manual and

install the option unit using the following procedure:

2.1 Pre-installation Checks

(1) Check the inverter type.

Use the option unit only with an FR-A500(L)/F500(L) series inverter.

Do not use it with any other series (e.g. A200E, A200, A100, Z and F

series). These other series inverters have a different option connector

to prevent installation.If you force the connector, youmay damage the

inverter as well as the option unit.

(2) Make sure the inverter input power is off. The option unit can be

damaged if installed with the input power on.

(3) Make sure the PLC master (or PROFIBUS-DP master) is properly

grounded before continuing.

2.2 Mounting Procedure

(1) Insert this option unit only into the OPTION PORT# 3 of the inverter.

(2) Carefully insert the connector of the option unit into the connector of

the inverter as shown in Figure 2-1. Use the two mounting holes and

the guide hole to align the bottom board with the matching machine

screw inserts and the plastic guide pin on the inverter. Also be sure to

fit the unit into the option fixing hook (It is available in Aug., 2000).

Make sure that the inverter option is firmly seated in the inverter and

the connector is fully plugged in.

(3) Secure the option unit to the inverter with two mounting screws. If the

screw holes in the option unit do not line up with the inverter mounting

holes, check that the connectors have been fitted correctly.

Hazardous voltage present.

Always isolate power from the inverter and wait 10 minutes until

the bus charge light is off to ensure the charge lamp has gone

out before inserting or removing this option unit or touching the

terminals.

WARNING

Downloaded from ManualsNet.com search engine

INSTALLATION

Figure 2-1. Option Unit Aligned with Option Port #3

(4) Option unit is now mechanically installed as shown is Figure 2-2.

Figure 2-2. Option Unit Installed In Inverter

VSP896M205

3 x 8 mm MACHINE SCREWS WITH

FLAT AND LOCK WASHER

FR-A5NP PLUG IN OPTION

OPTION TO VFD

CONNECTOR

INVERTER

INVERTRE OPTION

PORT #3

MACHINE SCREW INSERTS

TERMINAL

BLOCK

INSTALLED PROFIBUS

OPTION IN PORT #3

CONNECTOR

TO PROFIBUS

INVERTER OPTION

PORT #2

INVERTER OPTION

PORT #1

PARAMETER

UNIT PORT

POWER LAMP

ALARM LAMP

Downloaded from ManualsNet.com search engine

INSTALLATION

(5) Construct a short cable to connect the network to the inverter. On one

end of the cable, install a connector compatible with the network. On

the other end, install a DB9-style male connector. Make sure the cable

can support 12.0 Mbps communications (as specified in the EEIA-RS-

485 standard). This cables connections are shown in Figure 2-3.

Figure 2-3. Connection Cable

REMARKS

Option unit Pins 6 and 5 supply +5Vdc (rated at 100 mA). Connection of Pins 6

and 5 is optional. Pin 4 may not be required for your master. Connection of Pin 4

is also optional. Refer to the user’s manual of your PROFIBUS-DP master.

CONNECTOR SCREWS

PROFIBUS CONNECTOR

(MALE DB-9 NETWORK DEVICE)

PROFIBUS NETWORK CABLE

(TO NEXT NETWORK DEVICE)

PROFIBUS NETWORK CABLE

(FROM NETWORK)

Downloaded from ManualsNet.com search engine

Inhaltsverzeichnis

Andere Mitsubishi Electric Wechselrichter Handbücher

Mitsubishi Electric

Mitsubishi Electric FR-A7NP Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A800 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric A800 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-V500 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-V500 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FREQROL-K Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-E720-0.4K Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A720-0.4K Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-E720-0.1K Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-XCG-K Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric A800-GN Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-V560 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-E8AXY E KIT Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-F500 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-V5NS Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric melpto d series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-V5NE-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A7NC E kit-SC Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-E800 Gebrauchs- und Pflegehandbuch

Mitsubishi Electric

Mitsubishi Electric FR-A7NC E kit-SC Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A720-0.4K Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-POL-H400K Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A806 Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

Astrel Group

Astrel Group Power Reducer Kurzanleitung

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung