Mitsubishi Electric 800 Series Bedienungsanleitung

PRE-OPERATION INSTRUCTIONS 1

INSTALLATION 2

PARAMETER LIST 3

ANALOG OUTPUT 4

DIGITAL OUTPUT 5

INVERTER

Plug-in option

INSTRUCTION MANUAL

FR-A8AY

Analog output function

Digital output function

Safety instructions

Thank you for choosing this Mitsubishi Electric inverter plug-in option.

This Instruction Manual provides handling information and precautions for use of this product. Incorrect handling might cause an unexpected fault. Before

using this product, read this Instruction Manual carefully to ensure proper use.

Please forward this Instruction Manual to the end user.

Electric shock prevention

WARNING

Do not remove the front cover or the wiring cover of the inverter while the inverter power is ON, and do not operate the inverter with the front

cover or the wiring cover removed as the exposed high voltage terminals or the charging part of the circuitry can be touched. Doing so may

cause an electric shock.

Even if power is OFF, do not remove the front cover of the inverter except for wiring or periodic inspection as the inside of the inverter is

charged. Doing so may cause an electric shock.

Before wiring or inspection, check that the display of the inverter operation panel is OFF. Any person who is involved in wiring or inspection

shall wait for 10 minutes or longer after the power supply has been cut off, and check that there are no residual voltage using a digital

multimeter or the like. The capacitor is charged with high voltage for some time after power OFF, and it is dangerous.

Any person who is involved in wiring or inspection of this product shall be fully competent to do the work.

This product must be installed before wiring. Otherwise you may get an electric shock or be injured.

Do not touch this product or handle the cables with wet hands. Doing so may cause an electric shock.

Do not subject the cables to scratches, excessive stress, heavy loads or pinching. Doing so may cause an electric shock.

Do not attempt to install, operate, maintain or inspect this product until you have read this Instruction Manual and supplementary documents

carefully. Do not use this product until you have a full knowledge of this product mechanism, safety information and instructions. In this

Instruction Manual, the safety instruction levels are classified into "WARNING" and "CAUTION".

Incorrect handling may cause hazardous conditions, resulting in death or severe injury.

Incorrect handling may cause hazardous conditions, resulting in medium or slight injury, or may cause only material

damage.

Note that even the level may lead to a serious consequence depending on conditions. Be sure to follow the instructions

of both levels as they are critical to personnel safety.

WARNING

CAUTION

Injury prevention

Additional instructions

The following instructions must be also followed. If this product is handled incorrectly, it may cause unexpected fault, an injury, or an electric shock.

CAUTION

The voltage applied to each terminal must be as specified in the Instruction Manual. Otherwise an explosion or damage may occur.

The cables must be connected to the correct terminals. Otherwise an explosion or damage may occur.

The polarity (+ and -) must be correct. Otherwise an explosion or damage may occur.

While power is ON or for some time after power OFF, do not touch the inverter as it will be extremely hot. Doing so may cause burns.

CAUTION

Transportation and installation

Do not install or operate this product if it is damaged or has parts missing.

Do not stand or place heavy objects on this product.

Ensure the mounting orientation of this product is correct.

Foreign conductive objects must be prevented from entering the inverter. That includes screws and metal fragments or flammable substance

such as oil.

If halogens (including fluorine, chlorine, bromine, and iodine) contained in fumigants for wood packages enter this product, the product may

be damaged. Prevent the entry of fumigant residuals or use an alternative method such as heat disinfection. Note that sterilization or

disinfection of wood packages should be performed before packing the product.

Test operation

Before starting operation, confirm or adjust the parameter settings. Failure to do so may cause some machines to make unexpected

motions.

WARNING

Usage

Do not modify this product.

Do not remove any part which is not instructed to be removed in the Instruction Manuals. Doing so may lead to a failure or damage of this

product.

CAUTION

Usage

As all parameters return to their initial values after Parameter clear or All parameter clear is performed, the parameters must be set again as

required before the operation is started.

To avoid damage to this product due to static electricity, static electricity in your body must be discharged before you touch this product.

Maintenance, inspection and parts replacement

Do not carry out a megger (insulation resistance) test.

Disposal

This product must be treated as industrial waste.

General instruction

For clarity, illustrations in this Instruction Manual may be drawn with covers or safety guards removed. Ensure all covers and safety guards

are properly installed prior to starting operation.

— CONTENTS —

Safety instructions 2

1 PRE-OPERATION INSTRUCTIONS 7

1.1 Unpacking and checking the product............................................................................................................................7

1.1.1 Product confirmation ............................................................................................................................................................. 7

1.2 Component names ..........................................................................................................................................................8

1.3 Specifications ..................................................................................................................................................................9

2 INSTALLATION 10

2.1 Pre-installation instructions .........................................................................................................................................10

2.2 Installation procedure ...................................................................................................................................................11

2.3 Wiring..............................................................................................................................................................................15

3 PARAMETER LIST 19

4 ANALOG OUTPUT 21

4.1 Connection diagram ......................................................................................................................................................21

4.2 Terminals........................................................................................................................................................................22

4.3 Extended analog output function parameter list ........................................................................................................23

4.4 Adjustment procedure ..................................................................................................................................................24

4.4.1 Analog output signal voltage/current switchover (Pr.309) setting ....................................................................................... 24

4.4.2 Meter calibration ................................................................................................................................................................. 26

4.4.3 Setting output signals.......................................................................................................................................................... 28

4.4.4 Analog meter voltage negative output selection (Pr.1019) ................................................................................................. 28

4.4.5 Adjusting the analog signal (Pr.307, Pr.308, Pr.311, Pr.312) ............................................................................................. 29

4.5 Precautions ....................................................................................................................................................................31

5 DIGITAL OUTPUT 32

5.1 Terminals........................................................................................................................................................................32

5.2 Digital output function parameter list..........................................................................................................................33

5.3 Parameter setting ..........................................................................................................................................................33

APPENDIX 35

Appendix 1 Instructions for compliance with the EU Directives ....................................................................................35

Appendix 2 Instructions for EAC .......................................................................................................................................36

Appendix 3 Restricted Use of Hazardous Substances in Electronic and Electrical Products .....................................37

Appendix 4 Referenced Standard (Requirement of Chinese standardized law) ...........................................................38

Appendix 5 Regarding Directive on Waste Electrical and Electronic Equipment .........................................................39

Appendix 6 Compliance with the UK certification scheme .............................................................................................40

REVISIONS 43

PRE-OPERATION INSTRUCTIONS 7

1PRE-OPERATION INSTRUCTIONS

1.1 Unpacking and checking the product

Take the plug-in option out of the package, check the product name, and confirm that the product is as you ordered and intact.

This product is a plug-in option made for the FR-A800/F800 series.

1.1.1 Product confirmation

Check the enclosed items.

Plug-in option: 1 Mounting screw (M3 8 mm): 2

(Refer to page 11.)

Spacer: 2

(Refer to page 11.)

8PRE-OPERATION INSTRUCTIONS

1.2 Component names

Symbol Name Description Refer to

page

a Mounting hole Used to fix this product to the inverter by inserting a mounting screw or a spacer. 11

b Terminal block Used to connect the device to input signals to the inverter, and the device to

receive the signal from the inverter. 15

cSwitch for manufacturer

setting Switch for manufacturer setting. Do not change the initial setting ( ). ─

dBoard mounted option

connector Used to connect this product to the option connector on the inverter. 11

Front view Rear view

(a)

(b)

(d)

(c)

(a)

AM0

AM1

AMC

PRE-OPERATION INSTRUCTIONS 9

1.3 Specifications

Analog output

Digital output

Open collector output specification: permissible load of 24 VDC 0.1 A

Item Voltage output Current output

Output signal 0 to ±10 VDC max (across terminals AM0 to AMC) 0 to 20 mADC (across terminals AM1 to AMC)

Output resolution 3 mV 10 A

Applicable meter

DC voltmeter

Full-scale ±10 V (internal impedance: 10 kor more)

DC ammeter

Full-scale 20 mA (internal impedance: 300 or less)

Wiring length maximum 10 m

10 INSTALLATION

2INSTALLATION

2.1 Pre-installation instructions

Check that the inverter's input power and the control circuit power are both OFF.

CAUTION

• Do not install or remove the plug-in option while the input power is ON. Doing so may damage the inverter or plug-in option.

• To avoid damage due to static electricity, static electricity in your body must be discharged before you touch the product.

Andere Handbücher für 800 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Electric Wechselrichter Handbücher

Mitsubishi Electric

Mitsubishi Electric FR-A820-00046 (0.4K) Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 700 Series Merkblatt

Mitsubishi Electric

Mitsubishi Electric FR-F820-00077 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A8APR Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-700PJ Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric CC-Link IE TSN FR-A8NCG Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 700 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric fr-e700 series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A800 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Stücklistenhandbuch

Mitsubishi Electric

Mitsubishi Electric fr-e700 series Merkblatt

Mitsubishi Electric

Mitsubishi Electric FR-E8TR Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A5AX Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A700 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FREQROL-CS80 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric F700 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-POL-H400K Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-V500 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A8AR Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-ABR-(H)0.4K Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-D740-012SC-EC Merkblatt

Mitsubishi Electric

Mitsubishi Electric FR-A740-00023 Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

Astrel Group

Astrel Group Power Reducer Kurzanleitung

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung