Mitsubishi Electric FR-A7AD Bedienungsanleitung

INSTRUCTION MANUAL

INVERTER

Plug-in option

FR-A7AD

High-speed analog output function

Digital output function INSTALLATION AND WIRING

PARAMETER LIST

HIGH-SPEED ANALOG OUTPUT

PRE-OPERATION

INSTRUCTIONS

DIGITAL OUTPUT

A-1

Thank you for choosing this Mitsubishi Inverter plug-in option.

This Instruction Manual gives handling information and

precautions for use of this equipment. Incorrect handling might

cause an unexpected fault. Before using the equipment, please

read this manual carefully to use the equipment to its optimum.

Please forward this manual to the end user.

1. Electric Shock Prevention

This section is specifically about

safety matters

Do not attempt to install, operate, maintain or inspect this

product until you have read through this Instruction Manual and

appended documents carefully and can use the equipment

correctly. Do not use this product until you have a full

knowledge of the equipment, safety information and

instructions.

In this Instruction Manual, the safety instruction levels are

classified into "WARNING" and "CAUTION".

Incorrect handling may cause

hazardous conditions, resulting in

death or severe injury.

Incorrect handling may cause

hazardous conditions, resulting in

medium or slight injury, or may cause

only material damage.

The level may even lead to a serious

consequence according to conditions. Both instruction levels

must be followed because these are important to personal

safety.

WARNING

CAUTION

SAFETY INSTRUCTIONS

WARNING

•While power is ON or when the inverter is running, do not

open the front cover. You may get an electric shock.

•Do not run the inverter with the front cover or wiring cover

removed. Otherwise, you may access the exposed high-

voltage terminals and charging part and get an electric shock.

•Even if power is OFF, do not remove the front cover except

for wiring or periodic inspection. You may accidentally touch

the charged inverter circuits and get an electric shock.

•Before wiring or inspection, power must be switched OFF. To

confirm that, LED indication of the operation panel must be

checked. (It must be OFF.) Any person who is involved in

wiring or inspection shall wait for at least 10 minutes after the

power supply has been switched OFF and check that there

are no residual voltage using a tester or the like. The

capacitor is charged with high voltage for some time after

power OFF, and it is dangerous.

•Any person who is involved in wiring or inspection of this

equipment shall be fully competent to do the work.

•The plug-in option must be installed before wiring. Otherwise,

you may get an electric shock or be injured.

•Do not touch the plug-in option or handle the cables with wet

hands. Otherwise you may get an electric shock.

•Do not subject the cables to scratches, excessive stress,

heavy loads or pinching. Otherwise you may get an electric

shock.

A-2

2. Injury Prevention

3. Additional Instructions

Also the following points must be noted to prevent an accidental

failure, injury, electric shock, etc.

1) Transportation and mounting

2) Trial run

3) Usage

4) Maintenance, inspection and parts replacement

5) Disposal

6) General instruction

CAUTION

•The voltage applied to each terminal must be the ones

specified in the Instruction Manual. Otherwise burst, damage,

etc. may occur.

•The cables must be connected to the correct terminals.

Otherwise burst, damage, etc. may occur.

•Polarity must be correct. Otherwise burst, damage, etc. may

occur.

•While power is ON or for some time after power-OFF, do not

touch the inverter as they will be extremely hot. Doing so can

cause burns.

CAUTION

•Do not install or operate the plug-in option if it is damaged or

has parts missing.

•Do not stand or rest heavy objects on the product.

•The mounting orientation must be correct.

•Foreign conductive objects must be prevented from entering

the inverter. That includes screws and metal fragments or

other flammable substances such as oil.

CAUTION

•Before starting operation, each parameter must be confirmed

and adjusted. A failure to do so may cause some machines to

make unexpected motions.

WARNING

•Do not modify the equipment.

•Do not perform parts removal which is not instructed in this

manual. Doing so may lead to fault or damage of the inverter.

CAUTION

•

When parameter clear or all parameter clear is performed, the

required parameters must be set again before starting

operations because all parameters return to the initial value.

•Static electricity in your body must be discharged before you

touch the product. Otherwise the product may be damaged.

CAUTION

•Do not test the equipment with a megger (measure insulation

resistance).

CAUTION

•This inverter plug-in option must be treated as industrial

waste.

Many of the diagrams and drawings in this Instruction Manual

show the inverter without a cover or partially open for

explanation. Never operate the inverter in this manner. The

cover must be reinstalled and Instruction manual of the inverter

must be followed when operating the inverter.

— CONTENTS —

1 PRE-OPERATION INSTRUCTIONS 1

1.1 Inverter Model ....................................................................................................................................1

1.2 Unpacking and Product Confirmation .............................................................................................2

1.2.1 Product confirmation.......................................................................................................................................2

1.3 Parts....................................................................................................................................................3

1.4 Specifications.....................................................................................................................................4

2 INSTALLATION AND WIRING 5

2.1 Pre-Installation Instructions .............................................................................................................5

2.2 Installation Procedure .......................................................................................................................6

2.3 Wiring..................................................................................................................................................8

3 PARAMETER LIST 11

4 HIGH-SPEED ANALOG OUTPUT 12

4.1 Wiring Example ................................................................................................................................12

4.2 Terminals ..........................................................................................................................................13

4.3 Calibration procedure......................................................................................................................14

4.3.1 Calibration of voltmeter.................................................................................................................................14

4.3.2 Monitor setting ..............................................................................................................................................17

4.3.3 Scale setting .................................................................................................................................................21

4.3.4 High-speed analog output filter setting .........................................................................................................21

4.4 Instructions ......................................................................................................................................22

5 DIGITAL OUTPUT 23

5.1 Terminals ..........................................................................................................................................23

5.2 Output Signal List ............................................................................................................................24

1PRE-OPERATION INSTRUCTIONS

1.1 Inverter Model

The inverter model numbers of 55K and 75K stated in this Instruction Manual differ according to -NA, -EC,

-CH(T) versions. Refer to the following correspondence table for each inverter model. (Refer to the

Instruction Manual of each inverter for the inverter model.)

For example, "for the 75K or higher" indicates "for the FR-A740-01440-NA or higher" in the case of FR-

A740 of NA version.

NA EC CH

FR-A720-55K FR-A720-02150-NA ⎯⎯

FR-A720-75K FR-A720-02880-NA ⎯⎯

FR-A740-55K FR-A740-01100-NA

(FR-A760-00840-NA) FR-A740-01800-EC FR-A740-55K-CHT

FR-A740-75K FR-A740-01440-NA

(FR-A760-01040-NA) FR-A740-02160-EC FR-A740-75K-CHT

PRE-OPERATION INSTRUCTIONS

1.2 Unpacking and Product Confirmation

Take the plug-in option out of the package, check the product name, and confirm that the product is as you

ordered and intact.

This product is a plug-in option for the FR-A700 series manufactured in December 2011 or later.

Check the SERIAL number specified on the inverter rating plate or package.

zSERIAL number check

Refer to Instruction manual of the inverter for the location of the rating plate.

1.2.1 Product confirmation

Check the enclosed items.

Rating plate example

1 Z {{{{{{ SERIAL

Symbol Year Month Control number

The SERIAL consists of one symbol, two characters indicating production year and month,

and six characters indicating control number.

The last digit of the production year is indicated as the Year, and the Month is indicated by

1 to 9, X (October), Y (November), or Z (December).

Plug-in option

......................................... 1

Mounting screw (M3 ×6mm)

.............. 2 (Refer to page 6.)

Hex-head screw for option

mounting (5.5mm)

............... 1 (Refer to page 6.)

5.5mm

PRE-OPERATION INSTRUCTIONS

1.3 Parts

Front view

Terminal layout

Rear view

Mounting

hole

Mounting hole

Mounting

hole

Terminal

block

Connector

Connect to the inverter

option slot

DD3

DA2

DA3

DA4

DA5

DD0

DD1

DD2

SW1

Switch for manufacturer

setting

Do not change from initially-

set status (OFF: ). (Refer to page 6)

PRE-OPERATION INSTRUCTIONS

1.4 Specifications

(1) Output signals

High-speed analog output (across the terminal 5’s and the terminals DA2 to DA5), 0VDC to ±10VDC

(12-bit output resolution)

Digital output (across the terminal 5’s and the terminals DD0 to DD3), 3V to 6V for HI, 0V to 2V for LOW

(2) Output accuracy (reference value)

±10% of the full-scale output value.

Depends on the output signal type.

(3) Meters used

DC voltmeter Full-scale ±10V (internal impedance 10kΩor more)

Wiring length Maximum 30m

2INSTALLATION AND WIRING

2.1 Pre-Installation Instructions

Make sure that the input power of the inverter is off.

CAUTION

With input power on, do not install or remove the plug-in option. Otherwise, the inverter and

plug-in option may be damaged.

Static electricity in your body must be discharged before you touch the product. Otherwise the

product may be damaged.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Electric Wechselrichter Handbücher

Mitsubishi Electric

Mitsubishi Electric FR-E520 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-F700PJ Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A862-05450-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A800 Merkblatt

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A7AX E kit-SC Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Plus Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A7AR E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-E540 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-F740-00023 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Stücklistenhandbuch

Mitsubishi Electric

Mitsubishi Electric FR-CC2 Merkblatt

Mitsubishi Electric

Mitsubishi Electric A800-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-D700 Series Stücklistenhandbuch

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-D720-070 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-HEL-0.4K Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-E720-600 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-F800 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A800 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-PU07 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-CC2-H315K Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

Astrel Group

Astrel Group Power Reducer Kurzanleitung

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung