Mitsubishi Electric 800 Series Bedienungsanleitung

INSTRUCTION MANUAL

INVERTER

Plug-in option PRE-OPERATION INSTRUCTIONS 1

INSTALLATION AND WIRING 2

ENCODER SPECIFICATIONS AND

PARAMETER SETTINGS 3

ORIENTATION CONTROL 4

ENCODER FEEDBACK CONTROL 5

VECTOR CONTROL 6

FR-A8AP

Orientation control

Encoder feedback control

Vector control

Safety instructions

Thank you for choosing this Mitsubishi Electric inverter plug-in option.

This Instruction Manual provides handling information and precautions for use of this product. Incorrect handling might cause an unexpected fault. Before

using this product, always read this Instruction Manual carefully to use this product correctly.

Please forward this Instruction Manual to the end user.

Electric Shock Prevention

WARNING

While the inverter power is ON, do not open the front cover or the wiring cover. Do not run the inverter with the front cover or the wiring cover

removed. Otherwise you may access the exposed high voltage terminals or the charging part of the circuitry and get an electric shock.

Do not remove the inverter front cover even if the power supply is disconnected. The only exception for this would be when performing wiring

and periodic inspection. You may accidentally touch the charged inverter circuits and get an electric shock.

Before wiring or inspection, LED indication of the inverter unit operation panel must be switched OFF. Any person who is involved in wiring or

inspection shall wait for at least 10 minutes after the power supply has been switched OFF and check that there is no residual voltage using

a tester or the like. For some time after the power-OFF, a high voltage remains in the smoothing capacitor, and it is dangerous.

Any person who is involved in wiring or inspection of this product shall be fully competent to do the work.

The plug-in option must be installed before wiring. Otherwise you may get an electric shock or be injured.

Do not touch the plug-in option or handle the cables with wet hands. Otherwise you may get an electric shock.

Do not subject the cables to scratches, excessive stress, heavy loads or pinching. Otherwise you may get an electric shock.

WARNING Incorrect handling may cause hazardous conditions, resulting in death or severe injury.

Incorrect handling may cause hazardous conditions, resulting in medium or slight injury, or may cause only material

damage.

Do not attempt to install, operate, maintain or inspect the product until you have read through this Instruction Manual and supplementary

documents carefully and can use the equipment correctly. Do not use this product until you have a full knowledge of this product mechanism,

safety information and instructions. In this Instruction Manual, the safety instruction levels are classified into "WARNING" and "CAUTION".

CAUTION

The level may even lead to a serious consequence according to conditions. Both instruction levels must be followed

because these are important to personal safety.

CAUTION

Injury Prevention

Additional Instructions

The following instructions must be also followed. If the product is handled incorrectly, it may cause unexpected fault, an injury, or an electric shock.

CAUTION

The voltage applied to each terminal must be as specified in the Instruction Manual. Otherwise an explosion or damage may occur.

The cables must be connected to the correct terminals. Otherwise an explosion or damage may occur.

The polarity (+ and -) must be correct. Otherwise an explosion or damage may occur.

While power is ON or for some time after power OFF, do not touch the inverter as it will be extremely hot. Touching these devices may cause

burns.

CAUTION

Transportation and installation

Do not install or operate the plug-in option if it is damaged or has parts missing.

Do not stand or rest heavy objects on the product.

Ensure the mounting orientation of this product is correct.

Foreign conductive objects must be prevented from entering the inverter. That includes screws and metal fragments or other flammable

substance such as oil.

If halogens (including fluorine, chlorine, bromine, and iodine) contained in fumigants for wood packages enter this product, the product may

be damaged. Prevent the entry of fumigant residuals or use an alternative method such as heat disinfection. Note that sterilization or

disinfection of wood packages should be performed before packing the product.

Trial run

Before starting operation, confirm or adjust the parameter settings. Failure to do so may cause some machines to make unexpected

motions.

WARNING

Usage

Do not modify the product.

Do not remove any part which is not instructed to be removed in the Instruction Manuals. Doing so may lead to a failure or damage of the

product.

CAUTION

Usage

As all parameters return to their initial values after the Parameter clear or All parameter clear is performed, the parameters must be set again

as required before the operation is started.

Static electricity in your body must be discharged before you touch the product.

Maintenance, inspection and parts replacement

Do not carry out a megger (insulation resistance) test.

Disposal

The inverter must be treated as industrial waste.

General instruction

Many of the diagrams and drawings in this Instruction Manual show the inverter without a cover or partially open for explanation. Never

operate the inverter in this manner. The cover must be reinstalled and the instructions in the Instruction Manual must be followed when

operating the inverter.

— CONTENTS —

Safety instructions 2

1 PRE-OPERATION INSTRUCTIONS 7

1.1 Unpacking and product confirmation............................................................................................................................7

1.2 Component names ..........................................................................................................................................................8

2 INSTALLATION AND WIRING 9

2.1 Pre-installation instructions ...........................................................................................................................................9

2.2 Installation procedure ...................................................................................................................................................10

2.3 Encoder specification / terminating resistor switch setting......................................................................................14

2.4 Wiring..............................................................................................................................................................................17

2.5 Encoder cables dedicated to Mitsubishi Electric motors ..........................................................................................22

2.6 Terminals........................................................................................................................................................................25

3 ENCODER SPECIFICATIONS AND PARAMETER SETTINGS 26

3.1 Encoder ..........................................................................................................................................................................26

4 ORIENTATION CONTROL 31

4.1 Wiring example ..............................................................................................................................................................31

4.2 Terminals........................................................................................................................................................................33

4.3 Specifications ................................................................................................................................................................34

5 ENCODER FEEDBACK CONTROL 35

5.1 Wiring examples ............................................................................................................................................................35

5.2 Specifications ................................................................................................................................................................36

6 VECTOR CONTROL 37

6.1 Wiring examples ............................................................................................................................................................38

6.2 Specifications ................................................................................................................................................................42

APPENDIX 44

Appendix 1 Instructions for compliance with the EU Directives ....................................................................................44

Appendix 2 Instructions for EAC .......................................................................................................................................45

Appendix 3 Restricted Use of Hazardous Substances in Electronic and Electrical Products .....................................46

Appendix 4 Referenced Standard (Requirement of Chinese standardized law) ...........................................................47

Appendix 5 Compliance with the UK certification scheme .............................................................................................48

REVISIONS 51

PRE-OPERATION INSTRUCTIONS 7

1PRE-OPERATION INSTRUCTIONS

1.1 Unpacking and product confirmation

Take the plug-in option out of the package, check the product name, and confirm that the product is as you ordered and intact.

This product is a plug-in option dedicated for the FR-A800 series.

Product confirmation

Check the enclosed items.

NOTE

• Connection diagrams in this Instruction Manual appear with the control logic of the input terminals as sink logic, unless

otherwise specified. (For the control logic, refer to the Instruction Manual(Detailed) of the inverter.)

Plug-in option

.......................................1

Mounting screw (M3 × 8 mm)

........2 (Refer to page 9.)

Spacer

........2 (Refer to page 9)

SW2

SW3

SW1

8PRE-OPERATION INSTRUCTIONS

1.2 Component names

Symbol Name Description Refer to

page

a Mounting hole Fixes the option to the inverter with screws, or installs spacers. 9

b Terminal block Connects to the encoder. 17

c Encoder type selection switch (SW3) Switches the encoder type (differential line driver/ complementary). 14

d CON2 connector Not used. ―

e Terminating resistor selection switch (SW1) Switches ON or OFF the internal terminating resistor. 14

f Switch for manufacturer setting (SW2) Do not change the initially-set status. (Switches 1 and 2 are OFF .) ―

g Board mounted option connector Connects to the option connector of the inverter. 9

h LED for manufacturer check Not used. ―

Front view Rear view

Terminal layout

PA2

PB2

PZ2

PA1

PB1

PZ1

PIN and PO

are not used.

SW2

SW3

SW1

(a) (g)

(a)

(b) (a)

(a)

(e)

(d)

(f)

(c)

(h)

INSTALLATION AND WIRING 9

2INSTALLATION AND WIRING

2.1 Pre-installation instructions

Check that the inverter's input power and the control circuit power are both OFF.

CAUTION

• Do not mount or remove the plug-in option while the input power is ON. Doing so may damage the inverter or plug-in option.

• To avoid damage due to static electricity, static electricity in your body must be discharged before you touch the product.

10 INSTALLATION AND WIRING

2.2 Installation procedure

1. Remove the inverter front cover. (Refer to Chapter 2 of the Instruction Manual (Detailed) of the inverter instructions for

removing the front cover.)

2. Insert two spacers into the mounting holes that will not be used for mounting screws (see the diagrams on page 11 to

identify the holes).

3. Fit the board mounted option connector on this product to the guide of the option connector on the inverter, and insert the

option as far as it goes. (Insert it to the inverter option connector 1 or 2.)

4. Fasten this product to the inverter using the two mounting screws through the holes on either side (tightening torque 0.33

N·m to 0.40 N·m). If the screw holes do not line up, the connector may not be inserted deep enough. Check the

connector.

Spacer

Option connector

on the inverter

Example of installation to connector 1

Andere Handbücher für 800 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Electric Wechselrichter Handbücher

Mitsubishi Electric

Mitsubishi Electric FR-A7NC E kit-SC Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric fr-e720-008 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A700 Series Merkblatt

Mitsubishi Electric

Mitsubishi Electric FR-A862-05450-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A7NP Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A701 Merkblatt

Mitsubishi Electric

Mitsubishi Electric FREQROL HC Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-F800 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-F820-00046 Merkblatt

Mitsubishi Electric

Mitsubishi Electric PV-PNS03ATL-GER Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A800 Stücklistenhandbuch

Mitsubishi Electric

Mitsubishi Electric FR-A5NR Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric DeviceNet FR-E5ND Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric fr-e700 series Installationsanleitung

Mitsubishi Electric

Mitsubishi Electric PV-S4200-IT Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A820-00046 (0.4K) Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A7AP Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Plus Series Stücklistenhandbuch

Mitsubishi Electric

Mitsubishi Electric FR-E720-0.1 K Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-AF700-EC Series Merkblatt

Mitsubishi Electric

Mitsubishi Electric 700 Series Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

Astrel Group

Astrel Group Power Reducer Kurzanleitung

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung