Mitsubishi Electric PLK-G2010R Bedienungsanleitung

INDUSTRIAL SEWING MACHINE

MODEL

PLK-G2010R

TECHNICAL MANUAL

SEWING MACHINE HEAD BASIC

A180E598P02

FOR SAFE USE

Before the installation, operation, and inspection for this product, read the “FOR SAFE USE” and the

technical manuals carefully. Also read the other technical manuals, “Control Unit” and “Operation Panel”

describing some instructions, which are not in this manual, and use the sewing machine properly.

SAFETY INDICATIONS

DANGER

Indicates that incorrect handling may cause hazardous conditions, resulting

in death or severe injury.

CAUTION

Indicates that incorrect handling may cause hazardous conditions, resulting

in medium or slight personal injury or physical damage. Note that CAUTION

level may lead to a serious consequence according to the circumstances.

Always follow the instructions of both levels because they are important to

personal safety.

CAUTION INDICATIONS

No.

Caution indication Description

Precaution for sewing machine operation:

Indicates that removing the safety and operating

the sewing

machine for some other purposes with power-on are prohibited.

Please do not operate the sewing machine without

protective equipment such as a needle guard, an eye guard,

a belt cover or the others.

Please turn off the power switch when threading, changing

a needle and a bobbin, cleaning, and lubricating.

Caution for fingers injury:

Indicates a possibility of fingers (hands) injury in a certain

condition.

Caution for squeezing fingers:

Indicates a possibility of squeezing fingers in a certain condition.

Indication of pulley rotation direction:

Indicates a normal pulley rotation direction of sewing machine.

(For sewing machine with pulley)

From the library of Superior Sewing Machine & Supply LLC - www.supsew.com

SAFETY PRECAUTIONS

DANGER

To prevent from receiving an electric shock, always turn off a power switch and unplug power supply

when opening a control box, and then open after ten minutes passes.

CAUTION

USAGE ENVIRONMENT

Please do not operate the sewing machine under the following conditions.

(1) In the ambient temperature of 35 degrees (95°F) or more than 35 degrees, or the ambient

temperature of 5 degrees or less than 5 degrees (41°F).

(2) In the ambient temperature of 55 degrees (131°F) or more than 55 degrees, or the ambient

temperature of -10 degrees or less than -10 degrees (18°F) during transportation.

(3) In the relative humidity exceeding 85% or less than 45%.

(4) In the open-air place or the location that receives direct sunlight.

(5) In the place near heat sources such as heating devices.

(6) In the atmosphere filled with dust, explosive gas, or corrosive gas.

(7) In the place where the fluctuatio

n in the power voltage of 10% or more than 10%, or the power

voltage of -10% or less than -10% of the fixed power voltage.

(8) In the place where the power source cannot supply enough voltage to keep the motor running.

(9) In the place filled with strong electric noises such as high-frequency welders.

INSTALLATION

(1)

Please have some specialists, who have enough experience for the sewing machine installations,

install the sewing machine.

(2) Please have a qualified electrician perform necessary electric wiring.

(3) Please d

o not operate until the sewing machine is repaired when any damage or fault is found on

the sewing machine at the installation.

(4) Please do not refurbish the sewing machine.

(5) The sewing machine is heavy. For the safety, please make sure to install the sewing machine head

by more than one person.

(6)

When tilting the sewing machine, please stand at the hinge side and hold the sewing machine with

both hands.Also, please lock the caster on the steel stand

(7) When tilting the sewing machine, the work clamp slides toward the hinges. Remember to move the

work clamps fully to the right side of the casting before placing the sewing head in the sewing

position.

(8)

Please lock the caster on the steel stand to prevent the machine from moving before tilting the

sewing machine.

From the library of Superior Sewing Machine & Supply LLC - www.supsew.com

) Please make sure to fit the safety protective equipment (the motor cover or the others) and the

accessory protective equipment (the eye guard) that removed temporarily for installation.

(10) If the table and the steel stand are not MITSUBISHI original, the table and the steel stand have to

be strong enough to withstand the weight and vibration of the sewing machine.

(11) When fitting the caster to the steel stand that are not MITSUBISHI original, the caster with locking

function has to be strong enough to withstand the weight and vibration of the sewing machine.

SEWING

(1) Please make sure to turn the power switch off before installing or replacing needles.

(2) Please pay attention for the fingers not to be injured by the needle point.

(3) Please make sure to turn power switch off before lubricating.

(4) Please pay attention that oil does not get on your skin or in your eyes as it

may cause an

inflammation.

(5) Please make sure to keep oil out of the reach of children who may drink oil by mistake.

(6) Please make sure to turn the power switch off before threading a needle.

(7) Before starting the sewing, please make sure the position and the function of the halt switch.

(8) Please do not touch the operating parts during sewing operation.

(9) It is very dangerous to operate the sewing machine without safety guards (eye guards, belt covers,

link covers, finger guards or the others).

Please make sure to operate the sewing machine with safety guards.

(10) Please make sure to turn the power switch off when stopping the sewing machine temporarily.

ADJUSTMENT

(1) Please make sure to turn the power switch off before adjusting the sewing machine.

(2) If the adjustment is required while the power switch on, do not step on the foot switch by mistake.

(3) Please be careful not to be injured by a sharp part such as the needle and the shuttle hook point.

(4) Please make sure to put the safety guards (eye guards, belt guards, link covers, and finger guards

or the others) back on the initial position after the sewing machine adjustment.

(5) Please make sure to lock the caster on the table when tilting the sewing machine.

From the library of Superior Sewing Machine & Supply LLC - www.supsew.com

CONTENTS

1. STRUCTURE OF THE SEWING MACHINE···································· 1

2. INSTALLATION········································································ 2

2-1. Preparation of the table

··········································································

2-2. Preparation of the steel stand··································································

2-3. Installation of the control box···································································

2-4. Installation of the operation panel·····························································

2-5. Installation of the power switch and foot switch············································

2-6. Installation of the oil pan·········································································

2-7. Installation of the machine head·······························································

2-8. Installation of the stays···········································································

2-9. Installation of the tilting detect switch·························································

2-10. Installation of the eye guard··································································

2-11. Connection of the electric cables····························································

2-12. Installation of the thread stand·······························································

2-13. Connection of the air tube ····································································

3. LUBRICATION········································································· 9

4. INITIAL SETTING OF THE CONTROL BOX··································· 9

From the library of Superior Sewing Machine & Supply LLC - www.supsew.com

1. STRUCTURE OF THE SEWING MACHINE

PLK-G2010R electronic pattern sewing machine consists of the following main parts.

<1>: Sewing machine head <2>: Main shaft motor <3>: Halt switch <4>: Control box

<5>: Operation panel <6>: Work holder foot switch <7>: Start foot switch <8>:Gas spring

<9>: Steel stand <10>: Thread stand <11>: Work holder pedal (Option)

<1>

<2>

<4>

<5>

<7>

<9>

<8>

<10>

<6>

<11>

<3>

- 1 -

From the library of Superior Sewing Machine & Supply LLC - www.supsew.com

2. INSTALLATION

CAUTION

(1)

Please have some specialists, who have enough experience for the sewing machine installations,

install the sewing machine.

(2) Please have a qualified electrician perform necessary electric wiring.

(3)

Please do not operate until the sewing machine is repaired when any damage or fault is found on the

sewing machine at the installation.

(4) Please do not refurbish the sewing machine.

(5)

If the table and the steel stand are not MITSUBISHI original, the table and the steel stand have to be

strong enough to withstand the weight and vibration of the sewing machine.

(6) When fitting the caster to the steel stand that

are not MITSUBISHI original, the caster with locking

function has to be strong enough to withstand the weight and vibration of the sewing machine.

2-1. Preparation of the table

(1) If the table is not MITSUBISHI original, the thickness of the table is required to have 40mm and that is

strong enough to withstand the weight and vibration of the sewing machine.

(2) Manufacture the table as shown on the figure below.

- 2 -

From the library of Superior Sewing Machine & Supply LLC - www.supsew.com

2-2. Preparation of the steel stand

(1) If the steel stand is not MITSUBISHI original, please refer

to the dimensions shown on the figure at the right.

(2) When fitting the caster to the steel stand, the steel stand

has to be strong enough to withstand the weight and vibration

of the sewing machine.

(3) If the steel stand is MITSUBISHI PLK-G2516R original,

assemble the steel stand with the assembling instructions

enclosed in the packing.

2-3. Installation of the control box

Install the control box with the instructions in the paragraph “[3] Installation” in the CONTROL UNIT

technical manual.

* For connector location see page 7, Section 3-10 of this catalog.

2-4. Installation of the operation panel

Connect the operation panel PLK-G-PAL with the CON Aon the rear of the control box.

* See page 7 for the location.

2-5. Installation of the power switch and foot switch

(1) Mount the power switch (No.1) with the wood screw (No.2) at the position as shown on the figure.

(2) Hook up the connector (No.3) of the power switch to the control box CON B.

(3) Attach the power plug (No.5) to the incoming electrical cable (No.4).

(4) Fix the electric cables with the staples (No.6) to prevent the cables from hanging down.

(5) Hook up the connector (No.8) of the foot switch (No.7) to the control box CON H.

(6) As for the control box connector, refer to the instructions in the paragraph “3-10.Connection of the

electric cables” in this manual.

[Notice] Power plug (No.5) is not included in accessory box.

<1>: Power switch

<2>: Wood screw

<3>: Power switch connector

<4>: Electrical cable

<5>: Power plug

<6>: Staple (six staples)

<7>: Foot switch

<8>: Foot switch connector

<1>

<2>

<3>

<6>

<8>

<5>

<7>

<4>

- 3 -

From the library of Superior Sewing Machine & Supply LLC - www.supsew.com

2-6. Installation of the oil pan

(1) Remove the oil pan A (No.1) from the accessory box then, set the oil bottle (No.2) to the oil pan A

(No.1).

(2) Put the oil pan at the position shown on the figure then, fix the oil pan with staples (No.3).

(3) Set the damper cushions (No.4) to the table.

2-7. Installation of the machine head

CAUTION

(1) The sewing machine

is heavy. For the safety, please make sure to install the sewing machine head by

more than one person.

(2)

When tilting the sewing machine, please stand at the hinge side and hold the sewing machine with

both hands.Also, please lock the caster on the steel stand.

(3) When tilting the sewing machine, the work clamp slides toward the hinges. Remember to move the

work clamps fully to the right side of the casting before placing the sewing head in the sewing

position.

(1) Put the machine head carefully on the damper cushion.

(2) Insert the hinge shafts (No.1) into the hole on the machine then, fix it to the machine with set screws

(No.2).

(3) Fit the hinge rubbers (No.4) and the support plates (No.5) into the holes of the hinges (No.3) then, set

the hinges to the hinge shafts.

(4) Fit the screw holes of the hinges (No.3) to the bolt setting holes then, fix the machine with the socket

bolts (No.6) and the flat washers (No.7).

(5) Fix the head rest (No.8) with safety socket bolts (No.9).

<1>: Oil pan

<2>: Oil bottle

<3>: Staple (four staples)

<4>: Damper cushion

(six cushions)

<3> <1>

<2>

<4>

Upside

<4>

- 4 -

From the library of Superior Sewing Machine & Supply LLC - www.supsew.com

2-8. Installation of the stays

(1) Remove the bracket (No.3) after installing the machine head.

(2) Fix the stay (right) (No.1) with the socket bolts (No.4), the flat washers (No.5), and the screws (No.6).

(3) Attach the stay (left) (No.2) to the other side by the same procedure.

<1>: Hinge shaft (two shafts)

<2>: Set screw (two screws)

<3>: Hinge (two hinges)

<4>: Hinge rubber (two rubbers)

<5>: Support plate (two plates)

<6>: Socket bolt (four bolts)

<7>: Flat washer (four washers)

<8>: Head rest

<9>: Safety socket bolt (four bolts)

<3>

<5>

<7>

<6>

<1>

<2>

<8>

<9>

<4>

<1>: Stay (right)

<2>: Stay (left)

<3>: Bracket

<4>: Socket bolt (two bolts)

<5>: Flat washer (2 washers)

<6>: Screw (3 screws)

<1>

<5>

<4>

<6>

<3>

<2>

- 5 -

From the library of Superior Sewing Machine & Supply LLC - www.supsew.com

Andere Handbücher für PLK-G2010R

Inhaltsverzeichnis

Andere Mitsubishi Electric Nähmaschine Handbücher

Mitsubishi Electric

Mitsubishi Electric PLK-E SERIES Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-G2008H Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MP-J25-AD Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-J6040R3 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-J10050R3 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-J6040 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-G2008H-BTRM Technisches Handbuch

Mitsubishi Electric

Mitsubishi Electric PLK-G4030R Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-J4040R Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-J10050RH Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric LT2-2220-B0B Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-G-CU-20 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric LY2-3310-B1T Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-G5050 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-J2516-YU Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-J-CU-20 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-G2516 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric XC-G500-Y Handbuch

Mitsubishi Electric

Mitsubishi Electric PLK-G3040R Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-G2516R Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MP-J-PP Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric LY2-3750-B1T Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-J Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-G10050R Bedienungsanleitung

Beliebte Nähmaschine Handbücher anderer Marken

Riccar

Riccar RL634DE Bedienungsanleitung

Pfaff

Pfaff 3307-1 SERIES Bedienungsanleitung

Siruba

Siruba C007JP Bedienungsanleitung

Husqvarna Viking

Husqvarna Viking Designer SE Bedienungsanleitung

Singer

Singer 148-5 Bedienungsanleitung

IKEA

IKEA SY Bedienungsanleitung

Pfaff

Pfaff 571 Bedienungsanleitung

Singer

Singer 15-91 Bedienungsanleitung

Brother

Brother BB370 Bedienungsanleitung

Pegasus

Pegasus WT100 Series Bedienungsanleitung

Reliable

Reliable 7100DB Bedienungsanleitung

Pfaff

Pfaff 937 Bedienungsanleitung

Singer

Singer 6038 Bedienungsanleitung

Singer

Singer 413K Bedienungsanleitung

Pfaff

Pfaff 1471 E1 Bedienungsanleitung

Kenmore

Kenmore 16677 - Serger Sewing Machine Bedienungsanleitung

HIGHLEAD

HIGHLEAD GC2008-M Bedienungsanleitung

Singer

Singer 400W4 Bedienungsanleitung