Mitsubishi MELSEC Q Series Bedienungsanleitung

A- 1

SAFETY PRECAUTIONS

(Always read these instructions before using this product.)

Before using this product, please read this manual and the relevant manuals introduced in this manual

carefully and pay full attention to safety to handle the product correctly.

The instructions given in this manual are concerned with this product. For the safety instructions of the

programmable controller system, please read the CPU module user's manual.

In this manual, the safety instructions are ranked as "DANGER" and "CAUTION".

Note that the CAUTION level may lead to a serious consequence according to the circumstances.

Always follow the instructions of both levels because they are important to personal safety.

Please keep this manual in a safe place for future reference and also pass this manual on to the end user.

[Design Precautions]

DANGER

Provide a safety circuit outside the C Controller module to ensure that the entire system will operate

safely even if an external power failure or C Controller module failure occurs.

Failure to do so could result in accidents due to erroneous output or operation.

(1) For an emergency stop circuit, protection circuit and interlock circuit that is designed for

incompatible actions such as forward/reverse rotation or for damage prevention such as the

upper/lower limit setting in positioning, any of them must be provided outside the C Controller

module.

(2) When the C Controller module detects the following conditions, it will disable the output (Y) from

the user program and writing to buffer memory in the case of both (a) and (b) and turn off all

outputs for (b).

Whether to hold or clear all the outputs is set by a parameter.

(a) The overcurrent protector or overvoltage protector of the power supply module is activated.

(b) An error such as a watchdog timer error is detected by the self-diagnostic function of the C

Controller module.

If an error occurs in I/O control parts and the C Controller module cannot detect the error, all the

outputs may turn ON.

Provide a fail-safe circuit or a preventive mechanism outside the C Controller module so that

machines will operate safely in such a case. For fail-safe circuit examples, refer to "Chapter 5

SETTINGS AND PROCEDURES BEFORE OPERATION" in this manual.

(3) Output could be left on or off when there is a fault in an output module relay or transistor.

So build an external monitoring circuit that will monitor any output signal that could cause serious

accidents.

DANGER Indicates that incorrect handling may cause hazardous conditions,

resulting in death or severe injury.

CAUTION Indicates that incorrect handling may cause hazardous conditions,

resulting in minor or moderate personal injury or physical damage.

A- 2

[Design Precautions]

DANGER

If load current more than the rating or overcurrent due to a short circuit in the load has flowed in the

output module for a long time, it may cause a fire and smoke. Provide an external safety device

such as a fuse.

Create the circuit so that the external power supply will turn on after the C Controller system is

powered on.

Turning on the external power supply first could result in accidents due to erroneous output or

operation.

For each station's operating status in the event of a each station error, refer to the corresponding

each station manual.

Not doing so could result in erroneous output or operation.

When controlling a running C Controller module (data modification) by connecting a personal

computer to the C Controller module, create an interlock circuit on user programs so that the whole

system functions safely all the time.

This must be also done when performing any other controls (e.g. operating status change (status

control)) or operations instructed from the computer.

In these controls, especially the one performed from an external device to a C Controller module in a

remote location, some C Controller side problem may not be resolved immediately due to failure of

data communications.

To prevent this, create an interlock circuit on user programs and establish corrective procedures for

communication failure between the external device and the C Controller module.

When setting up the system, do not allow any empty slot on the base unit.

If any slot is left empty, be sure to use a blank cover (QG60).

Otherwise, in the short circuit test or when an overcurrent or overvoltage is accidentally applied to

the external I/O section, internal parts of the module may be flied.

CAUTION

Do not install the control wires or communication cables together with the main circuit or power

wires, or bring them close to each other.

Keep a distance of 100 mm (3.94 inch) or more between them.

Not doing so could result in malfunctions due to noise.

When controlling a lamp, heater or solenoid valve using an output module, large current

(approximately ten times greater than in normal conditions) may flow when the output is turned ON

from OFF.

Take preventive measures such as replacing the module with the one having sufficient rated current.

A- 3

[Installation Precautions]

CAUTION

Use the C Controller module in an environment that meets the general specifications shown in this

manual.

Using this C Controller module in an environment outside the range of the general specifications

could result in an electric shock, fire, erroneous operation, and damage to or deterioration of the

product.

While pressing the installation lever located at the bottom of module, insert the module fixing tab into

the fixing hole in the base unit until it stops. Then, mount the module with the fixing hole as a

supporting point.

Incorrect loading of the module can cause a malfunction, failure or drop.

When using the C Controller module in the environment of frequent vibrations, tighten the module

with screws.

Tighten the screws in the specified torque range.

Undertightening can cause a drop, short circuit or malfunction.

Overtightening can cause a drop, short circuit or malfunction due to damage to the screw or module.

Connect extension cables to the connectors of the base unit and the extension module correctly.

After connection, check them for looseness.

Poor contact could cause an input or output failure.

Be sure to set the CompactFlashTM card by pressing it into the CompactFlashTM card slot.

Confirm it is completely set.

Poor contact may lead to malfunctions.

Completely turn off the externally supplied power used in the system before mounting or removing

the module.

Not doing so could result in damage to the product.

Do not directly touch the module's conductive parts.

Doing so could cause an operation failure or give damage to the module.

A- 4

[Wiring Precautions]

DANGER

Completely turn off the externally supplied power used in the system when wiring.

Failure to do so could result in an electric shock or damage to the product.

Before energizing or operating the system after wiring, be sure attach the terminal cover supplied

with the product.

Failure to do so could result in an electric shock.

CAUTION

Be sure to ground the FG and LG terminals to the protective ground conductor.

Not doing so could result in an electric shock or erroneous operation.

Prevent foreign matter such as dust or wiring debris from entering the module.

Failure to do so could cause fires, damage, or erroneous operation.

When wiring, check the rated voltage and terminal layout.

Connecting a power supply of a different voltage rating or incorrect wiring may result in a fire or

failure.

Connect the Ethernet and/or RS-232 cables to the corresponding connectors of the C Controller

module properly.

Tighten the terminal screws with the specified torque.

If the terminal screws are loose, it could result in short circuits, fire or erroneous operation.

Tightening them too much may cause damages to the screws and/or the module, resulting in fallout,

short circuits or malfunction.

Be sure to place the communication and power cables into a duct or fasten them using clamps.

Failure to do so may damage the module or cables by pulling a dangling cable inadvertently or cause

the module to malfunction due to poor contact.

When disconnecting the communication and power cables from the module, do not pull a cable part

by hand.

For a cable with connectors, hold the connector by hand and disconnect it from the module.

Loosen screws on the part connected to the module before disconnecting a cable.

Pulling a cable that is still connected to the module may cause a malfunction or damage the module

or the cable.

Do not connect the outputs of multiple power supply modules in parallel.

Doing so can heat the power supply modules, causing fires or failures.

Crimp, pressure weld, or solder external connectors properly with the tools specified by the maker.

Refer to the I/O Module User's Manual for the tools.

Incomplete connection can cause a short circuit, fire or failure.

A- 5

[Startup and Maintenance Precautions]

DANGER

Do not touch the terminals while power is on.

Doing so may cause an electric shock.

Correctly connect the battery.

Also, do not charge, disassemble, heat, place in fire, short circuit, or solder the battery.

Mishandling of the battery can cause overheating or cracks which could result in injury and/or fires.

Be sure to shut off all phases of the external power supply before retightening the terminal screws

and module fixing screws or cleaning.

Failure to do so may result in an electric shock.

If a terminal screw is loose, it may cause a short circuit or malfunction.

If too tight, it may cause damage to the screws and/or module, resulting in an accidental drop of the

module, short circuit or malfunctions.

When controlling a running C Controller module (data modification) by connecting a personal

computer to the C Controller module, create an interlock circuit on user programs so that the whole

system functions safely all the time.

This must be also done when performing any other controls (e.g. operating status change (status

control)) or operations instructed from the computer.

In these controls, especially the one performed from an external device to a C Controller module in a

remote location, some C Controller side problem may not be resolved immediately due to failure of

data communications.

To prevent this, create an interlock circuit on user programs and establish corrective

procedures for communication failure between the external device and the C Controller module.

A- 6

[Startup and Maintenance Precautions]

CAUTION

Do not disassemble or modify the modules.

Doing so could cause malfunction, erroneous operation, injury, or fire.

Perform online operations connecting peripheral devices to the running C Controller module

(especially program modification, forced output, and operation status change) after reading the

manual carefully and fully ensuring the safety.

Operation mistakes could cause mechanical damage or accidents.

Completely turn off the externally supplied power used in the system before mounting or removing

the module.

Not doing so could result in module failure or malfunction.

Do not mount/remove the module onto/from the base unit more than 50 times

(IEC 61131-2 compliant), after the first use of the product.

Doing so may cause malfunction.

Use any radio communication device such as a cellular phone or a PHS phone more than 25cm

(9.85 inch) away in all directions of the C Controller module.

Not doing so can cause malfunction.

Do not drop or give an impact to the battery installed to the module.

Doing so may damage the battery, causing the battery fluid to leak inside the battery.

If the battery is dropped or given an impact, dispose of it without using.

Before handling the module, touch a grounded metal object to discharge the static electricity from

the human body.

Not doing so can cause the module to fail or malfunction.

A- 7

[Disposal Precautions]

[Transportation Precautions]

CAUTION

When disposing of this product, treat it as industrial waste.

When disposing of batteries, separate them from other wastes according to the local regulations.

(For details of the battery directive in EU member states, refer to Appendix 4.)

CAUTION

When transporting lithium batteries, make sure to treat them based on the transport regulations.

(Refer to Appendix 3 for details of the relevant models.)

A- 8

REVISIONS

*The manual number is given on the bottom left of the back cover.

Print Date *Manual Number Revision

Jun., 2005 SH(NA)-080555ENG-A First edition

Oct., 2005 SH(NA)-080555ENG-B

Precautions for programming, HOW THIS MANUAL IS ORGANIZED,

GENERIC TERMS AND ABBREVIATIONS USED IN THIS MANUAL, Chapter 1,

Section 2.3, 2.4, Section 4.9, 4.12 to 4.14, Section 5.2, 5.6, 5.7.1, 5.7.3, 5.9.1,

Section 6.6.2, Section 9.5.1, Section 10.2.6, 10.3.10, Section 12.1.1, 12.1.4 to

12.1.6, 12.3, Section 13.1, 13.2, 13.4.2, 13.6, 13.7, Section 14.2, 14.3.1, 14.3.2,

Section 15.1, Section 18.2.8, 18.2.10, 18.2.11, 18.3, 18.4.2, INDEX

Section 9.5.10, Appendix 5

Oct., 2006 SH(NA)-080555ENG-C

SAFETY PRECAUTIONS, GENERIC TERMS AND ABBREVIATIONS,

Section 1.1, 2.2.1, 2.2.2, 2.3, 3.3, 4.4.5, 4.5.3, 4.6, 4.7, 5.7.3, 5.7.4, 9.1.6, 9.2,

9.2.1, 9.2.2, 9.2.5, 9.2.7 to 9.2.9, 9.2.11, 9.3, 9.3.2, 9.3.5, 9.3.6, 9.3.8, 9.4, 9.4.2,

9.4.4, 9.4.6 to 9.4.8, 9.5, 9.5.4, 10.2.1, 10.3.11, 10.3.12, 11.1, 12.2.1, 14.2,

17.2.3, 17.2.4, 18.1, 18.2.1 to 18.2.3, 18.2.5 to 18.2.7, 18.2.9, 18.2.10, 18.2.12,

18.3, 18.4.1, 18.4.3, Appendix 1, 2, 5, INDEX

Section 4.3.1, Appendix 6

Nov., 2006 SH(NA)-080555ENG-D

Section 9.2.6, 18.4.1, 18.4.3

Feb., 2007 SH(NA)-080555ENG-E

“PLC” was changed to “programmable controller”.

OPERATING PRECAUTIONS, Section 2.2.2, 10.3.12

Apr., 2007 SH(NA)-080555ENG-F

SAFETY PRECAUTIONS, GENERIC TERMS AND ABBREVIATIONS,

Section 1.1, 2.1.4, 2.1.5, 2.2.1, 2.2.2, 4.1, 4.4, 4.4.1, 4.4.2, 4.4.5, 4.5.1, 4.14,

9.4.7, 10.1, 10.2.5, 11.1, 12.1.1, 12.1.4 to 12.1.6, 14.2, 14.3.3, 18.3,

Appendix 5, 6

Oct., 2007 SH(NA)-080555ENG-G

SAFETY PRECAUTIONS, OPERATING PRECAUTIONS, HOW THIS MANUAL

IS ORGANIZED, GENERIC TERMS AND ABBREVIATIONS, PACKING LIST,

Section 2.1.4, 2.2.1, 2.2.2, 2.3, 3.2, 3.3, 4.5, 4.5.3, 4.5.4, 5.1, 5.2, 5.4, 5.7.4,

5.8.3, 5.10, 5.11.2, 8.1, 8.4, 9.1.3, 9.3.6, 9.4.2, 9.4.7, 10.2.3, 10.2.5, 11.1, 12.2.1,

12.3, 13.1, 14.5, 18.2, 18.4.1, 18.4.3, Appendix 1

Section 18.2.14

Modifications

Additions

Modifications

Additions

Modifications

Change of a term

Modifications

Additions

Andere Handbücher für MELSEC Q Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Steuereinheit Handbücher

Mitsubishi

Mitsubishi MELSEC-F FX2N Series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC Q Series Bedienungsanleitung

Mitsubishi

Mitsubishi FX1N-5DM Bedienungsanleitung

Mitsubishi

Mitsubishi MELDAS MDS-C1 Bedienungsanleitung

Mitsubishi

Mitsubishi M800S series Einrichtungshandbuch

Mitsubishi

Mitsubishi MELSEC L Series Bedienungsanleitung

Mitsubishi

Mitsubishi AJ65SBT2B-64AD Bedienungsanleitung

Mitsubishi

Mitsubishi Q62HLC Bedienungsanleitung

Mitsubishi

Mitsubishi Q Series Bedienungsanleitung

Mitsubishi

Mitsubishi QD75M1 Bedienungsanleitung

Mitsubishi

Mitsubishi MELSECNET/10 A1SJ72QLP25 Bedienungsanleitung

Mitsubishi

Mitsubishi L Series Bedienungsanleitung

Mitsubishi

Mitsubishi GOT MELSEC 800 Series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC A1S64AD Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-Q Q06CCPU-V-B Bedienungsanleitung

Mitsubishi

Mitsubishi QJ72LP25-25 Gebrauchsanweisung

Mitsubishi

Mitsubishi A8GT-50KBF Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-A A1SJ71PB93D Bedienungsanleitung

Mitsubishi

Mitsubishi Melsec-A AJ65SBT Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-F FX-1GM Montageanleitung

Mitsubishi

Mitsubishi FX2N Bedienungsanleitung

Mitsubishi

Mitsubishi QJ71NT11B Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-L Series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC System Q Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung