Mitsubishi FX1N-14MR-ES/UL Bedienungsanleitung

HARDWARE MANUAL

FX1N SERIES PROGRAMMABLE CONTROLLERS

FX1N Series Programmable Controllers

Foreword

• This manual contains text, diagrams and explanations which will guide the reader in the correct installation

and operation of the FX1N Series Programmable Controllers. It should be read and understood before

attempting to install or use the unit.

• Further information can be found in the FX Series Programming Manual II.

• If in doubt at any stage of the installation of an FX1N Series Programmable Controller always consult a

professional electrical engineer who is qualified and trained to the local and national standards which apply to

the installation site.

• If in doubt about the operation or use of FX1N Series Programmable Controller please consult the nearest

Mitsubishi Electric distributor.

• This manual is subject to change without notice.

FX1N SERIES PROGRAMMING CAUTION

Thank you for buying The Mitsubishi FX1N series controller.

Please note the following.

Notes: Block Move instruction

Applicable PLC: FX1N Ver 1.00-2.10

Applicable instructions: BMOV, BMOVP(FNC15)

If the file register parameter setting and the registers D8000-D8225 are used as the

destination devices for the BMOV(BMOVP) instruction, program steps or file register data may

be lost or damaged. All other data registers can be used safely for BMOV(BMOVP) instruction

destination registers.

Program example

BMOV D8140 K2

(S·) (D·) n

M8002

DMOV D8140

(S·) (D·)

M8002

Problem OK

D D

FX1N Series Programmable Controllers

Hardware Manual

This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent

licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial

property rights which may occur as a result of using the contents noted in this manual.

FX1N Series Programmable Controllers

Manual number : JY992D89301

Manual revision : L

Date : May 2006

FX1N Series Programmable Controllers

Guidelines for the safety of the user and protection of the FX1N.

This manual provides information for the installation and use of the FX1N. The manual has

been written to be used by trained and competent personnel. The definition of such a person

or persons is as follows;

a) Any engineer who is responsible for the planning, design and construction of automatic

equipment using the product associated with this manual should be of a competent

nature, (trained and qualified to the local and national standards required to fulfill that

role). These engineers should be fully aware of all aspects of safety with regards to

automated equipment.

b) Any commissioning or service engineer must be of a competent nature, trained and

qualified to the local and national standards required to fulfill that job. These engineers

should also be trained in the use and maintenance of the completed product. This

includes being completely familiar with all associated documentation for the said product.

All maintenance should be carried out in accordance with established safety practices.

c) All operators of the completed equipment (see Note) should be trained to use that

product in a safe manner in compliance to established safety practices. The operators

should also be familiar with documentation which is associated with the operation of the

completed equipment.

Note : The term ‘completed equipment’ refers to a third party constructed device which

contains or uses the product associated with this manual.

FX1N Series Programmable Controllers

iii

Note’s on the symbols used in this manual

At various times through out this manual certain symbols will be used to highlight points of

information which are intended to ensure the users personal safety and protect the integrity of

the equipment. Whenever any of the following symbols are encountered, its associated note

must be read and understood. Each of the symbols used will now be listed with a brief

description of its meaning.

Hardware warnings

1) Indicates that the identified danger WILL cause physical and property damage.

2) Indicates that the identified danger could POSSIBLY cause physical and property damage.

3) Indicates a point of further interest or further explanation.

Software warning

1) Indicates special care must be taken when using this element of software.

2) Indicates a special point which the user of the associate software element should be aware

of.

3) Indicates a point of interest or further explanation.

FX1N Series Programmable Controllers

• Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential

damage that may arise as a result of the installation or use of this equipment.

• All examples and diagrams shown in this manual are intended only as an aid to understanding the

text, not to guarantee operation. Mitsubishi Electric will accept no responsibility for actual use of the

product based on these illustrative examples.

• Please contact a Mitsubishi Electric distributor for more information concerning applications in life

critical situations or high reliability.

FX1N Series Programmable Controllers

Note Concerning the CE Marking

This document does not guarantee that a mechanical system including this product will comply

with the following standards. Compliance to EMC directive and LVD directive of the entire

mechanical system should be checked by the user / manufacturer.

For more details please contact the local Mitsubishi Electric sales site.

EMC

The following products have shown compliance through direct testing (of the identified

standards below) and design analysis (through the creation of a technical construction file) to

the European Directive for Electromagnetic Compatibility (89/336/EEC) when used as directed

by the appropriate documentation.

Refer to a manual or related material of each product other than the following.

Type : Programmable Controller (Open Type Equipment)

Models : MELSEC FX1N series manufactured

from March 1st, 2000 FX1N-232-BD FX1N-485-BD FX1N-422-BD

FX1N-8AV-BD FX1N-CNV-IF FX1N-5DM

FX1N-EEPROM-8L

from June 1st, 2000 FX1N-MR-ES/UL

from December 1st, 2000 FX1N-MR-DS FX1N-MT-DSS

Where  indicates:14,24,40,60

FX1N Series Programmable Controllers

from June 1st, 2001 FX1N-4EX-BD FX1N-2EYT-BD FX1N-2AD-BD

FX1N-1DA-BD

from July 1st, 2001 FX1N-MT-ESS/UL Where  indicates:14,24,40,60

Models : MELSEC FX0N series manufactured

from November 1st, 1995 FX0N-40ER-ES, FX0N-8EX-ES, FX0N-8EYR-ES,

FX0N-8EYT-ESS

from February 1st, 1996 FX0N-8ER-ES, FX0N-16EX-ES, FX0N-16EYR-ES,

FX0N-16EYT-ESS

from April 1st, 1996 FX0N-8ER-ES/UL, FX0N-16EX-ES/UL,FX0N-16EYR-ES/UL,

FX0N-16EYT-ESS/UL

from May 1st, 1996 FX0N-40ER-DS, FX0N-40ET-DSS

FX0N-232ADP, FX0N-485ADP

from July 1st, 1996 Harmonized Products

FX0N-40ER-ES/UL, FX0N-8EX-ES/UL,FX0N-8EYR-ES/UL,

FX0N-8EYT-ESS/UL

Models : MELSEC FX2NC series manufactured

from October 1st, 2002 FX2NC-232ADP FX2NC-485ADP

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Controller Handbücher

Mitsubishi

Mitsubishi MELSEC-A A1SD71-S2 Bedienungsanleitung

Mitsubishi

Mitsubishi FX0S Series Bedienungsanleitung

Mitsubishi

Mitsubishi FX3UC Series Bedienungsanleitung

Mitsubishi

Mitsubishi FX Series Bedienungsanleitung

Mitsubishi

Mitsubishi FX3U-32DP Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC Q Series Bedienungsanleitung

Mitsubishi

Mitsubishi FX3U-4AD-PNK-ADP Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-A series Bedienungsanleitung

Mitsubishi

Mitsubishi QD62-H01 Bedienungsanleitung

Mitsubishi

Mitsubishi FX3U-20SSC-H Bedienungsanleitung

Mitsubishi

Mitsubishi FX3U Series Bedienungsanleitung

Mitsubishi

Mitsubishi FX2N series Bedienungsanleitung

Mitsubishi

Mitsubishi FX3U-32DP Bedienungsanleitung

Mitsubishi

Mitsubishi FX2N-485-BD Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-AnS Series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-F FX3U-4AD-TC-ADP Bedienungsanleitung

Mitsubishi

Mitsubishi A64BTL Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC Q Series Bedienungsanleitung

Mitsubishi

Mitsubishi QS03NB-U-HW Bedienungsanleitung

Mitsubishi

Mitsubishi AJ65SBT2B-64RD3 Bedienungsanleitung

Mitsubishi

Mitsubishi FX3U Series Bedienungsanleitung

Mitsubishi

Mitsubishi QCPU Betriebsanleitung

Mitsubishi

Mitsubishi MELSEC-A AJ71PT3 Bedienungsanleitung

Mitsubishi

Mitsubishi FX-30P Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung