Mitsubishi FX2NC-485ADP Bedienungsanleitung

Mitsubishi Electric Corporation

FX Series Computer Link

Driver

1 System Configuration.......................................................................................................3

2 Selection of External Device............................................................................................7

3 Example of Communication Setting.................................................................................8

4 Setup Items....................................................................................................................15

5 Cable Diagram...............................................................................................................20

6 Supported Device...........................................................................................................35

7 Device Code and Address Code....................................................................................37

8 Error Messages..............................................................................................................38

FX Series Computer Link Driver

GP-Pro EX Device/PLC Connection Manual 2

Introduction

This manual describes how to connect Display and External Device (target PLC).

In this manual, the connection procedure will be described by following the below sections:

1System Configuration

This section shows the types of External

Device which can be connected and SIO

type.

)"1 System Configuration" (page 3)

2Selection of External Device

Select a model (series) of the External

Device to be connected and connection

method

)"2 Selection of External Device" (page 7)

3Example of Communication Settings

This section shows setting examples for

communicating between the display and

the External Device.

)"3 Example of Communication Setting"

(page 8)

4Setup Items

This section describes communication

setup items on the display.

Set communication settings of Display

with GP-Pro Ex or in off-line mode.

)"4 Setup Items" (page 15)

5)"5 Cable Diagram" (page 20)

Operation

Cable Diagram

This section shows cables and adapters

for connecting the display and the External

Device.

FX Series Computer Link Driver

GP-Pro EX Device/PLC Connection Manual 3

1 System Configuration

The system configuration in the case when the External Device of Mitsubishi Electric Corp. and the display are

connected is shown.

Series

CPU Link I/F*1 SIO Type Setting Example Cable Diagram

Series

FX0N *2

FX1NC

FX2NC

FX0N-232ADP RS232C Setting Example 1

(page 8) Cable Diagram 2

(page 21)

FX2NC-232ADP RS232C Setting Example 1

(page 8) Cable Diagram 1

(page 20)

FX0N-485ADP,

FX2NC-485ADP

RS422/485

(4wire) Setting Example 3

(page 13) Cable Diagram 3

(page 22)

RS422/485

(2wire) Setting Example 2

(page 11) Cable Diagram 4

(page 27)

FX1S

FX1N

FX1N-232-BD,

FX2NC-232ADP+FX1N-CNV-BD RS232C Setting Example 1

(page 8) Cable Diagram 1

(page 20)

FX0N-232ADP+FX1N-CNV-BD RS232C Setting Example 1

(page 8) Cable Diagram 2

(page 21)

FX1N-485-BD,

FX0N-485ADP+FX1N-CNV-BD,

FX2NC-485ADP+FX1N-CNV-BD

RS422/485

(4wire) Setting Example 3

(page 13) Cable Diagram 3

(page 22)

RS422/485

(2wire) Setting Example 2

(page 11) Cable Diagram 4

(page 27)

FX2N *3

FX2N-232-BD,

FX2NC-232ADP+FX2N-CNV-BD RS232C Setting Example 1

(page 8) Cable Diagram 1

(page 20)

FX0N-232ADP+FX2N-CNV-BD RS232C Setting Example 1

(page 8) Cable Diagram 2

(page 21)

FX2N-485-BD,

FX0N-485ADP+FX2N-CNV-BD,

FX2NC-485ADP+FX2N-CNV-BD

RS422/485

(4wire) Setting Example 3

(page 13) Cable Diagram 3

(page 22)

RS422/485

(2wire) Setting Example 2

(page 11) Cable Diagram 4

(page 27)

FX3UC-

32MT-

LT(-2) *4

FX3U *4

*When using channel 1 (Ch1)

FX3U-232-BD,

FX3U-232ADP+FX3U-CNV-BD

*When using channel 2 (Ch2)

FX3U-232ADP+FX3U--BD,

FX3U-232ADP*5 +FX3U-ADP

+FX3U-CNV-BD

RS232C Setting Example 1

(page 8) Cable Diagram 1

(page 20)

*When using channel 1 (Ch1)

FX3U-485-BD,

FX3U-485ADP+FX3U-CNV-BD

*When using channel 2 (Ch2)

FX3U-485ADP+FX3U--BD,

FX3U-485ADP*6 +FX3U-ADP

+FX3U-CNV-BD

RS422/485

(4wire) Setting Example 3

(page 13) Cable Diagram 3

(page 22)

RS422/485

(2wire) Setting Example 2

(page 11) Cable Diagram 4

(page 27)

FX Series Computer Link Driver

GP-Pro EX Device/PLC Connection Manual 4

Series

FX3UC

(D,DSS)

*When using channel 1 (Ch1)

FX3U-232ADP

*When using channel 2 (Ch2)

FX3U-232ADP*5+FX3U-ADP

RS232C Setting Example 1

(page 8) Cable Diagram 1

(page 20)

*When using channel 1 (Ch1)

FX3U-485ADP

*When using channel 2 (Ch2)

FX3U-485ADP*6+FX3U-ADP

RS422/485

(4wire) Setting Example 3

(page 13) Cable Diagram 3

(page 22)

RS422/485

(2wire) Setting Example 2

(page 11) Cable Diagram 4

(page 27)

FX3G

(14,24

points

type)

FX3G-232-BD,

FX3U-232ADP+ FX3G-CNV-ADP RS232C Setting Example 1

(page 8) Cable Diagram 1

(page 20)

FX3G-485-BD,

FX3U-485ADP+FX3G-CNV-ADP

RS422/485

(4wire) Setting Example 3

(page 13) Cable Diagram 3

(page 22)

RS422/485

(2wire) Setting Example 2

(page 11) Cable Diagram 4

(page 27)

FX3G

(40,60

points

type)*4

*When using channel 1 (Ch1)

FX3G-232-BD (When connecting to

Connector 1 for optional units),

FX3U-232ADP+FX3G-CNV-ADP

*When using channel 2 (Ch2)

FX3G-232-BD (When connecting to

Connector 2 for optional units),

FX3U-232ADP*5+FX3U-ADP

+FX3G-CNV-ADP

RS232C Setting Example 1

(page 8) Cable Diagram 1

(page 20)

*When using channel 1 (Ch1)

FX3G-485-BD (When connecting to

Connector 1 for optional units),

FX3U-485ADP+FX3G-CNV-ADP

*When using channel 2 (Ch2)

FX3G-485-BD (When connecting to

Connector 2 for optional units),

FX3U-485ADP*6+FX3U-ADP

+FX3G-CNV-ADP

RS422/485

(4wire) Setting Example 3

(page 13) Cable Diagram 3

(page 22)

RS422/485

(2wire) Setting Example 2

(page 11) Cable Diagram 4

(page 27)

*1 Any of 232, 422, 485 and USB is shown in .

Either of 232 or 485 is shown in .

*2 System version 1.20 or higher for External Device is required. You can monitor the special register D8001 to check

the system version for External Device. Please refer to the manual of External Device for more details.

*3 System version 1.06 or higher for External Device is required. You can monitor the special register D8001 to check

the system version for External Device. Please refer to the manual of External Device for more details.

*4 Simultaneous communication of Ch1 and Ch2 is available.

*5 FX3U-232ADP is assigned to Ch2.

*6 FX3U-485ADP is assigned to Ch2.

Series

CPU Link I/F*1 SIO Type Setting Example Cable Diagram

FX Series Computer Link Driver

GP-Pro EX Device/PLC Connection Manual 5

IPC COM Port

When connecting IPC with an External Device, the COM port used depends on the series and SIO type. Please

refer to the IPC manual for details.

Usable port

DIP switch setting: RS-232C

Series Usable Port

RS-232C RS-422/485(4 wire) RS-422/485(2 wire)

PS-2000B COM1*1 , COM2,

COM3*1, COM4

*1 The RI/5V can be switched. Use the IPC’s switch to change if necessary.

PS-3450A, PS-3451A,

PS3000-BA, PS3001-BD COM1, COM2*1*2 COM2*1*2 COM2*1*2

PS-3650A, PS-3651A COM1*1 --

PS-3700A (Pentium®4-M)

PS-3710A COM1*1, COM2*1,

COM3*2 , COM4

*2 Set up the SIO type with the DIP switch. Please set up as follows according to SIO type to be used.

COM3*2 COM3*2

PS-3711A COM1*1, COM2*2 COM2*2 COM2*2

PL-3000B, PL-3600T,

PL-3600K, PL-3700T,

PL-3700K, PL-3900T

COM1*1*2, COM2*1,

COM3, COM4 COM1*1*2 COM1*1*2

DIP switch Setting Description

1OFF

*1 When using PS-3450A, PS-3451A, PS3000-BA and PS3001-BD, turn ON the set value.

Reserved (always OFF)

2OFF

SIO type: RS-232C

3OFF

4 OFF Output mode of SD (TXD) data: Always output

5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None

6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None

7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Not available

8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Not available

9OFF

RS (RTS) Auto control mode: Disabled

10 OFF

FX Series Computer Link Driver

GP-Pro EX Device/PLC Connection Manual 6

DIP switch setting: RS-422/485 (4 wire)

DIP switch setting: RS-422/485 (2 wire)

DIP switch Setting Description

1 OFF Reserved (always OFF)

2ON

SIO type: RS-422/485

3ON

4 OFF Output mode of SD (TXD) data: Always output

5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None

6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None

7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Not available

8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Not available

9OFF

RS (RTS) Auto control mode: Disabled

10 OFF

DIP switch Setting Description

1 OFF Reserved (always OFF)

2ON

SIO type: RS-422/485

3ON

4 OFF Output mode of SD (TXD) data: Always output

5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None

6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None

7 ON Short-circuit of SDA (TXA) and RDA (RXA): Available

8 ON Short-circuit of SDB (TXB) and RDB (RXB): Available

9ON

RS (RTS) Auto control mode: Enabled

10 ON

FX Series Computer Link Driver

GP-Pro EX Device/PLC Connection Manual 7

2 Selection of External Device

Select the External Device to be connected to the Display.

Setup Items Setup Description

Maker Select the maker of External Device to be connected. Select "Mitsubishi Electric

Corporation".

Series

Select a model (series) of External Device to be connected and connection method.

Select "FX Series Computer Link".

Check External Device which can be connected in "FX Series Computer Link" in

system configuration.

)"1 System Configuration" (page 3)

Use System Area

Check this option when you synchronize the system data area of Display and the device

(memory) of External Device. When synchronized, you can use the ladder program of

External Device to switch the display or display the window on the display.

Cf. GP-Pro EX Reference Manual "Appendix 1.4 LS Area (Direct Access

Method)"

This can also be set in GP-Pro EX or in the Display's off-line mode.

Cf. GP-Pro EX Reference Manual "5.17.6 [System Settings] Setting Guide,

[Display Unit] Settings Guide, System Area Settings"

Cf. Maintenance/Troubleshooting Manual "2.15.1 Settings common to all

Display models, [Main Unit Settings] Settings Guide, System Area

Settings"

Port Select the Display port to be connected to the External Device.

FX Series Computer Link Driver

GP-Pro EX Device/PLC Connection Manual 8

3 Example of Communication Setting

Examples of communication settings of the display and the External Device, recommended by Pro-face, are

shown.

When you use the FX Series, use GP-Pro EX and the ladder software to set as below.

3.1 Setting Example 1

Setting of GP-Pro EX

Communication Settings

To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.

FX Series Computer Link Driver

GP-Pro EX Device/PLC Connection Manual 9

Device Setting

To display the setting screen, click ([Setting]) of External Device you want to set from [Device-Specific

Settings] of [Device/PLC Settings ].

When you connect multiple External Devices, click from [Device-Specific Settings] of [Device/PLC Settings]

to add another External Device.

FX Series Computer Link Driver

GP-Pro EX Device/PLC Connection Manual 10

Setting of External Device

Setting of External Device includes the setting with parameter and the setting by writing data to the special data

Setting with parameter

Double-click [PC parameter] from [Parameter] in the tree view of the ladder software to display the [FX

parameter] dialog box.

Click the [PC system settings (2)] tab for communication settings.

Setup items and description are shown below.

Setting by writing data to the special data register

Write data to the data register of External Device. After writing, turn the power of External Device from OFF to

ON.

Write destination data register and write data are shown below.

• FX0N does not support the setting with parameter. Select the setting by writing data to the

special data register.

Setup Items Setup Description

CH*1

*1 Setting only for FX3UC, FX3U and FX3G.

CH1 or CH2

Protocol Protocol communication only

Data Length 7

Parity Even

Stop Bit 2

Line Speed Match with the speed of Display

Header None

Terminator None

H/W Type Normal/RS232C

Sum Check Added

Control method Form 4

Timeout 1

• When using the FX0N Series, turn ON M8120 for keeping communication settings before

turning power from OFF to ON.

Write Destination Data Register Write data

CH1 of FX3UC, FX3U, FX3G and

FX Series except above CH2 of FX3UC, FX3U

and FX3G

D8120 D8420 0xE89E

D8121 D8421 0

D8129 D8429 1

Andere Handbücher für FX2NC-485ADP

Inhaltsverzeichnis

Andere Mitsubishi Controller Handbücher

Mitsubishi

Mitsubishi Q64AD Bedienungsanleitung

Mitsubishi

Mitsubishi CR760-Q Bedienungsanleitung

Mitsubishi

Mitsubishi A1SJ61BT11 Bedienungsanleitung

Mitsubishi

Mitsubishi QD51-R24 Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-A series Bedienungsanleitung

Mitsubishi

Mitsubishi A Series Bedienungsanleitung

Mitsubishi

Mitsubishi FX2N-32DP-IF Bedienungsanleitung

Mitsubishi

Mitsubishi Q2ACPU Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-FX0N Series Bedienungsanleitung

Mitsubishi

Mitsubishi FX2N-232IF Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-A series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-F Installationsanleitung

Mitsubishi

Mitsubishi FX-30P Bedienungsanleitung

Mitsubishi

Mitsubishi AL-6MR-A Bedienungsanleitung

Mitsubishi

Mitsubishi melservo-j2 series Bedienungsanleitung

Mitsubishi

Mitsubishi CR800 Series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-A AJ71E71-S3 Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-Q/L Betriebsanleitung

Mitsubishi

Mitsubishi G-50A Bedienungsanleitung

Mitsubishi

Mitsubishi FX3U-32DP Bedienungsanleitung

Mitsubishi

Mitsubishi Q64TCRT Bedienungsanleitung

Mitsubishi

Mitsubishi QS03NB-U-HW Bedienungsanleitung

Mitsubishi

Mitsubishi FX2NC-16EX Anleitungen und Rezepte

Mitsubishi

Mitsubishi MELSEC-L Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung