Mitsubishi FX2NC DSS Series Bedienungsanleitung

DSS/DS

HARDWARE MANUAL

FX2NC (DSS/DS) SERIES PROGRAMMABLE CONTROLLERS

Санкт-Петербург, ул. Седова, д.53

+7 (812) 7-028-029

[email protected] www.elinc.ru

FX2NC Series Programmable Controllers

Foreword

• This manual contains text, diagrams and explanations which will guide the reader in the correct installation and

operation of the FX2NC. It should be read and understood before attempting to install or use the unit.

• Further information can be found in the FX2NC Series Hardware Manual and FX Series Programming Manual II.

• If in doubt at any stage of the installation of FX2NC always consult a professional electrical engineer who is

qualified and trained to the local and national standards that applies to the installation site.

• If in doubt about the operation or use of FX2NC please consult the nearest Mitsubishi Electric distributor.

• This manual is subject to change without notice.

FX2NC (DSS/DS) Series Programmable

Controllers

Hardware Manual

This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent

licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial

property rights which may occur as a result of using the contents noted in this manual.

FX2NC Series Programmable Controllers

Manual number :JY992D76401

Manual revision :G

Date :November 2005

FX2NC Series Programmable Controllers

Guidelines for the safety of the user and protection of the FX2NC.

This manual provides information for the installation and use of the FX2NC. The manual has

been written to be used by trained and competent personnel. The definition of such a person

or persons is as follows:

a) Any engineer who is responsible for the planning, design and construction of automatic

equipment using the product associated with this manual, should be of a competent

nature, trained and qualified to the local and national standards required to fulfill that

role. These engineers should be fully aware of all aspects of safety with regards to

automated equipment.

b) Any commissioning or service engineer must be of a competent nature, trained and

qualified to the local and national standards required to fulfill that job. These engineers

should also be trained in the use and maintenance of the completed product. This

includes being completely familiar with all associated documentation for said product. All

maintenance should be carried out in accordance with established safety practices.

c) All operators of the completed equipment (see Note) should be trained to use this

product in a safe manner in compliance to established safety practices. The operators

should also be familiar with documentation which is associated with the actual operation

of the completed equipment.

Note : The term ‘completed equipment’ refers to a third party constructed device which

contains or uses the product associated with this manual.

FX2NC Series Programmable Controllers

iii

Notes on the Symbols Used in this Manual

At various times throughout this manual certain symbols will be used to highlight points which

are intended to ensure the users personal safety and protect the integrity of equipment.

Whenever any of the following symbols are encountered its associated note must be read and

understood. Each of the symbols used will now be listed with a brief description of its meaning.

Hardware warnings

Software warning

1) Indicates that the identified danger WILL cause physical and property damage.

2) Indicates that the identified danger could POSSIBLY cause physical and property damage

3) Indicates a point of further interest or further explanation.

4) Indicates special care must be taken when using this element of software.

5) Indicates a special point which the user of the associate software element should be awar

of.

6) Indicates a point of interest or further explanation.

FX2NC Series Programmable Controllers

• Under no circumstances will Mitsubishi Electric be liable responsible for any consequential

damage that may arise as a result of the installation or use of this equipment.

• All examples and diagrams shown in this manual are intended only as an aid to

understanding the text, not to guarantee operation. Mitsubishi Electric will accept no

responsibility for actual use of the product based on these illustrative examples.

• Please contact a Mitsubishi Electric distributor for more information concerning applications

in life critical situations or high reliability.

FX2NC Series Programmable Controllers

Note Concerning the CE Marking

This note does not guarantee that an entire mechanical module produced in accordance with

the contents of this note will comply with the following standards. Compliance to EMC directive

and LVD directive of the entire mechanical module should be checked by the user /

manufacturer.

For more details please contact the local Mitsubishi Electric sales site.

FX2NC Series Programmable Controllers

EMC

The following products have shown compliance through direct testing (of the identified

standards below) and design analysis (through the creation of a technical construction file) to

the European Directive for Electromagnetic Compatibility (89/336/EEC) when used as directed

by the appropriate documentation.Refer to a manual or related material of each product for

details concerning products not included below.

Type : Programmable Controller (Open Type Equipment)

Models : MELSEC FX2NC series manufactured

from March 1st, 1999 FX2NC-MT-DSS Where  indicates:16,32,64,96

FX2NC-ËËEX-DS FX2NC-ËËEYT-DSS

Where ËË indicates:16,32

FX2NC-EEPROM-16 FX2NC-RTC

FX2NC-EEPROM-4C FX2NC-EEPROM16C

from August 1st, 1999 FX2NC-16MR-T-DS

FX2NC-16EX-T-DS FX2NC-16EYR-T-DS

from July 1st, 2001 FX2NC-ROM-CE1

from October 1st, 2002 FX2NC-232ADP FX2NC-485ADP

FX2NC Series Programmable Controllers

vii

Models : MELSEC FX0N series manufactured

from November 1st, 1995 FX0N-8EX-ES, FX0N-8EYR-ES, FX0N-8EYT-ESS

from February 1st, 1996 FX0N-8ER-ES, FX0N-16EX-ES, FX0N-16EYR-ES,

FX0N-16EYT-ESS

from April 1st, 1996 FX0N-8ER-ES/UL, FX0N-16EX-ES/UL, FX0N-16EYR-ES/UL,

FX0N-16EYT-ESS/UL

from May 1st, 1996 FX0N-232ADP FX0N-485ADP

from July 1st, 1996 Harmonized Products

FX0N-8EX-ES/UL, FX0N-8EYR-ES/UL, FX0N-8EYT-ESS/UL

Standard Remark

EN50081-2:1993 Electromagnetic compatibility

EN61000-6-4:2001 - Generic emission standard

Industrial environment

Compliance with all relevant aspects of the

standard.

(Radiated Emissions and Mains Terminal Voltage

Emissions)

EN61000-6-2:2001 Electromagnetic compatibility

- Generic immunity standard

Industrial environment

Compliance with all relevant aspects of the

standard.

(RF immunity,Fast Transients,ESD,Conducted,

Surge, Power magnetic fields,Voltage dips and

Voltage interruptions)

FX2NC Series Programmable Controllers

viii

Models : MELSEC FX2N series manufactured

from July 1st, 1997 FX2N-16EX-ES/UL FX2N-16EYR-ES/UL FX2N-16EYT-ESS/UL

from August 1st, 2005 FX2N-8ER-ES/UL FX2N-8EX-ES/UL

FX2N-8EYR-ES/UL FX2N-8EYT-ESS/UL

to March 31st,2002 [compliance with EN50081-2 (EN61000-6-4) and EN50082-2]

from April 1st 2002:Above mentioned products [compliance with EN50081-2

(EN61000-6-4) and EN61131-2]

Standard Remark

EN50081-2:1993Electromagnetic compatibility

EN61000-6-4 -Generic emission standard

:2001 Industrial environment

Compliance with all relevant aspects of the standard.

(Radiated Emissions and Mains Terminal Voltage

Emissions)

EN50082-2:1995 Electromagnetic compatibility

- Generic immunity standard

Industrial environment

Compliance with all relevant aspects of the standard.

(RF immunity,Fast Transients,ESD,Conducted, and

Power magnetic fields)

EN61131-2:1994 Programmable controllers

/A11:1996 - Equipment requirements

/A12:2000 and tests

Compliance with all relevant aspects of the standard.

(RF Immunity, Fast Transients , ESD and Damped

oscillatory wave)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Controller Handbücher

Mitsubishi

Mitsubishi MELSEC Q Series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC iQ-F series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-F Installationsanleitung

Mitsubishi

Mitsubishi QD60P8-G Bedienungsanleitung

Mitsubishi

Mitsubishi QJ71MT91 Bedienungsanleitung

Mitsubishi

Mitsubishi QJ71LP21 Bedienungsanleitung

Mitsubishi

Mitsubishi FX2N-32DP-IF Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC Q Series Bedienungsanleitung

Mitsubishi

Mitsubishi Alpha XL Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-F Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC iQ-F FX5 series Betriebsanleitung

Mitsubishi

Mitsubishi FX2NC-485ADP Bedienungsanleitung

Mitsubishi

Mitsubishi FX3U-64CCL Bedienungsanleitung

Mitsubishi

Mitsubishi FX3G Series Bedienungsanleitung

Mitsubishi

Mitsubishi Melsec FX-2DA Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC FX3U-4DA Bedienungsanleitung

Mitsubishi

Mitsubishi QJ71E71-100 Series Bedienungsanleitung

Mitsubishi

Mitsubishi FX3U Series Bedienungsanleitung

Mitsubishi

Mitsubishi FX0-14 Bedienungsanleitung

Mitsubishi

Mitsubishi AG-150A Bedienungsanleitung

Mitsubishi

Mitsubishi A Series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC iQ-F FX5-4AD-TC-ADP Bedienungsanleitung

Mitsubishi

Mitsubishi Q68TD-G-H01 Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-F FX3U-4AD-TC-ADP Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung