Mitsubishi LVP-X120A Bedienungsanleitung

APPENDIX

X120

LCD

Projector

User Manual

MODEL LVP-X120A

Control this projector by using a personal computer

This projector can be controlled by connecting a personal computer with RS-232C terminal.

Connection

Projector + IBM PC or IBM PC compatibles

RS-232C cable

to RS-232C

terminal

to Com1

Comport

D-SUB 9P Mini DIN 8P

Note: If your PC (IBM or IBM compatible) is equipped only with a 25-pin serial port connector,

a 25-pin serial port adapter is required. Contact your dealer for details.

RS-232C cable

to RS-232C

terminal

RS-232C adaptor

for Macintosh

to modem port

or printer port

D-SUB 9PD-SUB 9PMini DIN 8P Mini DIN 8P

Projector + Macintosh

APPENDIX

Functions can be controlled by a personal computer:

• Turn the ON or OFF

• Changing input signals

• Button input by remote control

• Reading warning data

• Picture adjustment

By making a programme, you can also control this projector by a personal computer automatically.

[EXAMPLE]

Time Movement Commands to be used (ASCII code)

8:40 a.m. Turn the power ON 0 0 !

Change input to RGB 0 0 _ r 1

0:20 p.m. Turn the power OFF 0 0 "

1:00 p.m. Turn the power ON 0 0 !

3:00 p.m. Change input to VIDEO 0 0 _ v 1

5:20 p.m. Turn the power OFF 0 0 "

1) Interface

Address code Function code Data code End code

HEX 30h 30h Function Data 0Dh

ASCII '0' '0' Function Data

[Address code] 30h 30h (In ASCII code, '0' '0') fixed.

[Function code] A code of each fixed control move

[Data code] A code of each fixed control data (number) and not always indicated.

[End code] 0Dh (In ASCII code, ' ') fixed.

3) Control sequence

(1) The command from a personal computer to the projector will be sent in 400ms.

(2) The projector will send a return command 400ms* after it has received an encode. if the command isn’t

received correctly, the projector will not send the retirn command.

(3) The personal computer checks the command and confirms that if the command which has been sent has

been executed or not.

(4) This projector sends various codes, other than the return code. When having a control sequence by RS-

232C, reject other codes from personal computer side.

• * : The sending time of return command may delay depending on the condition (during changing the input

signal, playing back the PC card, etc.).

PROTOCOL RS-232C

BAUD RATE 9600 [bps]

DATA LENGTH 8 [bits]

PARITY BIT NONE

STOP BIT 1 [bits]

FLOW CONTROL NONE

This projector uses RXD, TXD and GND lines for RS-232C control.

For RS-232C cable,the reverse type cable should be used.

2) Control command diagram

The command is structured by the address code, function code, data code and end code. The length of the

command is different by each function.

Control this projector by using a personal computer (Continue)

[Example] Turn the power ON (' 'is for ASCII code)

Sending commands Status code from Meaning

from the PC etc. projector

30 30 21 0D Command for POWER ON

'0' '0' '!' ' '

30 30 21 0D Command received

'0' '0' '!' ' ' (Command echo back)

4) Operation commands

The operation commands execute the basic operation setting of this projector.It may not operate when changing

the signal.

Sending commands Status code from Meaning

from the PC etc. projector

30 30 5F 72 31 OD Command for setting the input

'0' '0' '_' 'r' '1' ' ' signal to RGB

30 30 5F 72 31 OD Command received

'0' '0' '_' 'r' '1' ' ' (Command echo back)

Button's name on remote

ASCII HEX

+ VOLUME r06 72h 30h 36h

–VOLUME r07 72h 30h 37h

EXPAND r02 72h 30h 32h

{r53 72h 35h 33h

}r2b 72h 32h 62h

$r4f 72h 34h 66h

%r59 72h 35h 39h

MENU r54 72h 35h 34h

ENTER r10 72h 31h 30h

AUTO PLAY(PC CARD)

r32 72h 33h 32h

RELEASE(PC CARD)

r22 72h 32h 32h

AUTO POSITION r09 72h 30h 39h

STILL ra4 72h 61h 34h

Sending commands Status code from Meaning

from the PC etc. projector

30 30 72 35 34 OD Command as same as MENU button

'0' '0' 'r' '5' '4' ' '

30 30 72 35 34 OD Command received

'0' '0' 'r' '5' '4' ' ' (Command echo back)

ASCII HEX

POWER ON ! 21h

POWER OFF " 22h

INPUT RGB _r1 5Fh 72h 31h

INPUT VIDEO _v1 5Fh 76h 31h

INPUT CARD _c1 5Fh 63h 31h

•POWER OFF command will not work for 1 minute after the power is turned on.

•POWER ON command will not work for 1 minute after the power is turned off.

[Example] Set the input signal to RGB (' 'is for ASCII code)

[Example] Display MENU selection bar. (' 'is for ASCII code)

5) Remote commands

The some remote control operation can be done by remote command codes.

APPENDIX

6) Warning commands

Read the past warning data. The personal computer doesn’t attache the data code onto the warning commands to

send. On the other hand, the projector which has received a command, attach the warning data as the data code

to reply.

[Example 1]

The fan was down when the power was ON and the past data of the warning was confirmed.

Sending commands Status code from Meaning

from the PC etc. projector

30 30 45 70 OD Commnd for confirm past data

'0' '0' 'E' 'p' ' '

30 30 45 70 38 32 30 30 30 30 0D

Warning command (Fan is stopped when

'0' '0' 'E' 'p' '8' '2' '0' '0' '0' '0' ' ' the power is ON) carried out

The past data

Ep* (* is 6 digits, hexadecimal notation)

*=(MBS)b1,b2,b3,b4,b5,b6,b7,b8, b9, b10, b11, b12, b13, b14, b15, b16, b17, b18, b19, b20, b21, 000(LSB)

b1=Operation time (during boot up '0' / when the power is ON, '1')

b2=Standby power short

b3=Switch power short

b4=0

b5=0

b6=0

b7=The fan is stopped.

b8=The lamp cover is not closed.

b9=The filter cover is not closed.

b10=The temperature sensor is off (Exausting fan)

b11=The temperature sensor is off (The lamp)

b12=Communication error between microcomputer

b13=Communication error between microcomputer (Parallel bus)

b14=Abnormal temperature (the lamp)

b15=Abnormal temperature (outside)

b16=Abnormal temperature (LCD)

b17=The lamp is not illuminating.

b18=Confirmation mode for the operating status

b19=0

b20=0

b21= The life of a lamp

ASCII HEX

past data Ep 45h 70h

clear past data Ec 45h 63h

7) Reading command diagram

Monitor projector operation status. The power ON, OFF and input terminal settings can be monitored.

ASCII HEX

Function Data (Receive) Function Data (Receive)

POWER ON vP 1 76h 50h 31h

POWER OFF vP 0 76h 50h 30h

INPUT RGB vI r1 76h 49h 72h 31h

INPUT VIDEO vI v1 76h 49h 76h 31h

INPUT CARD vI c1 76h 49h 63h31h

* : '8' '2' '0' '0' '0' '0' mean the numbers as shown below.

Bit

b1 b2 b3 b4 b5 b6 b7 b8 b9 b10 b11 b12 b13 b14 b15 b16 b17 b18 b19 b20 b21 0 0 0

ASCII

10000010000000000000 0000

HEX

82 0000

b1=1(The power is ON), b7=1(The fan is stopped), Other=0

8) Picture adjustment commands

The picture adjustment commands execute the picture adjustment setting of this projector. If the personal computer doesn’t

send the commands without attaching the data code, the projector which has received the command replays the setting data

as data code.

How to set the grade

The data code of CONTRAST and BRIGHTNESS is structured by the difference data of R from G, the main data and the difference

data of B from G. Use ASCII letters code to set the grade for setting data. Please refer to the table below for HEX code.

ASCII HEX

CONTRAST P 50h

BRIGHTNESS Q 51h

SHARPNESS R 52h

TINT S 53h

COLOR T 54h

ASCII '+' '–' '0' '1' '2' '3' '4' '5' '6' '7' '8' '9'

HEX 2Bh 2Dh 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h

[Example 2] The TINT was set to +10 when the setting status was confirmed.

[Example 1] Set the difference data of R from G to +10, the setting main data to 0 and the difference data of

B from to -5.

Sending commands Status code from Meaning

from the PC etc. projector

30 30 50 2B 31 30 2B 30 30 2D 30 35 0D Command for setting the

'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' ' ' picture control

30 30 50 2B 31 30 2B 30 30 2D 30 35 0D Command received

'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' ' ' (Command echo back)

Sending commands Status code from Meaning

from the PC etc. projector

30 30 53 0D Command for confirm

'0' '0' 'S' ' 'setting of TINT

30 30 53 2B 31 30 0D Command (setting of TINT

'0' '0' 'S' '+' '1' '0' ' ' is +10) carried out

Control this projector by using a personal computer (Continue)

When a personal computer sends the command, data code will not be attached. On the other hand, the projector

which has received a command will attach the recent operating status then send.

[Example ] Input was Video when the operating status of the input terminal was confirmed.

Sending commands Status code from Meaning

from the PC etc. projector

30 30 76 49 OD Commnd for confirm input

'0' '0' 'v' 'I' ' '

30 30 76 49 76 31 0D Command (Input is Video)

'0' '0' 'v' 'I' 'v' '1' ' ' carrired out

CONTRAST

BRIGHTNESS

difference data

of R from G

-10

+00

difference data

of B from G

+10

+00

CONTRAST

BRIGHTNESS

difference data

of R from G

+10

+00

difference data

of B from G

-10

+00

• When the command of CONTRAST or BRIGHTNESS is sent from the computer, the setting of the COLOR TEMP on the

menu is set to “USER”.

• For the same condition as “HIGH” or “LOW” of the COLOR TEMP, change the CONTRAST and BRIGHTNESS settings as

shown below.

COLOR TEMP “HIGH” COLOR TEMP “LOW”

Printed in Japan871D269B1

MITSUBISHI ELECTRONICS AMERICA, INC.

5665 Plaza Drive

Cypress, CA 90630

Andere Handbücher für LVP-X120A

Inhaltsverzeichnis

Andere Mitsubishi Projektor Handbücher

Mitsubishi

Mitsubishi HD8000 Bedienungsanleitung

Mitsubishi

Mitsubishi LVP-X300U Bedienungsanleitung

Mitsubishi

Mitsubishi XD80U Bedienungsanleitung

Mitsubishi

Mitsubishi ColorView XL4U Bedienungsanleitung

Mitsubishi

Mitsubishi ColorView SL1U Bedienungsanleitung

Mitsubishi

Mitsubishi VS-1281 Bedienungsanleitung

Mitsubishi

Mitsubishi LVP-SA51U Bedienungsanleitung

Mitsubishi

Mitsubishi ES100U Bedienungsanleitung

Mitsubishi

Mitsubishi XD250U-ST Bedienungsanleitung

Mitsubishi

Mitsubishi HC1500 Bedienungsanleitung

Mitsubishi

Mitsubishi HC3800 Bedienungsanleitung

Mitsubishi

Mitsubishi DLP XD8600U Bedienungsanleitung

Mitsubishi

Mitsubishi DLP EW331U-ST Bedienungsanleitung

Mitsubishi

Mitsubishi WD380U-EST Bedienungsanleitung

Mitsubishi

Mitsubishi HC3000/HC910 Bedienungsanleitung

Mitsubishi

Mitsubishi SL4SU Bedienungsanleitung

Mitsubishi

Mitsubishi S290U Bedienungsanleitung

Mitsubishi

Mitsubishi WD380U-EST Bedienungsanleitung

Mitsubishi

Mitsubishi X120 Bedienungsanleitung

Mitsubishi

Mitsubishi LVP-X120A Bedienungsanleitung

Mitsubishi

Mitsubishi ColorView S490U Handbuch

Mitsubishi

Mitsubishi VS-SH10U Bedienungs- und Sicherheitshinweise

Mitsubishi

Mitsubishi S290U Bedienungsanleitung

Mitsubishi

Mitsubishi VS-50PH50U Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung