Mitsubishi GT16 Bedienungsanleitung

GT16 User's Manual (Hardware)

A - 1

SAFETY PRECAUTIONS

(Always read these precautions before using this equipment.)

Before using this product, please read this manual and the relevant manuals introduced in this manual

carefully and pay full attention to safety to handle the product correctly.

The precautions given in this manual are concerned with this product.

In this manual, the safety precautions are ranked as "WARNING" and "CAUTION".

Note that the caution level may lead to a serious accident according to the circumstances. Always

follow the instructions of both levels because they are important to personal safety.

Please save this manual to make it accessible when required and always forward it to the end user.

[DESIGN PRECAUTIONS]

WARNING

Some failures of the GOT, communication unit or cable may keep the outputs on or off.

Some failures of a touch panel may cause malfunction of the input objects such as a touch switch.

An external monitoring circuit should be provided to check for output signals which may lead to a

serious accident.

Not doing so can cause an accident due to false output or malfunction.

If a communication fault (including cable disconnection) occurs during monitoring on the GOT,

communication between the GOT and PLC CPU is suspended and the GOT becomes inoperative.

For bus connection: The CPU becomes faulty and the GOT becomes inoperative.

For other than bus connection: The GOT becomes inoperative.

A system where the GOT is used should be configured to perform any significant operation to the

system by using the switches of a device other than the GOT on the assumption that a GOT

communication fault will occur.

Not doing so can cause an accident due to false output or malfunction.

Do not use the GOT as the warning device that may cause a serious accident.

An independent and redundant hardware or mechanical interlock is required to configure the device

that displays and outputs serious warning.

Failure to observe this instruction may result in an accident due to incorrect output or malfunction.

WARNING Indicates that incorrect handling may cause hazardous

conditions, resulting in death or severe injury.

CAUTION

Indicates that incorrect handling may cause hazardous

conditions, resulting in medium or slight personal injury or

physical damage.

A - 2

[DESIGN PRECAUTIONS]

WARNING

Incorrect operation of the touch switch(s) may lead to a serious accident if the GOT backlight is gone

out.

When the GOT backlight goes out, although the POWER LED blinks (green/orange) and the display

section dims, the input of the touch switch(s) remains active.

This may confuse an operator in thinking that the GOT is in "screensaver" mode, who then tries to

release the GOT from this mode by touching the display section, which may cause a touch switch to

operate.

Note that the following occurs on the GOT when the backlight goes out.

• GT1655-V: The POWER LED blinks (green/orange) and the monitor screen appears blank.

• Models other than GT1655-V: The POWER LED blinks (green/orange) and the monitor screen

appears dimmed.

The display section of the GT16 is an analog-resistive type touch panel.

If you touch the display section simultaneously in 2 points or more, the switch that is located around

the center of the touched point, if any, may operate.

Do not touch the display section in 2 points or more simultaneously.

Doing so may cause an accident due to incorrect output or malfunction.

When programs or parameters of the controller (such as a PLC) that is monitored by the GOT are

changed,be sure to reset the GOT or shut off the power of the GOT at the same time.

Not doing so can cause an accident due to false output or malfunction.

CAUTION

Do not bundle the control and communication cables with main-circuit, power or other wiring.

Run the above cables separately from such wiring and keep them a minimum of 100mm (3.94in.)

apart.Not doing so noise can cause a malfunction.

Do not press the GOT display section with a pointed material as a pen or driver.

Doing so can result in a damage or failure of the display section.

When the GOT is connected to the Ethernet network, the available IP address is restricted according

to the system configuration.

• When multiple GOTs are connected to the Ethernet network:

Do not set the IP address (192.168.0.18) for the GOTs and the controllers in the network.

• When a single GOT is connected to the Ethernet network:

Do not set the IP address (192.168.0.18) for the controllers except the GOT in the network.

Doing so can cause the IP address duplication. The duplication can negatively affect the

communication of the device with the IP address (192.168.0.18).

The operation at the IP address duplication depends on the devices and the system.

Turn on the controllers and the network devices to be ready for communication before they

communicate with the GOT.

Failure to do so can cause a communication error on the GOT.

A - 3

[MOUNTING PRECAUTIONS]

WARNING

Be sure to shut off all phases of the external power supply used by the system before mounting or

removing the GOT main unit to/from the panel.

Not doing so can cause the unit to fail or malfunction.

Be sure to shut off all phases of the external power supply used by the system before mounting or

removing the communication unit, printer unit or option function board onto/from the GOT.

Not doing so can cause the unit to fail or malfunction.

When installing the option function board, wear an earth band etc. to avoid the static electricity.

Not doing so can cause a unit corruption.

CAUTION

Use the GOT in the environment that satisfies the general specifications described in this manual.

Not doing so can cause an electric shock, fire, malfunction or product damage or deterioration.

When mounting the GOT to the control panel, tighten the mounting screws in the specified torque

range (0.36 to 0.48 N•m) with a Phillips-head screwdriver No.2.

Undertightening can cause the GOT to drop, short circuit or malfunction.

Overtightening can cause a drop, short circuit or malfunction due to the damage of the screws or the

GOT.

When loading the communication unit to the GOT, fit it to the connection interface of the GOT and

tighten the mounting screws in the specified torque range (0.36 to 0.48 N•m) with a Phillips-head

screwdriver No.2.

Undertightening can cause the GOT to drop, short circuit or malfunction.

Overtightening can cause a drop, failure or malfunction due to the damage of the screws or unit.

When mounting the option function board onto the GOT, connect it to the corresponding connector

securely and tighten the mounting screws within the specified torque range (0.25 to 0.35 N•m) with a

Phillips-head screwdriver No.1.

Undertightening can cause malfunction due to poor contact.

Overtightening can cause malfunction due to screw or unit damage.

When inserting a CF card into the GOT, push it into the CF card interface of GOT until the CF card

eject button will pop out.

If not properly inserted, a bad connection may cause a malfunction.

When inserting/removing a CF card into/from the GOT, turn the CF card access switch off in

advance.

Failure to do so may corrupt data within the CF card.

When removing a CF card from the GOT, make sure to support the CF card by hand, as it may pop

out.

Failure to do so may cause the CF card to drop from the GOT and break.

A - 4

[MOUNTING PRECAUTIONS]

[WIRING PRECAUTIONS]

CAUTION

When installing a USB memory to the GOT, make sure to install the USB memory to the USB

interface firmly.

Failure to do so may cause a malfunction due to poor contact.

Before removing the USB memory from the GOT, operate the utility screen for removal. After the

successful completion dialog box is displayed, remove the memory by hand carefully.

Failure to do so may cause the USB memory to drop, resulting in a damage or failure of the memory.

For closing the USB environmental protection cover, fix the cover by pushing the mark on the

latch firmly to comply with the protective structure.

Remove the protective film of the GOT.

When the user continues using the GOT with the protective film, the film may not be removed.

Operate and store the GOT in environments without direct sunlight, high temperature, dust, humidity,

and vibrations.

When using the GOT in the environment of oil or chemicals, use the protective cover for oil.

Failure to do so may cause failure or malfunction due to the oil or chemical entering into the GOT.

WARNING

Be sure to shut off all phases of the external power supply used by the system before wiring.

Failure to do so may result in an electric shock, product damage or malfunctions.

CAUTION

Make sure to ground the FG terminal, LG terminal, and functional ground terminal of the GOT power

supply section with a ground resistance of 100Ωor less solely for the GOT.

Not doing so may cause an electric shock or malfunction.

When tightening the terminal screws, use a Phillips-head screwdriver No.2.

Terminal screws which are not to be used must be tightened always at torque 0.5 to 0.8 N·m.

Otherwise there will be a danger of short circuit against the solderless terminals.

Use applicable solderless terminals and tighten them with the specified torque.

If any solderless spade terminal is used, it may be disconnected when the terminal screw comes

loose, resulting in failure.

Correctly wire the GOT power supply section after confirming the rated voltage and terminal

arrangement of the product.

Not doing so can cause a fire or failure.

A - 5

[WIRING PRECAUTIONS]

[TEST OPERATION PRECAUTIONS]

[STARTUP/MAINTENANCE PRECAUTIONS]

CAUTION

Tighten the terminal screws of the GOT power supply section in the specified torque range (0.5 to

0.8 N.m).

Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the screws or the GOT.

Exercise care to avoid foreign matter such as chips and wire offcuts entering the GOT. Not doing so

can cause a fire, failure or malfunction.

The module has an ingress prevention label on its top to prevent foreign matter, such as wire offcuts,

from entering the module during wiring.

Do not peel this label during wiring.

Before starting system operation, be sure to peel this label because of heat dissipation.

Plug the communication cable into the connector of the connected unit and tighten the mounting and

terminal screws in the specified torque range.

Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.

Plug the QnA/ACPU/Motion controller (A series) bus connection cable by inserting it into the

connector of the connected unit until it "clicks".

After plugging, check that it has been inserted snugly.

Not doing so can cause a malfunction due to a contact fault.

WARNING

Before performing the test operations of the user creation monitor screen (such as turning ON or

OFF bit device, changing the word device current value, changing the settings or current values of

the timer or counter, and changing the buffer memory current value), read through the manual

carefully and make yourself familiar with the operation method.

During test operation, never change the data of the devices which are used to perform significant

operation for the system.

False output or malfunction can cause an accident.

WARNING

When power is on, do not touch the terminals.

Doing so can cause an electric shock or malfunction.

A - 6

[STARTUP/MAINTENANCE PRECAUTIONS]

WARNING

Correctly connect the battery connector.

Do not perform the following actions to the battery.

• Charging, disassembling, heating, short-circuiting, or soldering the battery, or throwing it into the

fire

Doing so will cause the battery to produce heat, explode, or ignite, resulting in injuly and fire.

Before starting cleaning or terminal screw retightening, always switch off the power externally in all

phases.

Not switching the power off in all phases can cause a unit failure or malfunction.

Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.

CAUTION

Do not disassemble or modify this unit.

Doing so can cause a failure, malfunction, injury, or fire.

Do not touch the conductive and electronic parts of the unit directly.

Doing so can cause a unit malfunction or failure.

The cables connected to the unit must be run in ducts or clamped.

Not doing so can cause the unit or cable to be damaged due to the dangling, motion or accidental

pulling of the cables or can cause a malfunction due to a cable connection fault.

When unplugging the cable connected to the unit, do not hold and pull the cable portion.

Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable

connection fault.

Do not drop the module or subject it to strong shock.

A module damage may result.

Do not drop or give an impact to the battery mounted to the unit.

Doing so may damage the battery, causing the battery fluid to leak inside the battery.

If the battery is dropped or given an impact, dispose of it without using.

Before touching the unit, always touch grounded metal, etc. to discharge static electricity from

human body, etc.

Not doing so can cause the unit to fail or malfunction.

Replace battery with GT15-BAT or GT11-50BAT by Mitsubishi electric Co. only.

Use of another battery may present a risk of fire or explosion.

Dispose of used battery promptly.

Keep away from children. Do not disassemble and do not dispose of in fire.

A - 7

[TOUCH PANEL PRECAUTIONS]

[COLD CATHODE TUBE BACKLIGHT REPLACEMENT

PRECAUTIONS]

[DISPOSAL PRECAUTIONS]

CAUTION

For the analog-resistive film type touch panels, normally the adjustment is not required.

However, the difference between a touched position and the object position may occur as the period

of use elapses. When any difference between a touched position and the object position occurs,

execute the touch panel calibration.

When any difference between a touched position and the object position occurs, other objectsmay

be activated. This may cause an unexpected operation due to incorrect output or malfunction.

WARNING

Be sure to shut off all phases of the external power supply of the GOT (and the PLC CPU in the case

of a bus topology) and remove the GOT from the control panel before replacing the backlight (when

using the GOT with the backlight replaceable by the user).

Not doing so can cause an electric shock.

Replacing a backlight without removing the GOT from the control panel can cause the backlight to

drop, resulting in an injury.

CAUTION

Wear gloves for the backlight replacement when using the GOT with the backlight replaceable by the

user.

Not doing so can cause an injury.

Before replacing a backlight, allow 5 minutes or more after turning off the GOT when using the GOT

with the backlight replaceable by the user.

Not doing so can cause a burn from heat of the backlight.

CAUTION

When disposing of this product, treat it as industrial waste.

When disposing of batteries, separate them from other wastes according to the local regulations.

(For details of the battery directive in EU member states, refer to Handling of Batteries and Devices

with Built-in Batteries in EU Member States.)

A - 8

[TRANSPORTATION PRECAUTIONS]

CAUTION

When transporting lithium batteries, make sure to treat them based on the transport regulations.

(Refer to Appendix 3 for details of the regurated models.)

Make sure to transport the GOT main unit and/or relevant unit(s) in the manner they will not be

exposed to the impact exceeding the impact resistance described in the general specifications of this

manual, as they are precision devices.

Failure to do so may cause the unit to fail.

Check if the unit operates correctly after transportation.

Andere Handbücher für GT16

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Touch-Terminal Handbücher

Mitsubishi

Mitsubishi GT10 Bedienungsanleitung

Mitsubishi

Mitsubishi GT11 Bedienungsanleitung

Mitsubishi

Mitsubishi F930GOT-BBD-K-E Bedienungsanleitung

Mitsubishi

Mitsubishi GT1150-QLBD Bedienungsanleitung

Mitsubishi

Mitsubishi GOT-A900 Series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC GOT-F900 Bedienungsanleitung

Mitsubishi

Mitsubishi GOT1000 GT11 Bedienungsanleitung

Mitsubishi

Mitsubishi GOT2000 Series Gebrauchsanweisung

Mitsubishi

Mitsubishi A953GOT-SBD-M3-H Bedienungsanleitung

Mitsubishi

Mitsubishi GT14 Bedienungsanleitung

Mitsubishi

Mitsubishi GT10 Bedienungsanleitung

Mitsubishi

Mitsubishi A950GOT Bedienungsanleitung

Mitsubishi

Mitsubishi 900 Series Bedienungsanleitung

Mitsubishi

Mitsubishi GOT1000 Series Gebrauchsanweisung

Mitsubishi

Mitsubishi 900 Series Bedienungsanleitung

Mitsubishi

Mitsubishi GT1275-VNBA Bedienungs- und Montageanleitung

Mitsubishi

Mitsubishi F940GOT-SWD-E Bedienungsanleitung

Mitsubishi

Mitsubishi GOT1000 Series Gebrauchsanweisung

Mitsubishi

Mitsubishi GT16 Bedienungsanleitung

Mitsubishi

Mitsubishi GOT MELSEC 800 Series Bedienungsanleitung

Mitsubishi

Mitsubishi GOT1000 GT15 Bedienungsanleitung

Mitsubishi

Mitsubishi F940WGOT-TWD Bedienungsanleitung

Mitsubishi

Mitsubishi F930GOT-BBD-K-E Bedienungsanleitung

Mitsubishi

Mitsubishi F940 Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung

Prestel

Prestel VCS-G2PRO Bedienungsanleitung