Mitsubishi PAC-KE07DM-E Bedienungsanleitung

PRECAUTIONS BEFORE TEST RUN

PRECAUTIONS BEFORE REMOVE AND ELECTRIC WORK

WARNING

Always have the unit installed by Authorized Mitsubishi

Representative or similar professional.

Improper installation by the user could result in problems such as

water leakage, electric shock or fire.

Install the unit according to this Installation Manual.

If the unit is installed improperly, water leakage, electric shock or fire

may result.

Always use the designated cables and connect them properly.

When connecting the terminals, make sure that external forces

from the cable is not being conveyed to the terminal and then

tighten it securely.

Improper or loose connections could cause excessive heat or fire.

Only use Mitsubishi-approved accessories, such as an air

cleaner, humidifier or electric heater.

Always have such accessories installed by an Authorized Mitsubishi

Representative or similar professional. Improper installation by the

user may result in water leakage, electric shock or fire.

Have all electric work performed by a properly licensed electri-

cian. Electric work should be performed in strict adherence to

procedures to this Installation Manual. Always provide a dedi-

cated power supply.

If the capacity of the power supply is inadequate, it could result in

problems such electric shock or fire.

Never modify the unit and always have repairs performed by an

Authorized Mitsubishi Representative.

Improper repair could result in problems such water leakage, electric

shock or fire.

This installation manual contains only the description of how to install the Drain pump PAC-KE07DM-E. For information about how to wire and

how to install air conditioning units, see the installation manual for them.

For your safety, first be sure to read “ 1 Safety Precautions “ described below thoroughly and then install the Drain pump PAC-KE07DM-E

correctly.

This symbol denotes what could lead to serious injury or death if your misuse the PAC-KE07DM-E.

This symbol denotes what could lead to a personal injury or damage to your property if you misuse the PAC-KE07DM-E.

●The following two symbols are used to denote dangers that may be caused by incorrect use and their degree:

●After reading this installation manual, keep it in a place where the final user can see it anytime he or she wants to it.

When someone moves, repairs or uses the PAC-KE07DM-E, make sure that this manual is forwarded to the final user.

.WARNING

.CAUTION

Never use for special applications such as storing food, plants,

precision equipment or art.

The quality of these items may deteriorate.

Always provide adequate signal noise protection when

installing in facilities such as hospitals and communication sta-

tions.

Equipment at these facilities, such as inverters, in-house generators,

high-frequency medical equipment, two-way communication equip-

ment, may cause the air conditioner to operate improperly.

Conversely, the signal noise from the air conditioner may affect the

operation of medical equipment and two-way communication equip-

ment and this could interfere with the medical treatment being given

a patient or cause disturbances or interference in video broadcasting

equipment.

Never operate the air conditioner with the air filter removed.

Particles will enter into the air conditioner and cause damage.

Route wiring so that there is no tension.

Tension could cause the wire to break and this could result in exces-

sive heat or fire.

Dispose of packing materials properly.

Never use the unit in special environments.

Special environments with high concentrations of oil, steam or sulfu-

ric gases will reduce the performance of the air condition and cause

its parts to deteriorate.

Never turn off the power supply immediately after stopping the

unit.

Wait five minutes or more before turning off the power supply.

Turning off the power supply before that time could result in water

leakage or damage.

Never install the unit where run-off could result in damage.

If the humidity in the room exceeds 80% or if the drain becomes

clogged, water may drain off of the indoor unit. When the unit is used

for heating, there may be drainage from the outdoor unit. If required,

provide collector drain for the outdoor unit.

Use care when transporting the unit.

•Always use two or more people for lifting a product weight 20 kg. or

more.

•Some products are packaged with plastic wrapping bands. Never

use these for lifting or transporting the product.

•Never touch the fins on the heat exchanger. They are sharp and

could cause cuts.

•Never allow children to play with the plastic bags used for packag-

ing. Always tear them up when disposing. A child could suffocate

in these bags.

Never touch the switch with wet hands.

Electric shock could occur.

Never operate the air conditioner with the panel or guard

removed.

The hand could come in contact with rotating, hot or high-pressure

components. They could cause electrical shock or entanglement.

MITSUBISHI ELECTRIC

Air Conditioning For Building Application

Drain pump PAC-KE07DM-E

Installation Manual

WT05243X01

1 Safety Precautions

CAUTION

PRECAUTIONS BEFORE INSTALLATION

2 Confirming the Supplied Parts

1. Model names and applicable models

Applicable typesModel name

PAC-KE07DM-E

SEZ-M25DA(L), SEZ-M35DA(L), SEZ-M50DA(L)

SEZ-M60DA(L), SEZ-M71DA(L)

PEFY-P15VMS1L-E, PEFY-P20VMS1L-E

PEFY-P25VMS1L-E, PEFY-P32VMS1L-E

PEFY-P40VMS1L-E, PEFY-P50VMS1L-E

PEFY-P63VMS1L-E

Item 12 3 4 5

Quantity 1 1 1

(385mm) (255mm) (200mm)

(100mm)

(380mm)(175mm)

Shape

Item 6789 0

Quantity 1 3 3 1 2

Shape

Item

Quantity 1 1 6

Shape

131211

DRAIN PUMP ATTACHMENT DRAIN HOSE 1 PIPE COVER 1 PIPE COVER 2

HOSE BAND SCREW CLAMP FERRITE CLAMP BAND 1

PIPE COVER 3DRAIN HOSE 2 BAND 2

2. Provided parts

Check that the packet includes the following parts in addition to this installation manual.

3 Installing the Drain Pump

Hook the 2ATTCHMENT over the mounting bracket on the unit.

(b)

(a)

2ATTACHMENT

Cover

7SCREW

2ATTACHMENT

7SCREW

4~7mm

Cover

1DRAIN PUMP

Cover fixing screws

3-1 Installing the Drain Pump

(1) Unscrew the (a)screw on the unit cover, hook the

2ATTACHMENT over the mounting bracket on the unit,

and screw it on to the unit with the (a)screw. (Fig. 1)

(2) Temporarily screw in the 7SCREW in the hole (b) on

the 2ATTACHMENT. (Fig. 1 and 2)

(3) Loosen the drain-pump-cover fixing screws, and remove

the cover. (Fig. 3)

(4) Hang the 1DRAIN PUMP on the 2ATTACHMENT by

placing the 7SCREW (the one screwed in during Step

(2) above) through the Figure-8 hole on back of the

1DRAIN PUMP, and then tighten the 7SCREW from

inside the 1DRAIN PUMP. (Fig. 4)

Fig. 1

Fig. 2

Fig. 4

Fig. 3

3-2 Installing DRAIN HOSE 1

(1) Connect each end of 3DRAIN HOSE 1 to the drain port

on the unit and on the drain pump. (Fig. 5)

✻ Insert the hose all the way to the end of the ports.

✻ Do not use any adhesive.

(2) Secure the hose with 6HOSE BANDs at both ends of

the hose. (Fig. 5)

(3) Attach 4PIPE COVER 1 and 5PIPE COVER 2 to

3DRAIN HOSE 1 flush against each other and against

the unit and the drain pump, and then secure them in

place with CBANDs.

Wrap the pipe cover connection with vinyl tape to close

the gap. (Fig. 6)

3-3 Wiring connections

(1) Remove the CONTROL BOX COVER from the unit by

unscrewing the two screws on the cover. (Fig. 7)

(2) Unscrew the (c)CONTROL BOX fixing screw. (Fig. 7)

3DRAIN HOSE

6HOSE BAND

Fig. 5

4PIPE COVER 1

5PIPE COVER 2

Vinyl tape (locally procured)

To be gap-free

CBAND 2

Fig. 6

CONTROL BOX

COVER

(c)

Fig. 7

(3) Remove the short-circuit connector from CN4F

on the control board (white, 4P). (Fig. 8)

(4) Route the two drain pump wires behind the CON-

TROL BOX and into the CONTROL BOX.

Lift the CONTROL BOX in the direction of the

arrow (d) to allow the wires through. (Fig. 8)

✻ Do not pinch the wires.

(5) Wind the drain pump wire (connector: blue, 3P)

around 9FERRITE CLAMP once, and fix it in

place with 0BAND. (Fig. 9)

(6) Connect the drain pump wire (connector: blue,

3P) to CNP on the control board, and connect the

float switch wire (white: 4P) to CN4F on the con-

trol board respectively. (Fig. 8)

(7) Place the screw(c) that was removed in Step 3-

3.(2) above back on. (Fig. 7)

(8) Fix the two drain pump wires with 8CLAMPs to

the unit. (Fig. 10)

CN4F CNP

Short-circuit connector

Drain pump wires (2 wires)

(d)

Drain pump wire(2 wires)

8CLAMP

Fig. 8

Blue:3P

9FERRITE CLAMP @BAND

Fig. 9

Fig. 10

4-1. Insert the ADRAIN HOSE 2 into the drain port (insertion margin: 25mm).

(The drain hose must not be bent more than 45˚to prevent the hose from breaking or clogging.)

(Attach the hose with glue for the hard vinyl chloride pipe, and fix it with the CBAND 2.)

4-2. Attach the drain pipe (O.D. ø32 PVC TUBE, field supply).

(Attach the pipe with glue for the hard vinyl chloride pipe, and fix it with the CBAND 2.)

4-3. Perform insulation work on the drain pipe (O.D. ø32 PVC TUBE) and on the socket (including elbow).

4-4. Check the drainage.

4-5. Attach the BPIPE COVER 3 and, fix it with the CBAND 2 to insulate the drain port.

BPIPE COVER 3

CBAND 2

Visible part Insertion margin

Insertion margin Insulating material (field supply)

Drain pipe

(O.D. ø32 PVC TUBE, field supply)

Max.180 ±5 mm

ADRAIN HOSE 2

CBAND 2

DRAIN PUMP

2535 25

To be gap free. The joint section of the

insulation material meet must be at the top.

•Ensure that the drain piping is downward (pitch of more than 1/100) to the outdoor (discharge) side. Do not provide any trap

or irregularity on the way.

•Ensure that any cross-wise drain piping is less than 20 m (excluding the difference of elevation). If the drain piping is long,

provide metal braces to prevent it from waving. Never provide any air vent pipe. Otherwise drain may be ejected.

•Use a hard vinyl chloride pipe O.D. ø32 for drain piping.

•Ensure that collected pipes are 10 cm lower than the unit body's drain port.

•Do not provide any odor trap at the drain discharge port.

•Put the end of the drain piping in a position where no odor is generated.

•Do not put the end of the drain piping in any drain where ionic gases are generated.

4 Drain piping work

Correct piping

Wrong piping

AInsulation (9 mm or more)

BDownward slope (1/100 or more)

CSupport metal

KAir bleeder

LRaised

MOdor trap

DO. D. ø32 PVC TUBE

EMake it as large as possible.About 10 cm.

FIndoor unit (Drain pump)

GMake the piping size large for grouped piping.

HDownward slope (1/100 or more)

IO. D. ø38 PVC TUBE for grouped piping.

(9 mm or more insulation)

JUp to 580 mm

NDrain hose (accessory)

OHorizontal or slightly upgradient

Grouped piping

Max. 20m

1.5-2m

Max. 300mm

FFF

Insert pump's end 2 to 4 cm.

About 2000 cc

Water

Do not splash water on the drain pump coil or the

float switch wire through hole when pouring water.

SWE

Make sure that the drain-up mechanism operates normally

for discharge and that there is no water leakage from the

connections.

•Be sure to confirm the above in a period of heating operation.

•Be sure to confirm the above before ceiling work is done in the

case of a new construction.

•Make sure that water is not leaking from the connection (e) on

the drain pump shown in the right figure.

5 Confirming drain discharge

5-1. Fill water into the feed water pump using a feed water tank. In filling, be sure to put the end of the pump or

tank in a drain pan. (If the insertion is incomplete, water may flow over the machine.)

✻ Do not splash water on the drain pump coil or the float switch wire through hole when pouring water.

5-2. Perform the test run in cooling mode, or turn on the switch SWE on the controller circuit board. (The drain

pump and the fan are forced to operate without any remote controller operation.) Make sure using a transpar-

ent hose that drain is discharged.

5-3. After confirmation, cancel the test run mode, and turn off the main power. When the switch SWE has been

turned on, turn it off, and attach the CONTROL BOX COVER and the DRAIN PUMP COVER in the original

positions.

SWE SWE

ON OFF ON OFF

SEZ model

SWE SWE

OFF ON OFF ON

PEFY model

SWE SWE

ON OFF ON OFF

SEZ model

SWE SWE

OFF ON OFF ON

PEFY model

(e)

Inhaltsverzeichnis

Andere Mitsubishi Wasserpumpe Handbücher

Mitsubishi

Mitsubishi MBP15G Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung