ML Accessories BL01BK Bedienungsanleitung

INSTALLATION & MAINTENANCE MANUAL

BL01BK

These instructions should be read carefully and retained after installation by the

end user for future reference and maintenance.

These instructions should be used to aid installation of the following product:

BL01BK

GENERAL INSTRUCTIONS

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring

Regulations (BS7671) and current Building Regulations. If in any doubt, consult a

qualiﬁed electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this product is ﬁtted) does not exceed

the rating of the circuit cable, fuse or circuit breaker

• Please note the IP (Ingress Protection) rating of this product when deciding the location

for installation

• This product is Class I and must be earthed

• This product is IP44 rated

INSTALLATION & MAINTENANCE MANUAL

These instructions should be read carefully and retained after installation by the end user for future reference

and maintenance.

These instructions should be used to aid installation of the following product:

BL01BK

SAFETY

•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

•Please isolate mains prior to installation or maintenance

•Check the total load on the circuit (including when this product is fitted) does not exceed the rating of

the circuit cable, fuse or circuit breaker

•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

•This product is Class I and must be earthed

•This product is IP44 rated

INSTALLATION

•Provide power to the required point of installation (refer to BS7671 for correct cabling methods).

Suitable IP rated junction boxes should be used where required

•Round cable should be used for the mains supply. The use of flat cable will cause water ingress to the

fitting

•Carefully remove the fascia and glass from the luminaire housing by unfastening the two screws on the

front (see Fig. 1)

Fig .1

•Cut a suitable recess in the mounting surface, mark the location of the fixing holes, and drill the holes

ensuring not to infringe with any gas/water pipes or electrical cables

•Feed the mains cable through the rubber grommet to retain IP rating and secure the luminaire housing

into the hole using the plugs and screws provided. Rubber washers or sealant should be applied

around the screw heads to prevent water ingress. Mortar around the luminaire housing if necessary

and allow to set before continuing

•Connect the luminaire to the mains supply ensuring the correct polarity is observed: L –Live (brown),

E –Earth (green/yellow), N –Neutral (blue). Oversleeving is provided to help protect the incoming

mains cable. The cable and terminal block should be kept away from the lamp to prevent heat damage

•Insert a suitable E27 lamp (not included), max. 40W

•Refasten the glass (frosted side in) and chosen fascia ensuring the gasket is in place and a tight seal

is made

•Switch on and check for correct operation

•Should the protective glass be cracked or damaged it should be replaced immediately

•This fitting must not be used without the protective glass installed

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance

testing. Irreparable damage will occur if this instruction is not followed.

This product is not suitable for direct installation in the ground, nor in a retaining wall where the ground behind

may become saturated.

This product is not suitable for installation in or near a coastal or marine environment.

INSTALLATION

• Provide power to the required point of installation (refer to BS7671 for correct cabling

methods). Suitable IP rated junction boxes should be used where required

• Round cable should be used for the mains supply. The use of ﬂat cable will cause water

ingress to the ﬁtting

• Carefully remove the fascia and glass from the luminaire housing by unfastening the two

screws on the front (see Fig. 1)

• Cut a suitable recess in the mounting surface, mark the location of the ﬁxing holes, and

drill the holes ensuring not to infringe with any gas/water pipes or electrical cables

• Feed the mains cable through the rubber grommet to retain IP rating and secure the

luminaire housing into the hole using the plugs and screws provided. Rubber washers or

sealant should be applied around the screw heads to prevent water ingress. Mortar

around the luminaire housing if necessary and allow to set before continuing

Fig. 1

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or

insulation resistance testing. Irreparable damage will occur if this instruction is not followed.

This product is not suitable for direct installation in the ground, nor in a retaining wall where

the ground behind may become saturated.

This product is not suitable for installation in or near a coastal or marine environment.

• Connect the luminaire to the mains supply ensuring the correct polarity is observed:

L – Live (brown), E – Earth (green/yellow), N – Neutral (blue). Oversleeving is provided to

help protect the incoming mains cable. The cable and terminal block should be kept away

from the lamp to prevent heat damage

• Insert a suitable E27 lamp (not included), max. 40W

• Refasten the glass (frosted side in) and chosen fascia ensuring the gasket is in place and

a tight seal is made

• Switch on and check for correct operation

• Should the protective glass be cracked or damaged it should be replaced immediately

• This ﬁtting must not be used without the protective glass installed

GENERAL

Clean the external surfaces with a damp cloth using a mild solution of detergent and warm

water only, do not use aggressive cleaning products or solvents which may damage the

product.

Do not use any source of high-pressure washers to maintain or clean this luminaire.

This product is dimmable dependent on lamp type

This product should be recycled in the correct manner when it reaches the end of its life.

Check local authorities for where facilities exist.

WARRANTY

This product has a warranty of 1 year from date of purchase. Failure to install this product

in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper

use, or removal of the batch code will invalidate the warranty. If this product should fail

within its warranty period, it should be returned to the place of purchase for a free of

charge replacement. ML Accessories does not accept responsibility for any installation

costs associated with the replacement product. Your statutory rights are not affected. ML

Accessories reserve the right to alter product speciﬁcation without prior notice.

DCOCT21_V1

ML Accessories Limited LU5 4LT

www.mlaccessories.co.uk

INTERNATIONAL

CONTACT DETAILS

INTERNATIONAL

CONTACT DETAILS

INTERNATIONAL

CONTACT DETAILS

Inhaltsverzeichnis

Andere ML Accessories Beleuchtungsausrüstung Handbücher

ML Accessories

ML Accessories NH016W Bedienungsanleitung

ML Accessories

ML Accessories LSPIKEA Bedienungsanleitung

ML Accessories

ML Accessories Knightsbridge SPIKEW Handbuch

ML Accessories

ML Accessories SHE1BEMP Bedienungsanleitung

ML Accessories

ML Accessories MLBA6045 Series Bedienungsanleitung

ML Accessories

ML Accessories BATSCWMST4 Bedienungsanleitung

ML Accessories

ML Accessories SPIKEW Bedienungsanleitung

ML Accessories

ML Accessories 12DCIP40 Bedienungsanleitung

ML Accessories

ML Accessories T8LED Series Bedienungsanleitung

ML Accessories

ML Accessories BT ACTS Series Bedienungsanleitung

ML Accessories

ML Accessories CFR5CCT Bedienungsanleitung

ML Accessories

ML Accessories NH023AW Bedienungsanleitung

ML Accessories

ML Accessories EMPOWER2 Bedienungsanleitung

ML Accessories

ML Accessories 4IPB Bedienungsanleitung

ML Accessories

ML Accessories BL5BK Bedienungsanleitung

ML Accessories

ML Accessories RWL2A Bedienungsanleitung

ML Accessories

ML Accessories WALL1 Bedienungsanleitung

ML Accessories

ML Accessories SUR5LED Bedienungsanleitung

ML Accessories

ML Accessories Knightsbridge EMTWINPC Bedienungsanleitung

ML Accessories

ML Accessories OSPCKIT Bedienungsanleitung

ML Accessories

ML Accessories OPRCDKIT Bedienungsanleitung

ML Accessories

ML Accessories EMPDL Bedienungsanleitung

ML Accessories

ML Accessories TPOV60B Bedienungsanleitung

ML Accessories

ML Accessories OWALL1 P Series Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung